• Transactions of the Korean Society of Mechanical Engineers
• /
• v.10 no.5
• /
• pp.635-644
• /
• 1986

A Compuressible turbulent boundary layer effect of the high temperature, accelerating gas flow through the De-Laval nozzle on combustion chamber pressure is numerically investigated. For this purpose, the coupled momentum integral equation and energy integral equation are solved by the Bartz method, and 1/7 power law for both the turbulent boundary layer velocity distribution and temperature distribution is assumed. As far as the boundary layer thicknesses are concerned, we can obtain reasonable solutions even if relatively simple approximations to the skin friction coefficient and stanton number have been used. The effects of nozzle wall cooling and/or mass flow rate on the boundary layer thicknesses and the combustion chamber pressure are studied. Specifically, negative displacement thickness is appeared as the ratio of the nozzle wall temperature to the stagnation temperature of the free stream decreases, and, consequently, it makes the combustion chamber pressure low.

• Journal of Mechanical Science and Technology
• /
• v.19 no.5
• /
• pp.1087-1094
• /
• 2005

This paper presents the validity and limitation of the thin-shell approach for the analysis of elastic wave propagation in a pipe with nonviscous liquid. The phase velocities calculated by the thin-shell approach were compared with those calculated by the thick-cylinder approach. In contrast to the case of the empty pipe, where only two modes were obtained and the first mode was calculated in a limited frequency range, the results for the liquid-filled pipe exhibits a large number of modes due to the large number of branches of the apparent liquid mass. Several of the lowest modes of the waves in a liquid-filled pipe were calculated for various pipe thicknesses in a low frequency range. The thin-shell approach was valid for a reasonable range of pipe thicknesses.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.45 no.1
• /
• pp.45-54
• /
• 2003

The effects of binder content and silica sand content on the durability characteristics of lightweight polymer concretes are examined. As a result, the flame lingering times using unsaturated polyester resin and non-combustible polyester resin were 60∼120 and 0∼4 seconds respectively, and the combustion lengths were 9∼11 mm and 0∼3 mm, respectively. Thus it is believed that the lightweight polymer concrete was incombustible and the light weight polymer concrete in which non-combustible material was added was perfectly non-combustible. The percent of original mass of lightweight polymer concrete, according to the freezing-thawing experiment, was below 0.3 %, which was much less than that of cement concrete. The pluse velocity, for the case of the binder content 28 %, showed the minimum decreasing rate for the lightweight polymer concrete with silica sand content of 50 %. The higher the binder content, the greater the durability. That is much higher than other material and believed that the freezing-thawing was suppressed by a low absorption.

• Journal of the korean Society of Automotive Engineers
• /
• v.4 no.2
• /
• pp.58-68
• /
• 1982

It is well known to diesel engineers that the heat release pattern is one of the most important factors affecting engine performance. Thorough research in heat release pattern has materially helped the progress in high-speed diesel engine development . This paper is based on the research conducted at KAIST and Daewoo Heavy Industry last year. The purpose of this paper is to determine the heat release pattern in combustion chamber of MAN M type, the famous low-noise engine. Thermodynamic cycle simulation was performed using Whitehous-Way's heat release pattern with modified coefficients and Annand's heat transfer model. Instantaneous temperature and pressure of gas in cylinder could be determined by the numerical solution of simultaneous equation of mass conservation, equation of energy conservation, and state equation of ideal gas. Calculated results were compared with measured values in some details emphasizing upon the factors affecting rate of heat release. The agreement was fairly good and revealed why M type should have lower burning velocity at the early part of combustion in spite of high injection rate. Additional results by parametric studies were given in relation to fuel injection conditions for further application to engine development.

