• Journal of the Korean Ceramic Society
• /
• v.36 no.6
• /
• pp.583-589
• /
• 1999

In the fabrication of ceramic chip couples for high frequency application such as the mobile communication equipment the formation of electrode lines and Ag diffusion were investigated with heat treatment conditions for removing organic binders. The deformation and densification of the electrode line greatly depended on the binder burnout process due to the overlapped temperature zone near 400$^{\circ}C$ of the binder dissociation and the solid phase sintering of the silver electrode. Ag ions were diffused into the glass ceramic substrate. The Ag diffusion was led by the glassy phase containing Pb ions rather than by the crystalline phase containing Ca ions. The fact suggests that the Ag diffusion could be controlled by managing the composition of the glass ceramic substrate.

• Journal of the Korean Ceramic Society
• /
• v.31 no.6
• /
• pp.660-670
• /
• 1994

Transparent, crack-free dried gel monoliths with a composition of LiZr1.5Si2P2O12.5 have been synthesized by the low temperature polymerization of the Sol-Gel technique using metal alkoxides as starting materials. After initial reaction (20~40 min), each metal alkoxide closely paralleled each other during the hydrolysis reactions. The safe drying conditions of gels with no creaks the control of the shrinkage rate. The gels converted into the glass by heat treatment at 75$0^{\circ}C$. FTIR data indicated that the gels were phase separated into silicarich and phosphate-rich regions with the lithium. XRD results showed the formation of crystalline LiH2PO4. The gels dried at 15$0^{\circ}C$ or fired at 75$0^{\circ}C$ contained the residual water. The high ionic conductivity at room temperature for these gels was attributed to the motion of protons.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11b
• /
• pp.537-540
• /
• 2001

This paper presents the characteristics of Ta-N thin-film for high precision resistors, which were deposited on Si substrate by DC reactive magnetron sputtering in an argon-nitrogen atmosphere(Ar-(4~16 %)$N_2$). Structural properties studied using X-ray diffraction(XRD) indicate the presence of TaN, $Ta_3N_5$ or a mixture of Ta-N phases in the films depending on the amount of nitrogen in the sputtering gas. The chemical composition are investigated by auger electro spectroscopy(AES). The optimized conditions of Ta-N thin-film resistors were deposited in 4 % $N_2$ gas flow ratio. Under optimum conditions, the Ta-N thin-film resistors are obtained a high resistivity, $\rho=305.7{\mu}{\Omega}cm$, a low temperature coefficient of resistance, TCR=-36 $ppm/^{\circ}C$.

• Electrical & Electronic Materials
• /
• v.9 no.4
• /
• pp.351-356
• /
• 1996

The quartemary system ceramics 0.5[xPb(Zn$_{1}$3/Nb$_{2}$3/)O$_{3}$-(1-x)Pb(Ni$_{1}$3/Nb$_{2}$3/)O$_{3}$]-0.5[yPbTiO$_{3}$-(1-y) PbZrO$_{3}$ for piezoelectric actuators were prepared bv the were added to the raw materials up to 5 mole. Sintering temperature was varied form 1000.deg. C to 1200.deg. C. Sintering characteristrics, dielectric and piezoelectric properties were then investigated. Piezoelectric properties of sample prepared by the molten salt method were improved compared to those prepared by the conventional method. Addition of PZN shifted morphotropic phase boundary to more Zr-rich composition and decreased the piezoelectric properties.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.1316-1317
• /
• 2006

The paper investigates the possibility to avoid extrinsic embrittlement of $Ni_3Al$, also increasing the high temperature strength, by alloying with both Fe - of a high strengthening effect and Cr - able to remove a part of diffused oxygen along the grain boundaries. As Cr homogenization in $Ni_3Al$ is difficult because of its low diffusion coefficient, for its improving a mechanical alloying (MA) step before the compound synthesis by Self-propagating High-temperature Synthesis (SHS) was adopted. The obtained better homogenization resulted in higher mechanical resistance and deformability than of the unalloyed $Ni_3A/Ni_3Al$ alloys of the same composition obtained without MA step.

