• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.628-633
• /
• 2001

This paper presents analysis of the flows through three different types of radial compressor by using quasi-three-dimensional analysis method. The method obtains two-dimensional solution for velocity distribution on meridional plane, and then calculates approximately the static pressure distributions on blade surfaces. Finite difference method is used for the solutions of governing equations. The compressors have low level compression-ratio and 12 straight radial blades with no sweepback. The results are compared with experimental data and the results of inviscid analysis with finite element method. It can be concluded that the agreement is good for the cases where viscous effects are not dominant.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.836-839
• /
• 2003

A pneumatic servo valve which is widely applied in industrial field. And It is consist of force motor, spool ＆ sleeve and servo controller. In this study. we developed the force motor which is consume to low power for a pneumatic servo valve. We could reduce the number of turn of the solenoid by using ferromagnetic permanent magnet and took different direction of each other using one coil instead of two coil. we modeled a system consisting of various electro-mechanical subsystems. The appropriateness of the model was verified by simulation. The simulation model resolved the motion of spool, the winding current and the magnetic force. Also, we calculated the displacement and velocity of the spool, flux contour line, b vector. flux density. flux linkage, back EMF etc.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.13 no.6
• /
• pp.114-118
• /
• 2004

This research focused on the principle and the development of continuous regeneration DPF technology which was the best particulate matters removing technology of current existing technologies owing to its superior comparability and possible applicability. In addition, there were some discussions about the affecting engine parameters such as engine driving conditions and the amounts, velocity, temperature, pressure of exhaust emissions as well as sulfur contents and lubricants which were prerequisites to prevent poisoning effect on catalysts. The test was made on an 8000cc heavy-duty turbo diesel engine on which continuous regeneration DPF was in order to investigate regeneration characteristics of DPF and me performance under the condition of standard or 50ppm low sulphur diesel. Exhaust emissions, CO, HC, NOx PM were measured and compared under D-13 modes.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.17 no.6
• /
• pp.28-34
• /
• 2008

Mg alloy is widely used for the IT, auto and consumer electronics industries. Semi-solid casting(SSC) of magnesium alloys is used to produce high quality components. SSC process is analogous with the injection molding of plastics. The high strength and low weight characteristics of magnesium alloys render the high-precision fabrication of thin-walled components with large surface areas. To produce thin-walled magnesium alloy parts, SSC process parameters on the quality of the finished product should be clearly studied. In this paper, to select optimal process parameters, Taguchi method is applied to the optimal design of the process parameters in the SSC process. The die temperature, injection velocity and barrel temperature of the SSC process are selected for the process parameters. The effectiveness of the optimal design is verified through the CAE software.

• Journal of KSNVE
• /
• v.8 no.5
• /
• pp.807-813
• /
• 1998

Transmission loss of the simple expansion chamber with multiple inlet and outlet ports is obtained. Transfer matrices which represent the relation between the power variables(pressure and velocity) of inlets and outlets depend on the input relatons as well as the acoustic system parameters(i.e. geometry of the chamber, wall admittance, etc.). The analysis has been performed analytically, including the effects of higher order modes for the 2-inlet/1-outlet, 1-inlet/2-outlet and 2-inlet/2-outlet systems. This study yeilds that phase difference between the inlet ports can significantly increase the transmission loss in low frequency range.

• Membrane and Water Treatment
• /
• v.1 no.2
• /
• pp.159-169
• /
• 2010

The effect of external recycle on the performance of dialysis in countercurrent-flow rectangular membrane modules was investigated both theoretically and experimentally. Theoretical analysis of mass transfer in parallel-flow device with and without recycle is analogous to heat transfer in parallel-flow heat exchangers. Experiments were carried out with the use of a microporous membrane to dialyze urea aqueous solution by pure water. In contrast to a device with recycle, improvement in mass transfer is achievable if parallel-flow dialysis is operated in a device of same size with recycle which provides the increase of fluid velocity, resulting in reduction of mass-transfer resistance, especially for rather low feed volume rate.

• Journal of ILASS-Korea
• /
• v.11 no.1
• /
• pp.39-47
• /
• 2006

In-cylinder flows in a motored 3.5L four-valve SI engine were investigated quantitatively using three-component LDV system, to determine how engine configuration affects the flow field. The purpose of this work was to develop quantitative methods which correlate in-cylinder flows to engine performance. For this study, two distinct intake/piston arrangements were used to examine the flow characteristics. Quantification of the flow field was done by calculating two major parameters which are believed to characterize adequately in-cylinder motion. These quantities were turbulent kinetic energy(TKE) and tumble ratio in each plane at each crank angle. The results showed that in-cylinder flow pattern is dominated by the intake effects and two counter rotating vortices, developed during the intake stroke, produced relatively low tumble ratio. Therefore, the applicability of these quantities should be carefully considered when evaluating characteristics resulting from the complex in-cylinder flow motions.

• Journal of ILASS-Korea
• /
• v.19 no.4
• /
• pp.167-173
• /
• 2014

The spray characteristics of Gas-Centered Swirl Coaxial Injector was investigated that there were different characteristics with or without gas flow. As gas flow was accelerated, the momentum of gas was transferred to the momentum of liquid in the low liquid Reynolds number. Therefore, the axial velocity of liquid was increased and the measured value was smaller than without gas flow. However, in the high momentum flux ratio, the momentum transfer hardly occurred and the results had constant values. As the recess length was increased, the mixing area of gas and liquid also was increased, the results were decreased.

• 제어로봇시스템학회:학술대회논문집
• /
• 1992.10a
• /
• pp.387-392
• /
• 1992

This paper presents a local trajectory generation method which is based on a sequence of reference posture-velocities and the efficient low level control algorithm which constructs the complete smooth curve from the trajectory specification. The reference trajectory generator(RTG) which is in between the local path planner(LPP) and the robot motion controller(RMC) generates a sequence of set-points for each path segments from the LPP and pass it to the RMC. The RMC controls the motions of vehicle which should follow the sequence. In the feedback controller of VMC, the method which compensates robot posture-velocity error correctly is used. These methods are implemented on indoor autonomous vehicle, 'ALIVE' mobile robot. The ALIVE mobile robot system is implemented on the 32bit VME bus system: the two VME CPU's are used for RTG and RMC, while the 80C196KC-based VME board is used for motor controller.

• Journal of Institute of Control, Robotics and Systems
• /
• v.16 no.11
• /
• pp.1096-1103
• /
• 2010

This paper proposes CDC (Continuous Damping Control) algorithm and verifies in multi-body dynamic vehicle. In order to distinguish a road profile on driving, waviness calculated by the filtered vertical-accelerations of sprung and unsprung masses is introduced. Sky-hook control is used at a low waviness road and constant damping level control is used at a high waviness road, where the hard damping level is determined by waviness, roll rate, acceleration, and deceleration. The damping levels of ride, anti-roll, anti-squat, and anti-dive modules are calculated by tuning parameters which is dependent upon vehicle velocity. Therefore this high tunable algorithm is useful to improve the ride and handling performance under various driving conditions. In the simulations, tire and dampers are modelled by SWIFT (Short Wavelength Intermediate Frequency Tire) model and 1st order delay model, and results are compared with conventional damper's.