• Proceedings of the Korea Society of Environmental Biology Conference
• /
• 2004.05a
• /
• pp.24-24
• /
• 2004

This study was investigated to the seasonal variation of attached diatoms communities in the Hantan River in November 2001, February, Ma and August 2002. It was identified the total 107 taxa which were composed of 95 species, 11 varieties and 1 unidentified speCies. The standing crops ranged 298,5004,776,000cells${\cdot}cm^{-2}.$and showed marked irregularly seasonal variations. It was higher value at the lower station than the upper station in fall. But it was similar values from the upper to the lower station by the effect of typhoon in summer. Chlorophyll concentrations ranged $13.4~304.2{\mu}m{\cdot}cm^{-2}.$ Standing crops and chlorophyll showed similar trends during investigation. Low diversity index values probably indicated the effects of envi~onmental stresses(water temperature, flow and current velocity) other than organic pollution. An assessment of organic pollution using epilithic diatoms(DAlpo) was $\alpha$-oligosaprobic states at the upper and mid stations, and was $\alpha$-mesosaprobic states at the lower stations.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2001.11a
• /
• pp.27-34
• /
• 2001

A new functionally gradient metal coating method using an atomic mixing technique was developed. In this work the effect of silver atomic mixing on the tribological characteristics of silver$.$ films. has been investigated experimentally. Atomic mixing was implemented by using the, bombardment .of accelerated Ar ions during the thermal evaporation coating process of silver films. Experiments were performed in dry conditions using a ball-on-disk test rig at a load range of 19.6 mN - 17.64 N and a sliding velocity of 20 mm/sec. Results showed that the life of functionally gradient silver coating was enhanced about 100 times more than that of thermally evaporated silver coating and 2 times more than that of IBAD silver coating. The functionally gradient. film also showed low friction and wear compared to those of the evaporated silver and

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1997.04a
• /
• pp.42-48
• /
• 1997

The dynamic response of symmetric cross-ply and angle-ply composite laminated plates under impact loads is investigated using a higher order shear deformation theory. A modified Hertz law is used to predict the impact loads and a four node finite element is used to model the plate. By using a higher order shear deformation theory, the out-of-plane shear stresses, which can be a crucial factor in the failure of composite plates, are determined with significant accuracy. The results compared with previous investigations showed good agreement. The effect of ply sequence and ply angle on the contact force is also studied.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2004.05b
• /
• pp.376-380
• /
• 2004

측벽이 존재하는 개수로 난류흐름에 대한 DNS 자료를 이용하여 난류의 비등방성을 해석하였다. 측벽의 2등분선(sidewall bisector)에서 난류강도의 분포를 통해 바닥과 자유수면에서의 비등방성을 분석하고, AIM을 도입하여 흐름장 전반에 걸쳐 세부적인 비등방성 해석을 수행하였다. 측벽의 2등분선에서의 난류강도의 분포를 통해 바닥과 자유수면 근처에서 난류강도가 강한 비등방성을 갖는 것을 볼 수 있었다. 또한 3개의 다른 영역에서 AIM의 도입을 통해 측벽이나 바닥근처에서는 난류의 비등방성이 구형 관수로 흐름과 유사한 것으로 나타났으나, 개수로 난류흐름의 주된 특성이 velocity-dip phenomena가 존재하는 영역에서는 구형 관수로 흐름과는 달리 천이영역이 존재한다는 것을 알 수 있었다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.144-144
• /
• 2011

Diagnostics of plasma density and temperature play an important role for monitoring plasma processing and Laser Thomson scattering is a one of the most accurate diagnostic technique for measuring plasma density and temperature because of none-perturbation to plasma among various diagnostic techniques invented to measure plasma density and temperature. I will briefly review Laser Thomson scattering experiment performed in KRISS and difficulties for measuring the electron velocity distribution such as Gaussian due to low signal-to-noise ratio with showing results that we got until now. This work is an intermediate step in a process that we will get a reliable data which shows physical phenomenon of plasma compared with other diagnostic techniques and results.

• Korean Journal of Ecology and Environment
• /
• v.44 no.1
• /
• pp.66-74
• /
• 2011

This numerical study aims to investigate the effect of cohesive sediment on turbulence structure due to density stratification. The transport model for cohesive sediment incorporated with flocculation model has been selected and calculates the concentration, fluid momentum, and turbulence. From the model results, it is known that suspension of sediment decreases turbulence intensity. It is also found that cohesive sediment has a relatively weak effect on turbulence damping compared to noncohesive sediment. The low settling velocity and more suspension of cohesive sediment are considered to be mechanisms of this behavior. Richardson number determined with results of this study quantitatively shows that cohesive sediment causes less stable density stratification condition and, as a result, the turbulence structure is less damped compared to the case of noncohesive sediment.