• 한국표면공학회지
• /
• 제31권1호
• /
• pp.34-44
• /
• 1998

Stainless steel is being used widely lor various purposes due to its good corrosion resistance. There has becn much research to produce colored stainless sterl by several methods. In this experiment, we coated TixN film on the SUS304 substrate with thc DC magnetron sputtering system and studied the internal structurc and adhesive strength of the films as a function of the coating conditions. Before lhe specimen was coated, a sputter etching was very effective in removing the$\delta$ Fe(BCC) phase as well as the contaminant and oxide layer as well as increasing rotghness. Five-stage failure mode appeared with increased scratch load with the TIN films coated on the SUS304 in this manner ; tensile failure-,conformal failure-,buckling failure->chipping failurc and spalling Failure. When the failure was terminated at the initial stage, the film will have good adhesion. But, if syalling failure has occurred at the initial scratch, then the adhesion will be poor. The interlayer between thc coated film and thc substratc was homogeneously adhcsive when the $\gamma'-Fe_4N$ phase wasn't detected in the XRD analysis and the adhesive strength only was reduced by surPace defects. But, when the ,$\gamma'-Fe_4N$N phasc was detected in the XRD analysis, the adhesive strength was very poor.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제41회 하계 정기 학술대회 초록집
• /
• pp.132-132
• /
• 2011

The sheet resistance (Rs) of undoped GaN films on AlN/c-plane sapphire substrate was investigated in which the AlN films were grown by R. F. magetron sputtering method. The Rs was strongly dependent on the AlN layer thickness and semi-insulating behavior was observed. To clarify the effect of crystalline property on Rs, the crystal structure of the GaN films has been studied using x-ray scattering and transmission electron microscopy. A compressive strain was introduced by the presence of AlN nucleation layer (NL) and was gradually relaxed as increasing AlN NL thickness. This relaxation produced more threading dislocations (TD) of edge-type. Moreover, the surface morphology of the GaN film was changed at thicker AlN layer condition, which was originated by the crossover from planar to island grains of AlN. Thus, rough surface might produce more dislocations. The edge and mixed dislocations propagating from the interface between the GaN film and the AlN buffer layer affected the electric resistance of GaN film.

• 한국세라믹학회지
• /
• 제35권10호
• /
• pp.1040-1048
• /
• 1998

Ferroelectric properties of{{{{ { { { {SrBi }_{2 }Ta }_{2-x }Nb }_{x }O }_{9 } }} (SBIN) thin films were affected by the amount of Bi content in SBTN. The addition of Bi into the SBTN films could be accomplished by heat treating SBTN/Bi2O3/SBTN het-erostructures fabricated by r.f. magnetron sputtering method. The variation of Bi content was controlled by changing the thickness of the sandwiched Bi2O3 in SBTN/Bi2O3/SBTN heterostructure from 50 to 400$\AA$. As changing the thickness of the sandwiched Bi2O3 in Bi2O3 films was increased from 0 to 100$\AA$ the grain grew faster and the ferroelectric pro-perties were improved. On the other hand when the thickness of Bi2O3 films was thicker than 150$\AA$ the fer-roelectric properties were deteriorated Especially for SBTN thin films inserted by 400$\AA$ Bi2O3 layer a Bi2Phase appeared as a second phase resulting in poor ferroelectric properties. The maximum remanent po-larization (2Pr) and coercive field(Ec) were obtained for the SBTN/Bi2O3/(100$\AA$)/SBTN thin films. In this case 2Pr and Ec were 14.75 $\mu$C/cm2 and 53.4kV/cm at an applied voltage of 3V respectively.