• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.7
• /
• pp.17-25
• /
• 1999

Tungsten nitride($WN_x$) films were deposited by PECVD method on silicon nitride($WSi_3N_4$) substrate. The characteristics of $WN_x$ film were investigated with changing various processing parameters ; substrate temperature, gas flow rate, rf power, and different nitrogen sources. The nitrogen composition in $WN_x$ film varied from 0 to 45% according to the $NH_3$ and $N_2$ flow rate. The highest deposition rate of 160 nm/min was obtained for the $NH_3$ gas and relatively low deposition rate of $WN_x$ films were formed by $N_2$ gas. $WN_x$ films deposited on $WSi_3N_4$ substrate had higher deposition rate than that of TiN and Si substrates. The purity of $WN_x$ film were analyzed by AES and higher purity $WN_x$ films were deposited using $NH_3$ gas. The XRD analysis indicates a phase transition from polycrystalline tungsten(W) to amorphous tungsten nitride($WN_x$), showing improved etching profile of $WN_x$ films Thick $WN_x$ films were deposited on various substrates such as Tin, NiCr and Al and maximum thickness of $1.6 {\mu}m$ was obtained on the Al adhesion layer.

• Journal of Environmental Health Sciences
• /
• v.46 no.2
• /
• pp.192-203
• /
• 2020

Objectives: The concentration distributions of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs), dioxin-like polychlorinated biphenlys (dl-PCBs), and polycyclic aromatic hydrocarbons (PAHs) in fine particles were investigated to provide basic data on POP behavior and composition analysis. Methods: The concentrations of PCDD/Fs, dl-PCBs, and PAHs by particle size were evaluated for TSP, PM₁₀, and PM_2.5. Also, fine dust component analysis and factor analysis were performed to identify the source of PCDD/Fs. Results: The particle size distribution was found to account for 24.3% of >10 ㎛, 14.5% of 2.5-10 ㎛, and 61.2% of <2.5 ㎛. The average contributions of coarse particles (>2.5 ㎛) and fine particles (<2.5 ㎛) were PCDD/Fs 67%, dl-PCBs 66%, benzo (a) pyrene 83% and PAHs 84%, and the contributions of fine particles (<2.5 ㎛) were higher than coarse particles (>2.5 ㎛). However, the contributions of coarse particles increased in April to September with higher temperatures, while those of fine particles increased in February to March with lower temperatures. Conclusions: Low chlorinated (4Cl-5Cl) PCDD/Fs were more adsorbed compared to coarse particles due to the influence of pollutant migration from particulate to gas phase according to temperature rise, whereas high chlorinated (6Cl-8Cl) PCDD/Fs were more adsorbed compared to fine particles. PCDD/Fs sources were assessed to be major sources of emissions, such as incineration facilities and/or open burning.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.2 no.1
• /
• pp.55-59
• /
• 1973

This experiment was carried out to improve on the simple and conventional processing method by studying the characteristics of poultry meat. For the experiment, 20 hens culled and 20 broilers were slaughtered and divided into the following five groups; whole carcass, skinned carcass, debonned carcass, thigh muscle and breast muscle. Each group was ground by the super grinding machine. The results tobtained are summarized as follows; (1) The percentage of the ready-to-cook of cull hens and broilers was $64.32{\pm}2.11,\;67.96{\pm}1.16$, and of the water uptake, $105.43{\pm}1.9,\;104.13{\pm}0.2$, respectively. (2) In the chemical composition, broiler meat showed high moisture content and a little low fat content, as compared with cull hen meat. By groups, whole carcass ground meat contained lower maisture content, and higher fat and ash content than thigh muscle and breast muscle. (3) Thigh muscle and breast muscle group was higher than the other and whole carcass group was lower for the relative WHC and water retention.(4) The higher temperature the higher cooking loss percentage in all groups, and whole carcass group was the highest cooking loss percentage among the all groups.(5) The significant difference was little observed for the relative WHC, water retention and cooking loss percentage by groups between cull hen and Broiler.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.45 no.3
• /
• pp.215-223
• /
• 2012

