• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.3
• /
• pp.277-283
• /
• 2009

In this paper, aluminum doped zinc oxide (ZnO:Al) thin films on plastic substrate such as poly carbonate (PC), polyethylene terephthalate (PET) were prepared by RF magnetron sputtering method for flexible solar cell applications. Effects of the sputter pressure on the structural, electrical and optical properties were investigated. The crystallinity and the degree of the (002) orientation were deteriorated with increasing the sputter pressure. When the sputter pressure was higher, the conductivity of ZnO:Al films was improved because of the high carrier concentration and the Hall mobility. High quality ZnO:Al films with resistivity as low as $1.9{\times}10^{-3}{\Omega}-cm$ and the optical transmittance over 80 % in the visible region have been obtained on PC substrate at 2 mTorr.

• Journal of the Korean Ceramic Society
• /
• v.32 no.8
• /
• pp.950-956
• /
• 1995

Y2O3 thin films were deposited by reactive sputtering of Y target in Ar and O2 gas mixture. Residual stress was measrued by sin2$\psi$ method of x-ray diffraction (XRD) and growth orientation was examined by measuring the relative intensity of (400) plane and (222) plane of Y2O3 films. In the case that Y2O3 films were deposited at 40$0^{\circ}C$ and at low working pressure below 0.05 torr the film had large compressive stress and (111) plane orientation. At working pressure of about 0.10 torr the film had small compressive stress and (100) orientation. Above working pressure of 0.20 torr, the films had nearly zero stress and random orientation. In the case that the (111) oriented film deposited at low working pressure below 0.05 torr, as substrate temperature decreased, (111) orientation increased. In the case the film, with (100) orientation, deposited at working pressure of about 0.10 torr, (100) orientation increased with decresing substrate temperature. These relationship of residual stress and growth orientation can be explained by the relationship of surface energy and strain energy.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.12
• /
• pp.966-972
• /
• 2010

Single-phase $Sr_2FeMoO_6$ thin films were produced by RF magnetron sputtering for use as electrodes in integrated sensors and found to be good conductors at room temperature. The films were deposited from a powder-type sputtering target under various conditions, and were crystallized by annealing. Elimination of $O_2$ gas during deposition, by the use of a solely Ar sputtering gas under a working pressure as low as possible, and vacuum annealing were important to promote the $Sr_2FeMoO_6$ phase. However, oxygen exclusion from sputtering and annealing was not enough to yield single-phase $Sr_2FeMoO_6$: hydrogen annealing was also required. Film production was optimized by varying the deposition parameters and hydrogen annealing conditions. The film had good electrical conduction, with a low resistivity of $1.6{\times}10^{-2}\Omega{\cdot}cm$ at room temperature.

• Korean Journal of Materials Research
• /
• v.21 no.12
• /
• pp.703-707
• /
• 2011

The electrochromic properties of tungsten oxide films grown by RF sputtering were investigated. Among the sputter parameters, first the $Ar:O_2$ ratios were controlled with division into only an $O_2$ environment, 1:1 and 4:1. The structure of each film prepared by these conditions was studied by X-ray diffraction, X-ray photoelectron spectroscopy and Rutherford backscattering spectroscopy. The sputter-deposited tungsten oxide films had an amorphous structure regardless of the $Ar:O_2$ ratios. The chemical compositions, however, were different from each other. The stoichiometric structure and low-density film was obtained at higher $O_2$ contents. Electrochemical tests were performed by cyclic voltammetry and chronoamperometry at 0.05 M $H_2SO_4$ solutions. The current density and charge ratio was estimated during the continuous potential and pulse potential cycling at -0.5 V and 1.8 V, respectively. The film grown in a higher oxygen environment had a higher current density and a reversible charge reaction during intercalation and deintercalation. The in-situ transmittance tests were performed by He-Ne laser (633 nm). At higher oxygen contents, a big transmittance difference was observed but the response speed was too slow. This was likely caused by higher film resistivity. Furthermore, the effect of sputtering pressure was also investigated. The structure and surface morphology of each film was observed by X-ray diffraction and scanning electron microscopy. A rough surface was observed at higher sputtering pressure, and this affected the higher transmittance difference and coloration efficiency.

