• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2001년도 Proceedings ICPE 01 2001 International Conference on Power Electronics
• /
• pp.1-6
• /
• 2001

In this article, the fundamental concept, characteristics and application potentials of coreless printed-circuit-board (PCB) transformers are described. Coreless PCB transformers do not have the limitations associated with magnetic cores, such as the frequency limitation, magnetic saturation and core losses. In addition, they eliminate the manual winding process and its associated problems, including labor cost, reliability problems and difficulties in ensuring transformer quality in the manufacturing process. The parameters of the printed windings can be precisely controlled in modern PCB technology. Because of the drastic reduction in the vertical dimension, coreless PCB transformers can achieve high power density and are suitable for applications in which stringent height requirements for the circuits have to be met. A transformer's power density of $24W/cm^2$ has been reported in a power conversion application. When used in an isolation amplifier application, coreless PCB transformers tested so far enable the amplifier to achieve a remarkable linear frequency range of 1MHz, which is almost eight times higher than the frequency range of 120kHz in existing Integrated-Circuit products. PCB materials offer extremely high isolation voltage, typically from 15kV to 40kV, which is higher than many other isolation means such as optocouplers. It is envisaged that coreless PCB transformers can replace traditional core-based transformers in some industrial applications. Their application potentials deserve more attention and exploration.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 영호남학술대회 논문집
• /
• pp.13-16
• /
• 2000

In this study, we have fabricated nonequilibrium $Fe_{85.6}Zr_{3.3}B_{5.7}Ag_{5.4}$ thin film, which contains an additional insoluble element Ag, by using DC magnetron sputtering method. We have investigated the magnetic properties of amorphous $Fe_{85.6}Zr_{3.3}B_{5.7}Ag_{5.4}$ thin film as a function of rotational field annealing(RFA). After deposition, the amorphous $Fe_{85.6}Zr_{3.3}B_{5.7}Ag_{5.4}$ thin film annealed by rotational field annealing method at $350^{\circ}C$ for an hour was founded to have high permeability of 8680 of 100 MHz, 0.2 mOe, low coercivity of 0.86 De and very low core loss of 1.3 W/cc at 1 MHz, 0.1T.

• 한국해양학회지:바다
• /
• 제1권1호
• /
• pp.1-12
• /
• 1996

북태평양의 KODOS-90 지역에서 채취한 4-6 m 길이의 중력 코아 3개를 대상으로 자기층서 확립 및 코아들 간의 상호대비를 위하여 고지자기 연구를 수행하였다. 연구된 퇴적물은 자기적으로 안정된 잔류자화를 보유하고 있으며, 이 들의 자기극성(Polarity)변화는 지자기층서표(Geomagnetic Polarity Time Scale) 의 플라이오-플라이스 토세(Plio-Pleistocene) 기간과 대비된다. 중력 코아 26의 대자율은 285 cm 지점에서 급격한 변화를 보여 주어, 이 지점에 비교적 오랜기간 의 결층(Hiatus)이 존재함을 지시한다. 각 코아의 자극변화에 의한 평균 퇴적속도 는 중력 코아 20에서 0.09 cm/1000yr 이며, 중력 코아 08과 중력 코아 26은 중력 코아 20에 비하여 각각 약 2.7배와 1.4배의 상대적으로 높은 퇴적율을 보여준다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 춘계학술대회논문집
• /
• pp.672-675
• /
• 2006

It is becoming more significant to develop a rotary VCM type actuator for small form factor ODD, as portables are getting more and more popularized nowadays. In this paper, the procedure of development of the actuator which is applicable to compact flash II card and is fit in the specification of BD 1X is explained. This is based on the rotary VCM type actuator, which is good for reducing thickness. Air core solenoid coil is used in order to do focusing mechanism. And the total weight is reduced by using the structure of steel-aluminium-steel triple layer, so, the stiffness is still adequate. Additionally, the tracking coil is moved next to the actuator, so the total length was reduced, then the actuator become applicable to compact flash II card. The force of Magnetic Circuit is improved by using Magnetic Circuit DOE. And flexible mode frequency improved through the DOE of structure part. Modeling was exactly done in consideration of air core solenoid coil and pivot bearing. It is confirmed that the designed model is satisfied with the specification of BD 1X and is applicable to Compact Flash II card.

• 전자공학회논문지A
• /
• 제28A권9호
• /
• pp.721-728
• /
• 1991

In this paper, a magneto-optic modulator has been designed by using single crystal BSO and polycrystal ZnSe as Faraday cells. And practical core-type optical current sensors using pure iron and permalloy have been prepared and experimented. In order to obtain efficient magnetic field detection, LED(NEC OD08358, 0.87 $\mu$m) was used as optical source, PIN-PD(OD-8454)as optical receiver and multi-mode optical fiber (100/140$\mu$m) as transmission line. The characteristics matrix of the optical element was calculated by Stokes parameter, and optic modulation characteristics equations were derived by Muller matrix. Electromagnetic analysis program (FLUX 2D, micro VAX 3600) by finite element method was used to find the magnetic flux density around the core. The measuring error of the output voltage to input current has been masured below 5% in the range of 50A to 1000A. As the temperature was changed from -20$^{\circ}C$ to 60$^{\circ}C$, the maximum measurement error of the optical output has been found to be 0.5% at 60$^{\circ}C$. These experimental results show good temperature and linearity characteristics. The SNR of the overall system was 47dB in case of 600A (250.2 Oe) conductor current and the system has good noise immunity.

