• Journal of Astronomy and Space Sciences
• /
• v.28 no.1
• /
• pp.55-62
• /
• 2011

The precise orbit determination (POD) of low earth orbiter (LEO) has complied with its required positioning accuracy by the double-differencing of observations between International GNSS Service (IGS) and LEO to eliminate the common clock error of the global positioning system (GPS) satellites and receiver. Using this method, we also have achieved the 1 m positioning accuracy of Korea Multi-Purpose Satellite (KOMPSAT)-2. However double-differencing POD has huge load of processing the global network of lots of ground stations because LEO turns around the Earth with rapid velocity. And both the centimeter accuracy and the near real time (NRT) processing have been needed in the LEO POD applications--atmospheric sounding or urgent image processing--as well as the surveying. An alternative to differential GPS for high accuracy NRT POD is precise point positioning (PPP) to use measurements from one satellite receiver only, to replace the broadcast navigation message with precise post processed values from IGS, and to have phase measurements of dual frequency GPS receiver. PPP can obtain positioning accuracy comparable to that of differential positioning. KOMPSAT-5 has a precise dual frequency GPS flight receiver (integrated GPS and occultation receiver, IGOR) to satisfy the accuracy requirements of 20 cm positioning accuracy for highly precise synthetic aperture radar image processing and to collect GPS radio occultation measurements for atmospheric sounding. In this paper we obtained about 3-5 cm positioning accuracies using the real GPS data of the Gravity Recover and Climate Experiment (GRACE) satellites loaded the Blackjack receiver, a predecessor of IGOR. And it is important to reduce the latency of orbit determination processing in the NRT POD. This latency is determined as the volume of GPS measurements. Thus changing the sampling intervals, we show their latency to able to reduce without the precision degradation as the assessment of their precision.

• Journal of Korean Society for Atmospheric Environment
• /
• v.16 no.3
• /
• pp.211-223
• /
• 2000

The atmospheric dispersion of a pollutant emitted from a hypothetical source located in the middle of the Yochon Industrial Estate was simulated by using the Regional Atmospheric Modeling System (RAMS). Four horizontally nested grids were employed: the coarsest one covered the southern part of the Korean Peninsula including Mt. Chiri and the finest one covered the Yochon Industrial Estate and the surrounding area. Wind fields were initially assumed horizontally homogeneous with a wind speed of 4m/s, the average for the Yosu area, and were developed without both external forces and diurnal changes in order to investigate the terrain-induced phenomena. Wind directions that could emphasize the terrain effects on the pollutant transport and that could carry pollutants to a highly-popluated area were selected for the dispersion study. A pollutant was released for 24hours from a grid-base volume source after a 24-h blank run for developing the wind field. The dispersion study showed that the pollutant from the present source location did not directly affect the Yosu City, but showed high concentrations at locations behind the hills 5 to 6 km away from the source according to wind directions. When the wind speed was low, close to calm condition, the pollutant was detected at upstream locations 6 to 7 km from the source. In comparison with the results from the RAMS simulation, the Industrial Source Complex Short-Term Model(ISCST3) predicted a narrow dispersion that was sensitive to the wind direction. When the wind velocity was affected by the local environment, the ISCST3 calculation using that data also gave a lop-sided result, which was different from the distribution of the pollutant reproduced by RAMS.

• Journal of KIISE:Computing Practices and Letters
• /
• v.12 no.6
• /
• pp.339-348
• /
• 2006

Recently, many researches on detecting and responding worms due to the fatal infrastructural damages explosively damaged by automated attack tools, particularly worms. Network service vulnerability exploiting worms have high propagation velocity, exhaust network bandwidth and even disrupt the Internet. Previous worm researches focused on signature-based approaches however these days, approaches based on behavioral features of worms are more highlighted because of their low false positive rate and the attainability of early detection. In this paper, we propose a Distributed Worm Detection Model based on packet marking. The proposed model detects Worm Cycle and Infection Chain among which the behavior features of worms. Moreover, it supports high scalability and feasibility because of its distributed reacting mechanism and low processing overhead. We virtually implement worm propagation environment and evaluate the effectiveness of detecting and responding worm propagation.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.12 no.4
• /
• pp.210-214
• /
• 2002

The crystallization behavior of amorphous silicon (a-Si) film was investigated by using Cu-field aided lateral crystallization (Cu-FALC) process below $450^{\circ}C$. The lateral crystallization was induced from the Cu deposited region outside of pattern toward the Cu-free region inside of the pattern by applying an electric field during heat treatment. As expected, the lateral crystallization toward Cu-free region proceeded from negative toward positive electrode side. The occurrence of Cu-FALC phenomenon was interpreted in terms of dominant diffusing species in the reaction between Cu and Si. Even at the annealing temperature of $350^{\circ}C$, the large dendrite-shaped branches were formed in the crystallized region and the polarity in the lateral crystallization was clearly observed. Consequently, we could successfully crystallize the a-Si at the temperature as low as $350^{\circ}C$ by an electric field of 30 V/cm with fast crystallization velocity of 12 $\mu$m/h.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.05a
• /
• pp.267-274
• /
• 2009

Breakup and spray formation of pressure-swirl liquid jets injected into a low-speed convective-flow are experimentally investigated. Effects of the cross-flows on the macroscopic and microscopic spray parameters are optically measured in terms of jet Weber number and liquid-to-gas momentum ratio. The liquid stream undergoes Rayleigh jet breakup at lower jet Weber numbers and a liquid sheet isn't formed because of the weak radial velocity in the swirl jet. At higher jet Weber numbers, the macroscopic spray parameter is a very weak function of the momentum ratio but the effect of the convection on the microscopic spray parameter is significant through the secondary breakup with increasing in the liquid-to-gas momentum ratio. The convective-flow promotes bag/plume breakup and the spray formation, and its effect is more distinct at higher momentum ratio.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.20 no.3
• /
• pp.266-271
• /
• 1991

