• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2004년도 유체기계 연구개발 발표회 논문집
• /
• pp.419-426
• /
• 2004

A three-dimensional computation was conducted to understand effects of the inlet boundary layer thickness on the loss mechanism in a low-speed axial compressor operating at the design condition(${\phi}=85\%$) and near stall condition(${\phi}=65\%$). At the design condition, the flow phenomena such as the tip leakage flow and hub comer stall are similar independent of the inlet boundary layer thickness. However, when the axial compressor is operating at the near stall condition, the large separation on the suction surface near the casing is induced by the tip leakage flow and the boundary layer on the blade for thin inlet boundary layer but the hub corner stall is enlarged for thick inlet boundary layer. These differences of internal flows induced by change of the boundary layer thickness on the casing and hub enable loss distributions of total pressure to be altered. When the axial compressor has thin inlet boundary layer, the total pressure loss is increased at regions near both casing and tip but decreased in the core flow region. In order to analyze effects of inlet boundary layer thickness on total loss in detail, using Denton's loss models, total loss is scrutinized through three major loss categories in a subsonic axial compressor such as profile loss, tip leakage loss and endwall loss.

• 대한기계학회논문집B
• /
• 제29권3호
• /
• pp.322-329
• /
• 2005

The flow characteristics in the blade passage and in the wake region of a low speed axial flow fan have been investigated by experimental analysis using a rotating hot-wire sensor for design and off-design operating conditions. The results show that the tip leakage vortex is moved upstream when flow rate is decreased, thus disturbing the formation of wake flow near the rotor tip. The tip leakage vortex interfaces with blade pressure surface, and results in high velocity fluctuation near the pressure surface. From axial velocity distributions downstream of the fan rotor, large axial velocity decay near the rotor tip is observed at near stall condition, which results in large blockage compared to that at the design condition. Although the wake flow downstream of the rotor blade is clearly measured at all operating conditions, the trough of the high velocity fluctuation due to Karmann vortex street in the wake flow is mainly observed at a higher flow condition than the design flow rate.

• 한국대기환경학회지
• /
• 제21권1호
• /
• pp.63-72
• /
• 2005

In order to understand regional wind characteristics and to estimate offshore wind resources, a wind map of the Korean Peninsula was established using remote-sensing data from the satellite, U.S. NASA Quik SCAT which has been deployed for the Sea Winds Project since 1999. According to the linear regression result between the wind map data and in-situ marine-buoy data, the correlation factor was greatly improved up to 0.87 by blending the remote-sensing data of Quik SCAT with U.S. NCEP/NCAR CDAS reanalysis data to eliminate precipitation interference and to increase temporal resolution. It is found from the established wind map that the wind speed in winter is prominent temporally and the South Sea shows spatially high energy density over the wind class 6. The reason is deduced that the north-west winds through the Yellow Sea and the north-east winds through the East Sea derived by the low pressure developed in Japan are accelerated passing through the Korea Channel and formed high wind energy region in the South Sea; the same trends are confirmed from the statistical analysis of the meteorological observation data of KMA.

• International Journal of Fluid Machinery and Systems
• /
• 제4권1호
• /
• pp.209-216
• /
• 2011

The flow upstream of a centrifugal pump impeller has been investigated by both experimental test and numerical simulation. For experimental study, the flow field at four sections in the pump suction is measured by using PIV method. For calculation, the three dimensional turbulent flow for the full flow passage of the pump is simulated based on RANS equations combined with RNG k-$\varepsilon$ turbulence model. From those results, it is noted that at both design lo ad and quarter load condition, the pre-swirl flow whose direction is the same as the impeller rotation exists at all four sections in suction pipe of the pump, and at each section, the pre-swirl velocity becomes obviously larger at higher rotational speed. It is also indicated that at quarter load condition, the low pressure region at suction surface of the vane is large because of the unfavorable flow upstream of the pump impeller.

• 전력전자학회논문지
• /
• 제3권1호
• /
• pp.23-35
• /
• 1998

영구자석 동기전동기의 제어에 있어서 토오크 맥동은 전동기 제어성능 결정에 큰 요인으로 작용한다. 본 논문에서는 이러한 토오크 맥동을 효과적으로 저감하기 위한 새로운 토오크 추정 및 제어기법에 대해서 다룬다. 제안된 기법에서는 모델 기준 적응시스템(Model reference adaptive system ; MRAS) 기법을 이용하여 순시 토오크를 추정하고 적본형 가변구 조제어(Integral variable structure control ; IVSC)를 이용하여 추정된 토오크를 제어한다. DSP를이용하여 고 토오크 영구자석 동기전동기 제어시스템을 구성하고 실험을 수행하였으며 그 결과 제안된 제어기법이 우수한 토오크 맥동 저감효과를 가짐을 입증하였다.