This study was conducted to prepare canned skipjack tuna Katsuwonus pelamis in the mixture of isotonic beverage and tomato paste (ST-S) for use as a health food. An analysis of the time-temperature profile and viable cells showed that a reasonable F0 value for ST-S preparation was 4 min. The proximate composition of ST-S was 76.8% moisture, 20.2% crude protein, 0.8% crude lipid, 1.7% ash and 0.5% carbohydrate. The calorie content of ST-S was 94.8 kcal, which is 47.4% lower than that of commercial canned skipjack tuna in oil (ST-O) and 2.2% lower than that of commercial chicken breast in water (CB-B). The total amino acid content of ST-S was 18.54 g/100 g, which is 31.4% lower than that of ST-O and 7.9% lower than that of CB-B. The major amino acids in ST-S were aspartic acid and glutamic acid. An enrichment effect due to such minerals as phosphorus, potassium and iron would be expected on consuming 100 g of ST-S. The major fatty acids in ST-S were 16:0 (27.4%), 18:1n-9 (14.3%) and 22:6n-3 (27.8%), which are different from those in ST-O and CB-B. The major free amino acids in ST-S were glutamic acid (8.1%), histidine (38.6%) and its related dipeptide, such as anserine (15.7%). In an evaluation of taste, flavor and color, ST-S was found to be superior to ST-O and CB-B.

• The Korean Journal of Petroleum Geology
• /
• v.6 no.1_2 s.7
• /
• pp.37-43
• /
• 1998

Chemical components of water, chemical and isotopic compositions of extractable gases were analyzed to characterize the properties of the natural gases which are dissolved in ground water in the Pohang area. Amount of total extracted gases ranges from 27 ml/l to 50.1 ml/l. Hydrocarbon gases are composed of methane ($27{\~}376,420 ppm$) and ethane ($19{\~}127 ppm$). Amount of total hydrocarbon gases is related to the lithology and geological factors around the reservoir. Quantity of hydrocarbon gases tends to increase in the Tertiary reservoirs and in the reservoirs where the Tertiary formations are thick enough. According to the relationship between hydrocarbon gases and total solids in the ground water, it is believed that the hydrocarbon gases were dissolved in the Tertiary formation water. Based on the methane content ($>99.9\%$) and isotopic composition (${\delta}C^{13};-73.1\%_{\circ}{\~}-43.22\%_{\circ}$), we interpret the gases to be of predominantly biogenic origin which were generated by the methanogenic bacterial processes under the low temperature and anoxic conditions.

• Journal of the Korean Applied Science and Technology
• /
• v.30 no.1
• /
• pp.35-48
• /
• 2013

Biodiesel is an alternative diesel fuel which can be obtained from the transesterification of vegetable oils, animal fats and waste cooking oil. The objective of this study is to evaluate the properties of biodiesel obtained from different feedstocks (soybean, waste cooking, rapeseed, cottonseed and palm oils). The biodiesel derived from different feedstocks was analyzed for FAME (fatty acid methyl esther) content, kinematic viscosity, flash point, CFPP (cold filter plugging point) and glycerin content. The quality of biodiesel was tested according to the Korean and European standard (EN14214, requirements and test method for biodiesel fuel). The biodiesels derived from soybean, waste cooking, rapeseed and cottonseed oils contain high amount of unsaturated fatty acid, while palm biodiesel is dominated by saturated fatty acid. The fuel properties of biodiesel, such as low temperature performance, kinematic viscosity and oxidation stability are correlated with the FAME composition components in biodiesel.

• Journal of Korean Society for Atmospheric Environment
• /
• v.33 no.2
• /
• pp.87-96
• /
• 2017

In this study, 4 gases containing typical chlorinated volatile organic compounds (VOCs) were treated by ultraviolet (UV) irradiation. The typical chlorinated VOCs are dichloromethane (DCM), trichloromethane (TCM), carbon tetrachloride (CTC) and trichloroethylene (TCE). The removal efficiency (RE) and the products of chlorinated VOCs by UV irradiation are investigated. At this time, 2 types of background gas (air and nitrogen) were used to figure out the RE by photooxidation and photolysis. The specification of UV-lamp used in this study was low-pressure mercury lamp emitting wavelength of 185~254 nm. The experimental conditions were set as initial VOC concentration of $180{\pm}10ppm$, empty bed retention time (EBRT) of 53 s, temperature of $23{\pm}2^{\circ}C$ and relative humidity of $65{\pm}5%$. In the photolysis condition with nitrogen ($N_2$) as background gas, the averaged RE of the 4 types of chlorinated VOCs was about 24% higher than that with photooxidation; and the REs of VOCs except CTC were confirmed as >99%. The composition of off-gases after UV photooxidation in air was investigated and several intermediates from DCM, TCM and TCE were detected by GC/MS. Among them, phosgene which is a toxics was detected as an intermediate of TCM. In addition, the concentration of carbon dioxide ($CO_2$) in the off-gases was measured to calculate the mineralization rate (MR). With the photooxidation, TCE showed the highest RE (>99%) while MR was the lowest (17%); and the MR of DCM was the highest (86%). In addition, particulate matters (PM) in the off-gases was also detected and high concentrated $PM_{10}$ ($21,580{\mu}g{\cdot}m^{-3}$) and $PM_{2.5}$ ($6,346{\mu}g{\cdot}m^{-3}$) were detected in TCE off-gas. More than 99% of the chlorinated VOCs could be removed using UV254-185 nm lamp, while it is necessary to conduct further studies on the production and treatment of secondary pollutants.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.8 no.3
• /
• pp.627-631
• /
• 2007

