• 한국인쇄학회지
• /
• 제22권2호
• /
• pp.199-211
• /
• 2004

The drying speed of gravure ink are very fast because of evaporation drying type. The gravure ink are fitly selected variety resin and solvent for a wide range printing are adopted. Moreover, after-manufacture handling is necessary to various purposes. Though composition of gravure ink are same those of another printing ink, the viscosity of it are vary low compare with another printing inks. As property of variety printed matters, improvement of performance of printing layer and suitable after-manufacture handling, the more research of gravure ink are to be continue for development of printing technology. Generally, the gravure ink are made up resin, pigment, solvent and additive. Especially solvent are fitly selected for solution of resin, viscosity, and drying speed. Furthermore, it tis care of bad smell of remaining resin, poison and danger of fire of it. Because of the prevention of air pollution as restriction deflation of solvent, custody of dangerous object and improvement of work environment as labor safety hygiene and fire-low, the environment restriction of printing business become strict. This study has purpose of development of gravure ink of involved 30% below of alcohol is used for PVC film printing.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2007년도 춘계학술대회 논문집
• /
• pp.635-636
• /
• 2007

• 펄프종이기술
• /
• 제46권5호
• /
• pp.1-8
• /
• 2014

In this study, the influence of the physical properties of ink such as ink dispersity and emulsified amount on the printability of a coated paper was investigated with seven kinds of cyan inks. In addition, two kinds of coating formulations were tested to evaluate the effect of coating structure on the coated paper printability. It was found that the cyan ink with $2{\mu}m$ pigment size had the best dispersibility and hence the ink showed a best ink density on the two kinds of coated papers. When the emulsified ink A with IPA 20 wt% had a lower viscosity than emulsified ink B with IPA 10 wt%, the emulsified ink A showed relatively high value of the ink transfer rate in comparison with emulsified ink B. Despite the high value of ink transfer rate, the coated paper did not show a good printability because those inks with low viscosity due to a strong emulsification were easy to make print mottle on the coated paper.

• 한국인쇄학회지
• /
• 제21권2호
• /
• pp.89-100
• /
• 2003

We have reviewed the method for surface tension of printing inks. Most of the methods fir for the low viscosity inks and solvents for inks. However, the inks for the offset lithography and intaglio should have high viscosity and high tack. The elongation of the ink filaments has more effect on the measuring surface tension than the energy of the surface molecules. In this paper, we propose the elongation method to estimate the surface tension of high viscosity printing inks. Even though we could measure the surface tension for low viscosity inks such as gravure and screen, elongation method could more useful to estimate the surface tension of lithography and intaglio inks than any other methods.

• 한국인쇄학회지
• /
• 제12권1호
• /
• pp.13-27
• /
• 1994

Litho printing ink vehicles based on rosin modified phenolic are faster drying, have better durability, are harder and glosser and have greater resistance to water than ones based on ester gums. Ink-Water balance and rheological properties are important in litho printing process. These physical properties is concerned with molecular weight of Resin to use vehicle. So this paper was studied about the effects of changing molecular weight of Rosin modified phenolic on surface tension, viscosity, pseudoplasticity and printablility of Litho Inks. The results were as follows. 1) The surface tension of model inks depended on the molecular weight of the resin : Dispersion componnent of ink increase but non dispersion component decrease as molecular weight of Resin increase. 2) Water pick-up of litho ink is more fast balance, using low molecular weight of Resin. 3) Viscosity, Yield value and Newtonian value of model inks increase as molecular weight of Resin increase. 4) The litho ink prepared with the modified phenolic of which molecular weight is about 20000 showed the highest printing density and gloss.

• 한국인쇄학회지
• /
• 제12권1호
• /
• pp.145-157
• /
• 1994

Litho printing ink vehicles based on rosin modified phenolic are faster drying, have better durability, are harder and glosser and have greater resistance to water than ones based on ester gums. Ink-Water balance and rheological properties are important in litho printing process. These physical properties is concerned with molecular weight of Resin to use vehicle. So this paper was studied about the effects of changing molecular weight of Rosin modified phenolic on surface tension, viscosity, pseudoplasticity and printability of Litho Inks. The results were as follows. 1) The surface tension of model inks depended on the molecular \veight of the resin : Dispersion componnent of ink increase but non dispersion component decrease as molecular weight of Resin increase. 2) Water pick-up of litho ink is more fast balance, using low molecular weight of Resin. 3) Viscosity, Yield value and Newtonian value of model inks increase as molecular weight of Resin increase. 4) The litho ink prepared with the modified phenolic of which molecular weight is about 20000 showed the highest printing density and gloss.

• 한국인쇄학회지
• /
• 제22권2호
• /
• pp.23-36
• /
• 2004

The surface tension method has been possible only for the low viscosity materials. However, the inks for the off-set lithography and intaglio should have high viscosity and high tack. In this paper, we propose the elongation method to estimate the surface tension of high viscosity printing inks. The elongation method could be more useful to estimate the surface tension and shown in this research, it is possible to calculate the surface tension of high viscoxity ink without diluting the sample.

• 펄프종이기술
• /
• 제44권4호
• /
• pp.91-98
• /
• 2012

This study was carried out in order to evaluate the effects of ultra fine precipitated calcium carbonate (UFPCC) on properties of coating color, coated paper and off-set printability. It was found that blending of UFPCC increased the low-shear viscosity and water retention of coating color. The smaller the particle size, the more significant the effect of it. When the blending ratio of UFPCC was increased, brightness, whiteness and opacity of the coated paper were improved, while paper gloss was decreased due to the increase in roughness. When the UFPCC with the average particle size of $0.12{\mu}m$ was used, the ink receptivity during off-set printing was improved while print gloss was maintained or a little decreased. It was also observed that the dry-pick and wet-pick strength of coated paper were improved by the use of UFPCC. In conclusion, it is possible to produce the low gloss matt paper with the use of UFPCC since it could improve the optical properties and ink receptivity of coated paper.

• 한국인쇄학회지
• /
• 제21권1호
• /
• pp.71-80
• /
• 2003

Printing inks are mainly composed of pigment and vehicles. Among these components, the Vehicle affect the rheologic property of the ink the most but pigment content or characteristic also affect to the fluidity property not less than the vehicle. In the study, with the same vehicle on each sample, by making the sample to increase pigment content gradually. It can be examined the influence of the pigment to the fluidity of ink. In result we found that the viscosity value of the low shear rate rang has relatively higher value with increasing the pigment content in the ink. According to higher pigment content, yield stress and thixotropy index increases gradually. Structure recovery of the ink is that, the higher pigment content's ink, the less changing shear rate, and it takes less time to recover.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.329-329
• /
• 2008

Silver nanoparticles were synthesized by polyol process and its particle size observed with TEM is about 20nm. Silver nanoparticle ink with metal content of 30wt% was prepared using solvent of ethanol and has low viscosity of 5cps (10rpm). This ink was printed by as ink-jet printer on Al2O3 and Silicone substrate. The resistivity and morphology of the printed film was investigated as a function of sintering termperature.