• Proceedings of the Korea Concrete Institute Conference
• /
• 2000.04a
• /
• pp.247-250
• /
• 2000

As construction technology advances, most of concrete structures are becoming larger and taller. Therefore, high strength and high quality concrete is necessary for them. Nowadays, the proposal of using type IV(belite cement) is investigated to satisfy high flowing, low heat, and ho호 strength. In this study, the flow value and compressive strength of mortar were investigated according to usage of AE high range water reducer. And the slump flow value, falling time and heigth difference of concrete with beilte cement and ordinary cement were examined depending on water cement ratio, sand ratio and unit water weigth, and compressive strength to checked depending on age.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2017.05a
• /
• pp.204-205
• /
• 2017

In this study, flowability and strength on ultra high performance concrete(UHPC) pre-mixed binders with fiber was investigated. The flow of UHPC with pre-mixed binders was higher than that of seperate mixing conditions. The UHPC using PVA fiber with high specific surface area showed a low flow compared to steel fiber. An pre-mixing method led to improved strength of UHPC and low deviation of specimens due to dispersion effect of each materials.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.11a
• /
• pp.749-752
• /
• 2006

Autoclaved lightweight concrete (ALC) have high water absorption, low compressive strength and popout the origin of the low surface strength in its properties. These properties make troubles under construction such as cracking and popout. Thus, this study is to improve the fundamental strength by control of $SO_3$ ratio's and Sand Sulrry grain size. From the test result, Improved ALC have a good fundamental properties. Compressive strength, and abrasion's ratio were improved depending on increasing $SO_3$ ratio's and Sand Sulrry grain size control.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2004.11a
• /
• pp.809-812
• /
• 2004

The evaluation of characteristics of concrete coated by high performance surface penetration agency was examined through various tests, i.e., compressive strength, penetration depth, water and air permeability, absorption according to various high performance surface penetration agencies and various compressive strengths of base concrete. The 4 types of high performance surface penetration agencies were used i.e., organic, inorganic, water soluble, and alcohol soluble. And 3 types of compressive strength of base concrete were used such as 21, 24 and 30 MPa. The characteristics of concrete coated high performance surface penetration agency was more improved than that of non-coated concrete, and especially, water soluble inorganic agency was most effective. And if compressive strength of base concrete was low, the improved effects would be larger.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.997-1000
• /
• 2008

Strength development of concrete subjected to cold weather is generally delayed due to its low temperature. In case of soil nailing method, it is necessary to apply the shotcrete. However, the shotcrete placement under low temperature experiences retardation of strength development due to delayed hydration reaction. Therefore, in this paper, the use of fine particle cement which is produced through particle classification in cement manufacturing process, is discussed to enhance the strength development of the shotcrete under low temperature. According to the results, the concrete containing 100% of fine particle cement had excellent strength development even at $-9^{\circ}C$ of temperature and at 5days, it reached design strength with PE film curing. It is thought that more than 70% of fine particle cement can secure required strength of the shotcrete even at low temperature condition.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.181-184
• /
• 2008

The concrete is relatively fireproof materials. However, long-term exposure to high temperatures in the concrete strength is a phenomenon that occurs in the rapid degradation. In such a case, even low-strength estimates concrete expression to the General Non-destructive inspection is not appropriate to use the estimate. To overcome this problem, various mix conditions of the concrete specimen under 23, 200, 400, 600, $800^{\circ}C$ to a temperature, the correlation relationship between the ultrasonic velocity and the strength of concrete specimen is investigated and analyzed. This analysis estimates the high-temperature strength of the damaged concrete expression Non-destructive inspection of the proposal.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.05b
• /
• pp.433-436
• /
• 2006

This study is basic experiment for estimating influence of strength by curing temperature of concrete's heat of hydration and estimate relationship of compressive strength development by initial curing temperature factor, and then asume temperature factor which influence compressive strength development and for showing basic document of quality control. According to the result of managerial test pieces by the curing temperature factor high-curing temperature shows high strength on 3 day compare with low curing-temperature, shows higher strength than the piece of high curing temperature.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.04a
• /
• pp.271-275
• /
• 1998

Recently, in the trend of using aggregate, it is common that coarse aggregate is replaced with crushed stone and fine aggregate is replaced with sea sand as a replacing aggregate. In this study, to judge the adaptability of using antiwashout underwater concrete, we used mixed sand (river sand : sea sand= 5 : 5) and changed W/C. After carrying out the research on the strength development of the compressive strength of specimen, tensile strength, fluxural strength which is produced and cured in the air and salt water, we founded that when W/C was low and the amount of AWA and SP were increased, the state of strength development was excellent.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2021.11a
• /
• pp.131-132
• /
• 2021

According to the domestic specification, the curing of the specimen for strength management used to determine the time of the mold deformity of the structure concrete in early spring and early autumn is cured in the field structure condition. However, when the seal curing is performed in the field, the temperature of the specimen is very low compared to the temperature of the actual structure, so the strength of the structure concrete predicted based on the strength of the specimen is much undervalued than the actual one, which causes the mold to be deformed. Therefore, this study analyzed the temperature history and compressive strength characteristics of the specimen for strength management through other sealing curing at 5℃ and concrete of the actual structure, and presented the most suitable curing method.

• International Journal of Highway Engineering
• /
• v.11 no.1
• /
• pp.13-24
• /
• 2009

This study developed a high strength and performance concrete pavement material with low shrinkage and reflection of sunlight. Based on the literature review, a new mix-design of applying flash ash to improve the strength and performance of the concrete as well as to reduce the dry shrinkage is suggested. In addition, adding black pigment to reduce the reflection and technique of applying OAG (Optimized Aggregate Gradation) is also included. The result of the laboratory experiment indicates that the brightness and the reflection, which depends on the ratio of black pigment addition, did not deviate from the normal range. When OAG is considered for the mix-design, the strength and performance of the concrete improved greatly. In addition, the mix-design using fly ash reduced the dry shrinkage of concrete and improved the resistance to the permeation of chloride ion. Furthermore, the mix-design, which uses fly ash (25% replacement) and black pigment (3% addition) with the application of OAG, is found to be the most effective mix to reduce the shrinkage and reflection as well as improving the strength and performance of the concrete. The result of an economic analysis indicates that the initial construction cost of this proposed mix is more expensive than that of normal concrete pavement material. However, it can be more economic in the long run because the normal concrete pavement material is likely to cost more due to higher probability of maintenance and repair and higher social cost due to traffic accident, etc.