• 전자공학회논문지B
• /
• 제32B권11호
• /
• pp.1445-1454
• /
• 1995

In this study, we have developed a prototype of the automatic defects detection system for capsule inspection using the computer vision techniques. The subjects for inspection are empty hard capsules of various sizes which are made of gelatine. To inspect both sides of a capsule, 2-stage recognition is performed. Features we have used are various lengths of a capsule, area, linearity, symmetricity, head curvature and so on. Decision making is performed based on average value which is computed from 20 good capsules in training and permission bounds in factories. Most of time-consuming process for feature extraction is computed by hardware to meet the inspection speed of more than 20 capsules/sec. The main logic for control and arithmetic computation is implemented using EPLD for the sake of easy change of design and reduction in time for developement. As a result of experiment, defects on size or contour of binary images are detected over 95%. Because of dead zone in imaging system, detection ratio of defects on surface, such as bad joint, chip, speck, etc, is lower than the former case. In this case, detection ratio is 50-85%. Defects such as collet pinch and mashed cap/body seldom appear in binary image, and detection ratio is very low. So we have to process the gray-level image directly in partial region.

• 한국군사과학기술학회지
• /
• 제18권4호
• /
• pp.432-440
• /
• 2015

UGVs(Unmanned Ground Vehicles) are robots that can substitute humans in reconnaissance operations of potentially dangerous and contaminated sites. Currently, there have been active research on utilizing UGVs in military environments. Much resrach has been focused on exploiting the weakness of topology-based routing and instead utilize location-based routing for the networking of UGVs. It is generally assumed that location-based routing methods can fully utilize the location information gained from GPS. However, this may not be possible in tactical environments due to enemy GPS jamming and LOS(Line of Sight) limitations. To solve this problem, we propose a location-based routing scheme utilizing low control message that can calibrate the location information using GPS information as well as location of neighboring UGV, movement direct and speed information. Also utilizing topology-based routing scheme to solve incorrect location information in GPS jamming region.

• 조명전기설비학회논문지
• /
• 제12권4호
• /
• pp.81-89
• /
• 1998

본 논문에서는 유도전동기의 가변속 구동시 제어성능이 우수한 직접빽터 제어시스템에 관하여 연구하였다. 벡터제어시 펼요한 전동기의 자속정보는 궤환제어의 장점이 있는 자속연산형을 사용하여 구하였으며, 이때의 모델은 회전자 회로의 전류모델 방식을 이용하였다. 또한 회전자 좌표계에서의 자속관측기를 구성하여 고정 자 좌표계 사용시 나타날 수 있는 d-q축 간섭현상 및 이산화의 오차를 경감시켰다. 디지털 시율레이션올 통하여 원활한 제어특성이 나타남을 입증하였으며 고성능 DSP소자 및 고속 IGBT를 채용한 인버터 드라이브 시스템을 구현하여 그 특성을 확인하였다.

• 동력기계공학회지
• /
• 제18권6호
• /
• pp.21-28
• /
• 2014

The studies of the spray characteristics for a CRDI engine had been advancing by many researchers, because the performance and exhaust emission were significantly affected with the spray characteristics. But most experiments of the studies would be done at low ambient pressure conditions under 2MPa. In this study, injection rates were measured with Zeuch's method at various ambient pressures to 5MPa and a constant injection pressure of 130MPa. On the same conditions, non-evaporating spray images were taken with a high speed camera and analyzed carefully with Adobe Photoshop CS3. Macroscopic spray characteristics and breakup processes in the spray could be found from the examined and analyzed data. The initial injection rate, penetration, angle, velocity and breakup of the spray were practically affected with a variation of the ambient pressure, but the injection start time and injection period were scarcely affected. As the ambient pressure was higher, the breakup of a high density droplet region in the spray was happened slowly and the main position of breakup was shifted from a front of the spray to a upstream around a nozzle. The results and techniques of spray visualization and injection rate measurement in this study would be practically effective to study a high pressure diesel spray for a CRDI.

• 대한기계학회논문집
• /
• 제19권11호
• /
• pp.3003-3013
• /
• 1995

The characteristics of the flow field in the tangentially fired furnace are presented. Experiments are conducted in the simplified cold type isothermal flow model. In the measurement of flow field, a hot wire anemometer is used. The hot wire was calibrated by lookup table method. The mean velocity field and turbulence characteristics are showed with changing the nozzle angle. In the center of the model, the low speed, unstable flow region is formed. The size and position of these regions are varied with changing the nozzle angle. It can be used as fundamental data in the design of the large furnace. From the experimental results, various turbulent characteristics of swirling flow field is obtained. And the entrainment mechanism of the jet flow field is described from the distribution of the skewness and the flatness. It can be used the raw data of approximate calculation and turbulent modelling.