• Elastomers and Composites
• /
• 제54권2호
• /
• pp.135-141
• /
• 2019

Polyphenylene sulfide (PPS) was filled with glass fiber (GF), aramid fiber (AF), and solid lubricants to improve the mechanical properties and wear resistance. The addition of GF effectively enhanced the tensile strength, flexural modulus, and impact strength of PPS, while solid lubricants such as polytetrafluoroethylene (PTFE), molybdenum disulfide ($MoS_2$), and tungsten disulfide ($WS_2$) lowered the friction coefficients of the composites to below 0.3. The ball nut and motor pulley of the electric power steering (EPS) were manufactured using the PPS composites, and feasibility was ascertained thereafter by conducting the durability test. The composites filled with GF and AF showed high mechanical strength, but slip occurred at the interface between the pulley and belt while testing above $50^{\circ}C$. When small amounts of lubricants were added, the slip was no longer detected because of the suppression of friction heat. It is realized that the low friction as well as high mechanical properties is important to ensure the reliability of plastic pulleys.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.351-352
• /
• 2002

In this paper, studies were made on the palm oil methyl ester (POME) added lubricants using FT-IR for monitoring oil degradation. In order to assess the degradation characteristics of POME added lubricant by FT-IR, static oxidation test was conducted using three different blended lubricants (viz, zero percent POME, five percent POME and ten percent POME with mineral-based oil) for 280 hrs. The oxidation temperature was set at $140^{\circ}C$. FT-IR quantitative data indicate an increased in oxidation products which was formed from 10% POME added lubricants after 280 hrs of oxidation test. The 5% POME added lubricant and mineral-based lubricant (without POME) showed less oxidation product after the test. From the FT-IR spectrum analysis of the oxidized oils it could be concluded that 5% POME can improve the performance of mineral-based oil by forming protective films.

• 소성∙가공
• /
• 제10권4호
• /
• pp.319-328
• /
• 2001

Quantitative evaluation of the tribological conditions at the tool-workpiece interface in metal forming is usually accomplished by the ring compression test. This paper describes an experimental investigation into friction factor under warm forming conditions according to the lubricants and the lubricating methods using the ring compression test. Four different lubricants, two water based graphite and two oil based graphite lubricants, and three different lubricating methods were applied in the experiments. Calibration curves with the friction shear factor were obtained using FEM analysis and verified by the experimental results. The influence of lubricant and lubricating methods on friction are discussed. In the ring compression test, the lower friction factor got to spray the oil based lubricant on die and billet in warm forging temperature.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 추계학술대회논문집
• /
• pp.140-143
• /
• 2003

The drawbead is an important part in sheet metal forming for automotive part and its effect is affected by various process parameters. Therefore in this study, drawbead friction test was performed at various process parameters - panels (cold rolled and galvanized sheet steel), lubricants (having three different viscosities), bead materials(steel, iron) and surface treatment of bead (Cr plating). Circular shape bead has been used for the test. The results show that friction and drawing characteristics were mainly influenced by the nature of zinc coating, viscosity of lubricants, surface treatment of a bead and hardness of coated layer.

• Tribology and Lubricants
• /
• 제11권2호
• /
• pp.34-43
• /
• 1995

The boundary films formed in sliding on steel surfaces were characterized using various lubricants. The mechanism of boundary film formation and loss was investigated over a range of temperature. The thickness of the boundary films was monitored in-situ by an ellipsometer, and the composition of the films was analyzed by XPS. The performance of the lubricants is closely associated with boundary film forming ability. In order to achieve high load carrying capacity, a boundary film must be formed on the surface. Sliding is necessary to form the films and some time is also required. As temperature increases, chemical reactivity increases the film formation rate, while the film removal rate increases due to thg decrease of durability of the boundary film material. There is a balance between these two competing mechanisms and this balance is reflected in the boundary film thickness.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1990년도 제12회 학술강연회초록집
• /
• pp.16-35
• /
• 1990

The mechanism of failure of lubricated surfaces at high sliding speeds was Investigated. Experiments were performed with the ball-on-flat and cylinder-on-flat geometries, using lubricants of four different chemical reactivities. Surface failure was found to not be predictable using the ratlo, $\lambda$, of fluid film thickness to composite surface roughness except when chemically inert lubricants are used. Even then the influence of temperature rise on fluid film thickness does not adequately explain the low load carrying capacity of lubricants at high sliding speeds. which causes surface failure. The protective layers on sliding surfaces that form by chemical reaction with the lubricant were found to reduce the surface roughentrig and Increase the load carrying capacity of surfaces to values of $\lambda$ as low as 0.03. Neither the surface toughening nor the formation of the protective layers have been incorporated Into failure models for lubricated systems.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 제35회 춘계학술대회
• /
• pp.105-110
• /
• 2002

The use of microporous polymer lubricants (MPLs) can eliminate the storage, sealing, and pumping problems associated with liquid lubricants, This paper discusses the use of MPLs for a component as rolling-element bearings. An MPL composed of 40% HDPE and 60% ester oil was synthesized and the MPL was applied to a ball bearing. The MPL ball bearing, filled with the MPL instead of the usual grease pack, tested and compared with the usual grease sealed ball bearing. The MPL applied to a ball bearing showed lubricant properties as good as usual grease, and showed higher performance in bearing oil leakage test, rotating torque test and thermal test at high speed running than usual grease.

• Journal of Pharmaceutical Investigation
• /
• 제38권5호
• /
• pp.303-311
• /
• 2008

Highly hydrophobic lubricants including magnesium stearate may hinder water penetration into the tablet core resulting in delayed disintegration of fast disintegrating tablets. Alternative lubricants with equivalent lubricating properties may need to be incorporated into the tablet formulations. Sodium stearyl fumarate, glyceryl behenate and polyethylene glycol were evaluated regarding the tablet ejection energy, mechanical strength and disintegration time using Texture analyzer (TA). Resulting tablets were also compared with different particle sizes of granules and various compression forces. Among the tested lubricants, sodium stearyl fumarate was less sensitive to mixing time and also showed better or competitive tablet properties. During the experiments, TA was found to be very useful tool to investigate the tablet properties.

• 대한기계학회논문집
• /
• 제8권2호
• /
• pp.178-183
• /
• 1984

본 연구에서는 108개의 아르곤 입자가 Lennard-Jones의 포텐셜함수로 상호작 용하고 있는 고밀도 액체계에 높은 전단율울 작요시켜 외력에 의하여 물성의 변화가 일어나고 있는 비평형상태의 액체가 나타내는 현상을 분자동력학을 이용하여 미시적 인 관점에서 고찰하므로써, 높은 전단하중으로 인하여 윤활유 내부에서 전단응력이 발생하고, 이완되는 과정과 이로 인하여 점성이 저하하는등 비평형상태하의 물성변화 를 예측하는데 도움이 되고자 한다.

• Tribology and Lubricants
• /
• 제26권3호
• /
• pp.190-198
• /
• 2010

GTL(gas-to-liquid) fuel produced by the Fischer-Tropsch process using carbon monoxide(CO) and hydrogen(H2) is expected to be one of the environmental friendly fuel for alternative and blended to petrodiesel. But GTL have poor lubricity due to paraffin as main component of GTL which is not involve polar materials. In this paper, we had investigated the lubricity improvement of GTL fuels with various lubricants using HFRR(high frequency reciprocating rig).