The factors affecting on sludge sedimentation are reported as F/M ratio, ingredient, composition of influent substrate, dissolved oxygen concentration, temperature, pH, filamentous bacteria and SRT. Aeration tank applying Bacillus sp. has an important role for maintaining the dominant microorganism species to make steady progress for spore growth affecting sedimentation. This research aims to investigate the affecting factor for the sedimentation in B3 system and RABC system with aeration tank applying tapered aeration. Extracellular polymeric substances(EPS), protein and carbohydrate can be produced for the extreme condition, that is down to 0.2 mg/L of dissolved oxygen in the aeration tank. This research found out the relation between the sedimentation and the EPS production, especially the ratio of protein/carbohydrate. The spore of Bacillus sp. was formed at the low DO then microorganisms produced EPS. The results showed that the production of EPS was 109.95 mgEPS/gSS at 1.6 mg/L of DO, however it was 131.77 mgEPS/gSS at 0.5 mg/L of DO. The sedimentation was affected by protein content in EPS and the ratio of protein and carbohydrate. The settleability of sludge was not affected by the ratio of protein/carbohydrate in B3 process, meanwhile settleability was affected by the ratio of it in RABC process, respectively.

• Journal of Veterinary Clinics
• /
• v.11 no.2
• /
• pp.545-552
• /
• 1994

This experiment was carried out to investigate the renditions to maintain good post-thaw motility and viability of canine spermatozoa when the semen was frozen using methanol. The semen from two male dogs which had been proven to be fertile in the previous one year was treated with different compositions of semen diluent and was frozen at different freezing temperatures, When canine semen was frozen at-2$0^{\circ}C$, -6$0^{\circ}C$, or -8$0^{\circ}C$, the spermatozoa frozen and stored at -2$0^{\circ}C$ showed very low post-thaw motility and viability from day 2 to 7 and showed no viability since day 15 after freezing. The spermatozoa frozen and stored at -6$0^{\circ}C$ or -8$0^{\circ}C$ showed higher post-thaw motility and viability on day 2, 1, 15 and 30 after freezing than that frozen and stored at-2$0^{\circ}C$(p<0.01), with no difference between two groups. Among different composition groups of the semen diluents of control(tris + egg yolk + glycerol), egg yolk-free, 히ycerol-free, and tris-free, Prior to freezing, the egg yolk-free diluent showed significantly love. motility and viability than the other diluents(p<0.05). On each thawing day (from day 2 to 15 after freezing), control group showed considerably higher motility and viability than the other groups(p<0.01). The canine spermatozoa frozen and stored at -6$0^{\circ}C$ and -8$0^{\circ}C$ showed gradual decrease of motility from day 2 to 30 after freezing and the spermatozoa of these two groups thawed on day 30 showed considerably love. motility than those thawed on day 2 after freezing, respectively(p<0.01). These results indicate that the freezing temperature of either -6$0^{\circ}C$ or -8$0^{\circ}C$ can be applicable to the freezing method using methanol and also all of the components of the semen diluent including cryoprotectant, buffer and cold-shock buffer are very important to maintain motility and viability of canine spermatozoa in the freezing and thawing procedure.

• Korean Journal of Food Science and Technology
• /
• v.2 no.2
• /
• pp.61-67
• /
• 1970

The growth characteristics of Candida tropicalis KIST 359, isolated from soil samples collected at an oil depot in Korea, have been studied by cultivating batches under varying conditions. The conclusions of the study were: 1. The yeast easily assimilates hydrocarbons in a range of $C_{14}-C_{17}$, and the optimum cultivation temperature and pH are $30^{\circ}C$ and 5.5, respectively. 2. Using this strain of micro-organism, gas oil gives a higher cell yield than kerosine and with gas oil except urea all other nitrogen sources $(NH_4NO_3,\;NH_4Cl,\;(NH_4)_2SO_4\;and\;(NH_4)_2HPO_4)$ similarly support a satisfactory growth of the yeast. 3. The highest yield is obtained with a gas oil level of 10%(v/v), and concentrations of nitrogen source and $MgSO_4{\cdot}7H_2O$ of 0.5 and 0.05%(w/v), respectively. 4. The protein content of dried yeast cells is 59.8%. Its amino acid composition can be compared well with that of FAO provisional patterns, but with a low methionine and a high lysine content.