• Proceedings of the Korean Society of Postharvest Science and Technology of Agricultural Products Conference
• /
• 2003.10a
• /
• pp.142.1-142
• /
• 2003

Mono-, diacylglycerol were synthesized by glycerolysis of bran oil and glycerol using IM60 (an immobilized lipase) in a stirred batch reactor for 72 hours. After glycerolysis, the composition TAG, DAG, MAG in product was 41.7%, 44.7%, and 11.1%, respectively. Glycerol was separated, then this mixture product was undergone fractionation for winterization followed. The fractionation was performed using hexane and acetone solvent to reduce palmitic acid at the low temperature for overnight individually. Temperature was set -40$^{\circ}C$, -14$^{\circ}C$, -8$^{\circ}C$ and 0$^{\circ}C$, respectively. By considering results from this experiments, fractionation with hexane at -8$^{\circ}C$ was most efficient regarding to yield without crystallization.

• Journal of the Korean Ceramic Society
• /
• v.25 no.6
• /
• pp.623-630
• /
• 1988

As a function of the composition and content of frit, the electrical property of Ag and Ag/Pd thick film conductors were investigated with microstructure. With increasing sintering temperature in Ag-frit thick film conductors, electrical sheet resistivity decreased, but again increased above 80$0^{\circ}C$. And when frit contents is 5wt%, compact and homogenious microstructure can be obtained, then electrical sheet resistivity has minimum value. In Ag/Pd-frit film conductor, the electrical sheet resistivity decreased with increasing sintering temperature. The system which having frit with low softing point has lower sheet resistivity then to add high softening point frit.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.12
• /
• pp.1034-1038
• /
• 2007

In order to develop the composition ceramics capable of being sintered at low temperature with high piezoelectric properties for multilayer piezoelectric actuator application, PZW-PMN-PZT system ceramics were manufactured according to sintering aid $Li_2CO_3$ addition and their microstructural, dielectric and piezoelectric properties were investigated. The crystal structure of the specimens showed a perovskite phase and no pyrochlore or other second phase was detected. At the sintering temperature of $900\;^{\circ}C,\;0.2\;wt%Li_2CO_3$ added specimen showed a optimum values of kp = 0.562, $d_{33}\;=\;360\;pC/N$ and Qm = 1184, respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11a
• /
• pp.537-540
• /
• 2001

This paper presents the characteristics of Ta-N thin-(ibm for high precision resistors, which were deposited oni substrate by DC reactive magnetorn sputtering in an argon-nitrogen atmosphere(Ar-(4∼16%)N$_2$). Sturcutural properties sutided using X-ray diffraction (XRD) indicate the presence of TaN, Ta$_3$N$\sub$5/ or a mixture of Ta-N phases in the films depending on the amount of nitrogen in the sputtering gas. The chemical composition are investigated by auger electro spectroscopy(AES). The optimized conditions of Ta-N thin-film resistors were deposited in 4 % N$_2$ gas flow ratio. Under optimum conditions, the Ta-N thin-film resistors are obtained a high resistivity, $\rho$=305.7 ${\mu}$Ωcm, a low temperature coefficient of resistance, TCR=-36 ppm/$^{\circ}C$.

• Journal of Korea Foundry Society
• /
• v.2 no.2
• /
• pp.18-30
• /
• 1982

For the purpose of improving the casting yields of ductile iron castings, the casting conditions for riserlese design were investigated with 150mm cube. As the important casting conditions, chemical composition, pouring temperature, mold rigidity and cooling rate were confirmed. 1. We could obtain the sound castings with the hypereutectic ductile iron. 2. In order to reduce liquid contraction, the pouring temperature should be low as much as possible 3. We could obtain the sound castings through using the rigid mold without mold cavity deformation 4. The modulus of the castings should be 2.5cm one or larger.