• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.04a
• /
• pp.682-688
• /
• 2008

Transverse flux machine (TFM) has been considered as a promising driving machine especially at the low-speed applications because it has higher power density, torque and efficiency than the conventional electrical motors. However, it has complicated structure, large torque ripple and sometimes unbalanced magnetic force due to its inherent structure. This paper investigates the characteristics of torque ripple and unbalanced magnetic force of a rotatory two-phase TFM due to the teeth geometry by using the 3-dimensional finite element method, and it develops a rotatory two-phase TFM with herringbone teeth to reduce the torque ripple as well as to eliminate the unbalanced magnetic force.

• Transactions of The Korea Fluid Power Systems Society
• /
• v.7 no.4
• /
• pp.44-49
• /
• 2010

This paper represents solenoid design of control valve for incline angle control in variable compressor. Some theoretical and numerical analysis were performed to analyse solenoid and compared with experimental results. Maxwell program was used for numerical analysis. Through redesigns of housing body, plunger, core, and disk in control valve, the needed force was gotten. Reduction of core groove and housing body air-gap had a large influence on magnetic force. But increasing of disk thickness had little effect on magnetic force. Control valve efficiency could be improved through solenoid redesign.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.05a
• /
• pp.297-300
• /
• 2002

In this study, the deformation of the free surface motion of a magnetic fluid for the change in electromagnetic force is discussed and carried out theoretically and experimentally on the basis of Rosensweig Ferrohydrodynamic Bernoulli Equation. While applied magnetic fields are induced by 4$\times$4 electromagnet located under the magnetic fluid, the surface of the magnetic fluid is formed the balance of surface force, gravity, pressure difference, magnetic normal pressure and magnetic body farce. In case, magnetic fluid in characteristics of fluid adjusted to the opposite direction of the gravity direction. thus, the device of a magnetic fluid proposed the surface actuator. The device of surface deformation as well comparison between numerical simulation and experiments as will be presented.

• 한국전산유체공학회:학술대회논문집
• /
• 1995.10a
• /
• pp.132-137
• /
• 1995

Numerical analysis is conducted on the deformation of free surface of magnetic fluid. Steady magnetic fields are induced by a circular current loop. Governing equations of magnetic fields are solved by using the concept of vector potential. The free surface of magnetic fluid is formed by the balance of surface force, gravity, pressure difference, magnetic normal pressure and magnetic body force. The deformations of free surface of magnetic fluid are qualitatively clarified. And, the patterns of steady non-uniform magnetic fields induced by a circular current loop are quantitatively presented.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.17 no.1 s.118
• /
• pp.33-40
• /
• 2007

Rotatory two-phase transverse flux machine(TFM) is a relatively new type of motor with high power density, high torque, and low speed in comparison to conventional electrical motors. However, it has some shortcomings,.i.e. complex construction and high possibility of the magnetically induced nitration due to its inherent structure. This Paper investigates the characteristics of the magnetic force and the torque in the rotatory two-phase TFM by using the 3-D finite element method and the spectral analysis. This research shows that the average torque decreases and that the torque ripple increases as the phase delay increases. It also shows that the unbalanced magnetic force is one of the dominant excitation forces in this machine. And it proposes a new topology of rotatory two-phase TFM to eliminate the unbalanced magnetic force.

• Proceedings of the KIPE Conference
• /
• 2000.07a
• /
• pp.729-734
• /
• 2000

This paper proposes virtual-magnetic system by a force-reflecting interface to drive a ultrasonic motors(USMs) To approach virtual magnet in graphic the 6 dDOF force-reflecting interfaces provides force feedback to users as if I is magnetic-force, So users can feel real magnet Effectively to display the magnetic-force we need the interface with specific characteristics such as low inertia almost zero friction and very high stiffness As an actuator for the interface the USMs have many good advantage satisfied these conditions over conventional servo motors. To estimate capability of this virtual-magnetic system we did an experiment of magnetism based on coulomb's law when Coulmb's low apply this experiment it is vey conformable to real magnet

• Tribology and Lubricants
• /
• v.11 no.1
• /
• pp.20-26
• /
• 1995

Most magnetic bearings are based on the attractive force between the magnets and ferrous materials. One of the disadvantages of such attractive type magnetic bearings is the instability so that an active control device is necessary to operate bearing successfully. In this study a repulsive type magnetic bearing is analyzed which uses eddy current as a force source. The load capacities are analyzed for the various gap sizes, the rotor velocities and the frequencies of current supplied to electromagnet. Analytic Results show that as the gap size decreases, the levitation and drag forces increase, while the number of poles increasqs, the drag force decreases in the higher linear velocity region. Experimental results show that as the gap size decreases the levitation and the drag force increase, and as the velocity of rotor increases, the drag is larger than the levitation force up to certain velocity. But after that, the levitation is larger than the drag force. As the frequency of the current increases the levitation and drag decreases while the thickness of rotor gets thicker the forces decrease because of increase in eddy current loss.

• Journal of international Conference on Electrical Machines and Systems
• /
• v.2 no.1
• /
• pp.9-15
• /
• 2013

This paper presents a uniform analytical model by energy method and Fourier series expansion to analyze detent force in uneven magnetic field for permanent magnet linear synchronous motor (PMLSM). The model reveals that detent force in long-primary type is mainly influenced by non-ideal distribution of permanent magnet magnetic motive force, while nounified air-gap permeance makes a great impact on detent force of short-primary type. Hence, magnetic field similarity of motor design techniques referring rotary counterpart are adopted. For long-primary type novel method of splitting edge magnets is proposed to reduce end effects force, and optimal widths of edge tooth in short-primary type also verify the effectiveness of magnetic field similarity. The experimental results validate finite element analysis results.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.3
• /
• pp.1349-1355
• /
• 2015

It is difficult to calculate the magnetic force of an object of magnetic material in contact with other objects using the existing methods, such as Maxwell stress tensor method, magnetic charge method, or magnetizing current method. These methods are applicable for force computation only when the object is surrounded by air. The virtual air-gap concept has been proposed for calculating the contact force. However, its application is limited to magneto-static system. In this paper, we present the virtual air-gap concept for contact surface force in the eddy-current system. Its validity and usefulness are shown by comparison between numerical and experimental examples.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2012.06a
• /
• pp.121-122
• /
• 2012

In this research, we studied on improvement of the attraction force of solenoid operated valve for normal operation in harsh environment like vessel. Attraction force of the solenoid valves is effected by the B-H characteristics of magnetic material and the size of coil. In order to specify impact of the affection, we performed the B-H characteristics test and attraction force. Test results show that magnetic flux densities of the materials are difference each other more than 2 times in same magnetic intensity, and attraction force of the solenoid valve is 1.7 times difference as changes of resistance and the number of coil winding of solenoid.