• Journal of KIISE:Information Networking
• /
• v.30 no.2
• /
• pp.252-259
• /
• 2003

In the case of link congestion, most of the existing ad-hoc routing protocols like AODV and DSR do not try to discover a new route if there is no change in the network topology. Hence, with low mobility, traffic may get concentrated on some specific nodes. Since mobile devices have low battery power and low computing capability, traffic concentration on a specific node is not a desirable phenomenon. Therefore, in this paper, we propose a new protocol called SLAP (Simple Load-balancing Ad-hoc routing Protocol) which resolves the traffic concentration problem by letting each node check its own load situation and give up its role as a packet forwarder gracefully in the case of high traffic load. We compare the performance of SLAP with that of AODV and DSR in terms of the forwarding traffic distribution.

• International Journal of Computer Science & Network Security
• /
• v.22 no.1
• /
• pp.255-261
• /
• 2022

Routing Protocol for Low-Power and Lossy Networks (RPLs) in Internet of Things (IoT) is currently one of the most popular wireless technologies for sensor communication. RPLs are typically designed for specialized applications, such as monitoring or tracking, in either indoor or outdoor conditions, where battery capacity is a major concern. Several routing techniques have been proposed in recent years to address this issue. Nevertheless, the expansion of the network lifetime in consideration of the sensors' capacities remains an outstanding question. In this research, aANN-CUCKOO based optimization technique is applied to obtain a more efficient and dependable energy efficient solution in IOT-RPL. The proposed method uses time constraints to minimise the distance between source and sink with the objective of a low-cost path. By considering the mobility of the nodes, the technique outperformed with an efficiency of 98% compared with other methods. MATLAB software is used to simulate the proposed model.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.5B
• /
• pp.557-565
• /
• 2011

In this paper, we assume that sensor nodes organize the multi-hop networks, are fixed, and operate as full function devices(FFD). The wireless sensor network(WSN) only consists of mobile nodes without the assistance from the fixed infrastructure, which increases the flexibility of the network. However, it is difficult to perform routing in the WSN, since sensor nodes freely join in and drop out of the network, and some sensor nodes have very low power. We propose the algorithm combining routing schemes based on the bitmap and cluster methods in this paper. Through computer simulations, we show the validity of the proposed algorithm.

• Journal of Korea Spatial Information System Society
• /
• v.12 no.1
• /
• pp.1-9
• /
• 2010

Recently, wireless sensor networks(WSNs) technology has been considered as one of the most critical issues in the ubiquitous computing age. The sensor nodes have limited battery power, so they should consume low energy through their operation for the long-lasting lifetime. Therefore, it is essential to use energy efficient routing protocol. For this, we propose a location-based energy-efficient routing protocol which constructs the energy efficient route by considering the quantity of Energy consumed. In addition, we propose a route reconstruction algorithm to handle the disconnection of message transmission. Finally, we show from performance analysis using TOSSIM that our protocol outperforms the existing location based routing protocols in terms of energy efficiency.

• KIISE Transactions on Computing Practices
• /
• v.23 no.2
• /
• pp.116-121
• /
• 2017

In wireless sensor networks, the multipath prefers energy efficient routing method due to the characteristic of low-power sensor which uses geographic method to transmit data packet through information of the neighbor nodes. However, when multipath meets the routing fail area called hole area, path overlap problem can occur, resulting in failed maintenance of disjoint multipath. To solve this problem, multipath research studies have been performed to exploit the modeling and detouring method in routing fail area by keeping the disjoint multipath. However, in an energy point of view, additional method like modeling can lead to a lot of energy consumption of sensor node. Moreover, lots of energy consumption of sensor node can shorten the life span of sensor network. In this study, we proposed an energy efficient geographic routing by keeping the disjoint multipath in routing fail area. The proposed scheme exploited the face routing using the geographic recovery method without additional method like modeling.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.10 no.3
• /
• pp.101-109
• /
• 2011

In this paper, we present a new routing protocol, multipath and multi-priority based routing protocol, (MMRP) for wireless multimedia sensor networks. The proposed MMRP chooses the multiple routing paths from source to the sink, then the selected paths are assigned with different priority levels depending upon the residual energy and transmission delay in the routing paths. That is, the highly prioritized I frames of the MPEG video are transmitted over the high priority routing paths, and other P and B frames are transmitted over the lower priority routing paths. The proposed MMRP protocol can be applied to time critical applications which require both lower latency and low power consumption over wireless multimedia sensor network. Simulations results of MMRP protocol show respectively an improvement of 23.48% and 23.11% in energy conservation and 81.6% and 32.01% improvement in latency as compared to protocols without and with multipath routing.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.11
• /
• pp.1879-1884
• /
• 2007

In the electric power industry, it is important that the supply of energy must be guaranteed. Many power utilities control and supervise the transmission line to avoid power failures. In case of underground tunnel, some troubles are reported in cable joint. To stabilize the power, it is needed to monitor the cable joint. Many researches of cable joint monitoring have been going on by partial discharge measurement and temperature measurement using optical cable. These methods need much cost to install and maintain, so it is only used in critical transmission line. In this research, we use wireless sensor technology, because of its low cost and easy installation. We develop the temperature monitoring system for cable joint. Temperature sensor is installed on the surface of cable joint and sends data to server through router node using wireless network. Generally Ad hoc routing is searched in wireless network. However, in this research, we design the static linear routing mechanism, which is suitable for electric power line monitoring and analyze the life time of the sensor node by measuring the amount of the battery consumption.

• Proceedings of the Korea Society of Information Technology Applications Conference
• /
• 2005.11a
• /
• pp.81-84
• /
• 2005

Various design schemes for network using wireless sensor nodes have been widely studied on the several application areas ranging from the real world information collection to environmental monitor. Currently, the schemes are focused on the design of sensor network for low power consumption, power-aware routing protocol, micro miniature operating system and sensor network middleware. The indoor localization system that identifies the location of the distributed nodes in a wireless sensor network requires features dealing with mobility, plurality and other environmental constraints of a sensor node. In this paper, we present an efficient location system to cope with mobility of multiple mobile nodes by designing a location handler that processes location information selectively depending on the nodes' density in a specific region. In order to resolve plurality of multiple mobile nodes, a routing method for the location system is also proposed to avoid the occurrence of overlapped location data.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2002.05a
• /
• pp.117-120
• /
• 2002

Bluetooth uses baseband of 2.4G ISM and composes radio Ad Hoc network based on Ad Hoc wireless connectivity which it used low power and low complexity solution. Bluetooth designed as can play detect, connect, discover service by surrounding other device even if users do not get acquainted all to Bluetooth. This paper operate wish to recognize mobility to routing algorithm how communication method and radio network in Bluetooth.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2007.10a
• /
• pp.465-468
• /
• 2007

An intelligent home network system using low-power and low-cost sensor nodes was designed and implemented. In Intelligent Home Network System, active home appliances control is composed of RSSI (Received Signal Strength Indicator) based user indoor location tracking, dynamic multi-hop routing, and learning integration remote-control. Through the remote-control learning, home appliances can be controlled in wireless network environment. User location information for intelligent service is calculated using RSSI based Triangle measurement method, and then the received location information is passed to Smoothing Algorithm to reduce error rate. In order to service Intelligent Home Network, moreover, the sensor node is designed to be held by user. The gathered user data is transmitted through dynamic multi-hop routing to server, and real-time user location & environment information are displayed on monitoring program.