• Journal of Surface Science and Engineering
• /
• v.29 no.5
• /
• pp.424-429
• /
• 1996

Thin films of Ti-Ni alloy were formed by sputtering under various Ar gas pressures and r. f. powers to investigate the optimum sputtering conditions and to demonstrate their shape memory effect. The composition and structure of the films were examined by electron micro-probe analysis and scanning electron microscope. These films were annealed in order to crystallize them. The mechanical property of the annealed films was evaluated by a conventional bending test. The transformation tmeperatures were determined by differential scanning calorimetry. The shape memory behaviour was examined quantiatatively by changing in sample temperature under various constant loads. It was found that the Ar gas pressure had a critical effect on the mechanical property of the thin film,s although the r.f. power also affected it. The films formed at a high Ar gas pressure were too brittle to be bent successfully. However, the films formed at a low Ar gas pressur could be bent and their shape memory behavior was found to be comparable with that of bulk Ti-Ni alloys.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.173-176
• /
• 1997

The III-V nitride semiconductor InN thin films which have the direct bandgap in visible light wavelength region have been deposited on Si(100) substrates and AIN/Si(100) substrates by rf reactive sputtering. InN thin films have been investigated on the structural, and electrical properties according to the sputtering parameters such as total pressure, rf power, and substrate temperature. It is found that optimal conditions required for fabricating InN thin films with high crystal Quality, low carrier concentration, high Hall mobility are total pressure 5mTorr, rf power 60W, substrate temperature 6$0^{\circ}C$ . InN thin films deposited on the AIN(60min.)/Si(100) substrates arid AIN(120min.)/Si(100) substrates showed remarkably high crystal quality and electrical properties. It is known that AIN buffer layer is to decrease free energy at interface between InN film and Si substrate, and then promoting lateral growth of InN films.

• Journal of Surface Science and Engineering
• /
• v.38 no.2
• /
• pp.69-72
• /
• 2005

ITO-Al-ITO multi-layers were deposited at room temperature by RF magnetron sputtering on polyethylene terephthalate (PET). The films were deposited at various pressures of $8\times10^{-4},\;1\times10^{-3},\;4\times10^{-3},\;8\times10^{-3}\;and\;1\times10^{-2}$ Torr. A correlation between microstructure and electro-optical properties was studied. Films deposited? at low pressure have higher transmission, and lower reflectance and resistance than film deposited at high pressure. Sheet resistance, transmission, and reflectance were $141.6\Omega/\Box\;88\%\;and\;6.8\%$ resectively when the deposition pressure was $8\times10^{-4}$ torr, that was the optimum condition.

• The Korean Journal of Ceramics
• /
• v.6 no.2
• /
• pp.110-115
• /
• 2000

$SrBi_2Ta_2O_9$ thin films were deposited at room temperature on the usual (111) oriented Pt bottom electrodes using r.f. magnetron sputtering, and then post-annealed at 650-$800^{\circ}C$ for 30min in oxygen flow. Low temperature processing which shows the preferred oriented SBT thin films was obtained by controlling the sputtering pressure and/or Sr content in target. The orientation and grain growth behavior of SBT thin films were dependent on Sr contents in films. With increasing the excess Bi content up to 50% in SBT thin films, it was possible to lower the onset temperature of grain growth. The c-axis preferred oriented SBT thin films were well-grown under the condition of low post-annealing($650^{\circ}C$) by lowering post-annealing pressure. After $10^{11}$ switching cycles, no polarization degradation was observed in both preferred oriented SBT capacitors.

• Transactions on Electrical and Electronic Materials
• /
• v.17 no.6
• /
• pp.351-354
• /
• 2016

The mechanical properties of ITO films such as adhesion and internal stress are very important for the commercial application of solar cell devices. We report high quality pulsed DC magnetron sputtered ITO films deposited on silicon and glass substrates with low resistivity and high transmittance for various working pressures ranging from 0.96 to 3.0 mTorr. ITO films showed the lowest resistivity of $2.68{\times}10^{-4}{\Omega}{\cdot}cm$, high hall mobility of $46.89cm^2/V.s$, and high transmittance (>85%) for the ITO films deposited at a low working pressure of 0.99 mTorr. The ITO films deposited at a low working (0.96 mTorr) pressure had both amorphous and polycrystalline structures and were found to have compressive stress while the ITO films deposited at higher temperature than 0.99 mTorr was mixture of amorphous and polycrystalline and was found to have tensile stress.

• Journal of the Korean Vacuum Society
• /
• v.13 no.4
• /
• pp.150-156
• /
• 2004

Boron nitride thin films were deposited on Si(100) substrate by RF (Radio-frequency) UBM (Unbalanced Magnetron) sputtering system. The effect of working pressure and substrate bias voltage on microstructure and compressive stress of boron nitride thin films has been investigated. In high working pressure, the alignment of hBN laminates increased with substrate bias voltage, in low working pressure, however, it was high in low substrate bias voltage. Compressive stress evolution and surface morphology of deposited BN films are closely related with the alignment of hBN laminates. The cBN phase without high compressive stress could be nucleated on hBN thin film by controlling the alignment of hBN laminates.