The salted and dried mullet roe was manufactured by the conventional processing method. The processing conditions were the salting with soybean sauce of 10% NaCl, 1.2cm of thickness, 3m/sec of air velocity, 70% of RH and $20^{\circ}C$ of wind-drying temperature for 20 days. The fractional compositions of free and bound lipids were classified in neutral, Glyco - and phospholipids of the processed roe. The fatty acid content of glycolipids was measured during processing and storage. Major fatty acids of glycolipids were $C_{16:0},\;C_{18:1}\;and\;C_{18:2}$ whose total amount was 7.71mg/100mg occupying 77% of the total fatty acids of glycolipids. The ratio of unsaturated fatty acid to the saturated fatty acid of bound glycolipids was 2.09 and that of free glycolipids was as low as about 0.92. The rations of the polyenoic acids to the monoenoic acids were very low as 0.10-0.78. The essential fatty acids of bound glycolipids were 4.32mg/100mg and a very much decreased content of 1.46mg/100mg at 9 week storage time.

• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.764-769
• /
• 2001

Recently, according to increase in the requirement of electric power, a thermoelectric power plant equipped with pulverized coal combustion system is highly valued, because coal has abundant deposits and a low price compared with others. For efficient use of coal fuel, most of plant makers are studying to improve combustion performance and flame stability, and reduce pollutant emission. One of these studies is how to control the profile of particle injection and velocity dependant on coal nozzle. Basically, a mixed flow of gas and particle in coal nozzle is required to have appropriate injection and concentration distribution at exit to achieve flame stability and low pollutant, but it is very difficult to obtain that without help of a coal separating device within nozzle. In this study, each distribution of air and coal flow rate is measured for the coal nozzle with coal separator developed by us. The coal concentration at exit is various according to inlet swirl values and positions of coal separator. Also pressure drop is measured for various operating conditions of this nozzle. From these results, we can find the separation characteristic of new developed coal separator, and select proper operation range of coal nozzle. When this coal nozzle is applied to actual plant, these investigations will be very useful to confirm the shape of coal separator to have efficient particle injection.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.17 no.8
• /
• pp.683-692
• /
• 2007

Recently, plastic products in air-intake parts of automotive engines have become very popular due to advantages that include reduced weight, constricted cost, and lower intake air temperature. However, flow-induced noise in air-intake parts becomes a more serious problem for plastic intake-manifolds than for conventional aluminum-made manifolds. This is due to the fact that plastic manifolds transmit more noise owing to their lower material density. Internal aerodynamic noise from an idle speed control actuator(ISA) is qualitatively analyzed by using a scaling law, which is expressed with some flow parameters such as pressure drop, maximum flow velocity, and turbulence kinetic energy. First, basic flow characteristics through ISA passage are identified with the flow predictions obtained by applying computational fluid dynamics techniques. Then, the effects on ISA passage noise of each design factors including the duct turning shape and vane geometries are assessed. Based on these results, the preliminary low noise design for the ISA passage are proposed. The current method for the prediction of internal aerodynamic noise consists of the steady CFD and the scaling laws for the noise prediction. This combination is most cost-effective, compared with other methods, and therefore is believed to be suited for the preliminary design tool in the industrial field.

• Journal of the Ergonomics Society of Korea
• /
• v.29 no.4
• /
• pp.681-686
• /
• 2010

Although the height of a ramp is an important design element, it has not been considered in prior studies. Therefore, in this study, the ramp slope and height are considered as independent variables. To analyze the effects of the slope and height, five levels of slope (1:6, 1:8, 1:10, 1:12 and 1:14) and three levels of height (15cm, 30cm and 45cm) are considered. For the dependent variables, the total time, velocity and perceived discomfort were considered as usability measures, pulse rate changes and EMG signals of four related muscles (extensor carpi radialis, triceps brachii, anterior deltoid and posterior deltoid) were considered as physiology measures. As a result, differences among usability and physiological characteristic for the five slopes increased as the height increased. Additionally, slope effects were minor when the height was low (15cm). Almost domestic/international regulations and guidelines related to ramp recommended 1:12 slope for the ramp design, however, there was no significant difference between 1:10 and 1:12 according to result of this study. In addition, slope effects were minor at a low height; thus, a slope of 1:8 can be recommended if the installation space for a gentler ramp is not sufficient.

• Geophysics and Geophysical Exploration
• /
• v.12 no.2
• /
• pp.199-207
• /
• 2009

From 329 earthquake data in the Korean Peninsula, we separated the intrinsic and scattering quality factor ($Q_i^{-1}$ and $Q_s^{-1}$) using the Multiple Lapse Time Window Analysis (MLTW) method. For the homogeneous velocity structure, $Q_i^{-1}$ reduces the amplitudes of both direct and coda waves; $Q_s^{-1}$ diminishes the direct wave amplitude but enlarges the coda wave amplitude. Based on this phenomenon, MLTW method analytically derives theoretical curves and obtains $Q_i^{-1}$ and $Q_s^{-1}$ by least square fit with observation curves. This study is the first approach for the seismic stable region by MLTW method, and show that $Q_i^{-1}$ and $Q_s^{-1}$ in the Korean Peninsula are very low at lower than frequencies of 5 Hz. This low value seems to be related to the inactive tectonism of the Korean Peninsula.