• Journal of Magnetics
• /
• 제21권2호
• /
• pp.192-196
• /
• 2016

The Fe-Si-B-Nb-Cu alloys containing Ca and Al were rapidly solidified to thin ribbons by melt-spinning. The ribbons were ball-milled to make powders, and then mixed with 1 wt.% water glass and 1.5 wt.% lubricant. The mixed powders were burn-off, and then compacted to form toroidal-shaped cores, which were heat treated to crystallize the nano-grain structure and to remove residual stress of material. The characteristics of the powder cores were analyzed using a differential scanning calorimetry (DSC) and a B-H meter. The microstructures were observed using transmission electron microscope (TEM). The optimized soft magnetic properties (${\mu}_i$ and $P_{cv}$) of the powder cores were obtained from the Ca and Al containing alloys after annealing at $530^{\circ}C$ for 1 h. The core loss of Fe-Si-B-Nb-Cu-based powder cores was reduced by the addition of Ca element, and the initial permeability increased due to the addition of Al element.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 제38회 하계학술대회
• /
• pp.240-241
• /
• 2007

연자성 분말의 독특한 특성은 3D 등방성 강자성체 이며, 이 때문에 3차원적 자속(flux)를 활용할 수 있어 전기 강판(sillicon steel)에 비해 3차원 성형시 유리한 장점을 가지고 있다는 점이다.[1] 따라서 본 논문에서는 연자성 분말 (Soft Magnetic Composites)의 3차원 성형시 각 성형 형태에 따른 압분 시료의 전기적, 기계적 특성에 대한 연구를 하였다. 연자성 분말의 코어 형상을 크게 ' '형으로 구분하여 압분 코어를 만든 후 압분 코어의 Overhang 각도 및 코어 Teeth의 길이에 따른 파라미터에 변화를 주어 철손 및 경도, 밀도를 측정 하였다. 이 논문에서 우리는 3차원 코어 성형시 전기적, 기계적 특성이 가장 우수한 코어 성형 조건을 연구해 낼 수 있었다.

• 조명전기설비학회논문지
• /
• 제28권5호
• /
• pp.92-97
• /
• 2014

The SRM is a doubly salient, singly excited machine. The torque is developed by the tendency for the magnetic circuit to adopt a configuration of minimum reluctance, i.e. for the rotor to move into in line with the stator poles and to maximize the inductance of the coils excited. It is common practice to combine them into groups of poles which are excited simultaneously; for example, 8/6 SRM (8 stator poles and 6 rotor poles) for 4 phases, 6/4, 12/8 SRM for 3 phases, 4/2, 6/3 SRM for 2 phases. Small number of phases in two-phase SRMs allows more cost savings with regards to the switching devices in the converter. The stator back irons of two phase 6/3 SRM and C-core 4/3 SRM does not experience any flux reversal as the flux is in the same direction whether phase A or B is excited. In this study, the similarities, the differences, and structural characteristics between the two SRMs was studied, The magnetic analysis also has been carried out by the finite element method analysis (FEM).

• 한국자기학회지
• /
• 제5권5호
• /
• pp.478-482
• /
• 1995

The iron-based Metglas 2605S3A amorphous alloy ribbons are annealed at $435^{\circ}C$ for various periods from 5 to 210 min, and the effect of annealing is investigated on the dc magnetic properties of the ribbon. Typical square-type hysteresis loops are observed for the ribbons annealed fo 5 min, indicative of the nearly complete removal of residual stresses which are produced during melt-quenching. As the annealing time increases, the coercivity increases and the shape of hysteresis loops transforms to round type and finally to sheared one at the longest annealing time of 210 min. These results may be explained by the formation of clusters with chemical shortorder and very fine crystallites (at the annealing time of 210 min), and the diffusion-induced stresses during the formation of the clusters. For the samples annealed for 5 min, very good dc properties of the squareness ratio, coercivity and maximum permeability are observed, but, rather unexpectedly, the initial permeability is found to be very low. These results are considered to be due to a simple domain structure consisting of very small number of $^{\circ}$ domains.

• Structural Engineering and Mechanics
• /
• 제78권5호
• /
• pp.557-572
• /
• 2021

The current study considers free vibration of the spherical panel with magnetorheological (MR) fluids core and magneto-electro-elastic face sheets. The panel is subjected to electro-magnetic loads and also is located on an orthotropic visco-Pasternak elastic foundation. To describe the displacement components of the structure, the first-order shear deformation theory (FSDT) is used and the motion equations are extracted by employing Hamilton's principle. To solve the motion differential equations, Navier's method is selected as an exact analytical solution for simply supported boundary conditions. Effect of the most important parameters such as magnetic field intensity, loss factor, multi-physical loads, types of an elastic medium, geometrical properties of the panel, and also different material types for the face sheets on the results is considered and discussed in details. The outcomes of the present work may be used to design more efficient smart structures such as sensors and actuators.