• Journal of Institute of Control, Robotics and Systems
• /
• v.21 no.2
• /
• pp.168-172
• /
• 2015

In general, open-loop fiber-optic gyroscopes (FOG) are less stable than closed-loop FOGs but they offer simpler implementation. The typical operation time of line-of-sight (LOS) stabilization systems is a few seconds to one hour. In this paper, a open-loop fiber optic gyroscope (FOG) for LOS applications is designed and implemented. The design goal is aimed at implementing a low cost, compact FOG with low Angle Random Walk (ARW) (< $0.03deg/\sqrt{h}$) and bias instability (< 0.25deg/h). The FOG uses an open-loop all-fiber configuration with 100M PM fiber wound on a small diameter spool. In order to get the design goal, digital signal processing techniques for signal detection, modulation control and compensation are designed and implemented in FPGA.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.38A no.10
• /
• pp.885-892
• /
• 2013

The main advantage of ESPAR antenna is that ESPAR antenna requires only a single RF chain for reduction of transceiver's hardware complexity, as compared to conventional MIMO system. In conventional MIMO system, each data symbol is mapped to each antenna. But, each data symbol is mapped to each orthogonal basis pattern in ESPAR antenna system. In this paper, we design beamspace MIMO system using ESPAR antenna with single RF chain for MIMO system of low-complexity and low power consumption. And then, we analyze performance of beamspace MIMO according to each PSK modulation. Performance of beamspace MIMO system is similar to performance of conventional MIMO system. As a result of analyzing the performance of beamspace MIMO system using higher-order PSK modulation. we can confirm that performance characteristic of beamspace MIMO system with low complexity and low power consumption is similar to digital communication of signal domain.

• Proceedings of the KIEE Conference
• /
• 2005.10c
• /
• pp.326-328
• /
• 2005

In order to reduce the capital and overall operating cost of a fuel-cell system, a high-efficiency fuel-cell power inverter with a simple framework is required. The high-order two-inductance two-capacitance (LLCC) resonant technique is adopted in this study to implement a low-frequency 60-Hz sine wave voltage inverter utilized in the proton exchange membrane fuel-cell (PEMFC) system. The methodology for inverting dc voltage into low-frequency ac boltage is usually generated by the pulse-width-modulation (PWM) technique. However, the PWM-type inverter output has high-frequency harmonic components. Although an adequately designed filter could be utilized to overcome this problem, there are still some undesirable effects introduced by the high-frequency switching loss, electromagnetic-interference, harmonic current, and load variation. A novel power inverter via the LLCC resonant technique is designed for inverting dc voltage into 60-Hz ac sine wave voltage in the PEMFC system. This circuit scheme has the merits of low harmonic components, soft switching, high efficiency, and simplified implementation. The effectiveness of the proposed resonant inverter used for the PEMFC system is verified by numerical simulations and experimental results.

• Proceedings of the KIPE Conference
• /
• 2003.11a
• /
• pp.263-266
• /
• 2003

The high power factor converters are classified step-up, step-up-down and step-down converter, The power conversion system must be increased switching frequency in order to achieve a small size, a light weight and a low noise. And the power system brings on a high efficiency and high power factor. When a switch of the step down converter is operated with a commercial frequency(60Hz), a reactor using the converter is gone with a great number of harmonics waveforms of low grade. As results of this, the converter is decreased input power factor and is increased system size. To improved these, this paper proposes a PSM(Pulse Size Modulation) control strategy operated with high power factor.

• Proceedings of the KIPE Conference
• /
• 2001.07a
• /
• pp.372-376
• /
• 2001

Due to several advantages of Pulse Width Modulation(PWM) Converter, such as unity power factor operation, elimination of low-order harmonics and regeneration of motor braking energy to source, the application range of PWM Converter has been rapidly extended in industrial application. Nowadays, vector control algorithm and space vector PWM(SVPWM) method are applied to improve the performances of PWM Converter, but vector control algorithm and SVPWM require to use Microprocessor and other digital devices in hardware, causing costly and somewhat large dimension system. In every practical application of energy conversion equipments, the design and implementation should be carried out considering cost and performance. High performance and low cost is the best choice for energy conversion equipments. So, this paper presents the practical design method and implementation results of 3-phase PWM Converter with analog hysteresis current controller, and verifies the performances of unit power factor operation and energy regeneration operation via experimental results.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.24 no.7
• /
• pp.569-574
• /
• 2014

In order to investigate low frequency swishing noise of wind turbines, acoustic source model using a singularity in circular motion is introduced to derive analytic solution of Lowson acoustic analogy in time domain. Results in time and frequency domains computed by the solution show apparent modulation of amplitude and frequency. The solution indicates that time histories of acoustic pressure at receiver points varied significantly according to receiver's directional location, even when the retarded time distributions are similar. However, the corresponding time-averaged spectra of sound pressure at the receiver locations where the retarded time distributions are almost same are not significantly different. It can be inferred from these results that the time-averaged sound pressure spectra which cannot take into account the detailed difference in the time-variation of wind turbine noise may not represent the sound quality of wind turbines due to its swishing. Finally, as an introduction of procedure to quantify low frequency swishing noise level, relative variation of overall sound pressure level is obtained using tonal low frequency noise model.

• ETRI Journal
• /
• v.38 no.1
• /
• pp.90-99
• /
• 2016

In this work, we investigate differentially encoded blind transceiver design in low signal-to-noise ratio (SNR) regimes for orthogonal frequency-division multiplexing (OFDM) signaling. Owing to the fact that acquisition of channel state information is not viable for short coherence times or in low SNR regimes, we propose a time-spread frequency-encoded method under OFDM modulation. The repetition (spreading) of differentially encoded symbols allows us to achieve a target energy per bit to noise ratio and higher diversity. Based on the channel order, we optimize subcarrier assignment for spreading (along time) to achieve frequency diversity of an OFDM modulated signal. We present the performance of our proposed transceiver design and investigate the impact of Doppler frequency on the performance of the proposed differentially encoded transceiver design. To further improve reliability of the decoded data, we employ capacity-achieving low-density parity-check forward error correction encoding to the information bits.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.27 no.9
• /
• pp.1427-1435
• /
• 1990

This paper proposes the Selected Harmonic Elimination Pluse Width Modulation (SHE PW) scheme toreduce the ahrmonic components of source line current. To eliminate the low order harmonics which affects the source dominatly, we apply the Fourier series analysis to line current waveforms and then find out the switching patterns using the SHE PWM scheme. In addition to the analysis of harmonic effects, the three phase filter circuit is used to reduce high order harmonics. For the experimental realization, the converter circuit with power Transistor(PTR) is designed and the Pulse Time Control(PTC) is applied. The line current and the load voltage are measured under the condition of three phase application, highly inductive load.

• Proceedings of the KSR Conference
• /
• 1999.05a
• /
• pp.328-335
• /
• 1999

Three phase full bridge rectifier has been used to obtain dc voltage from three phase ac voltage source. The rectifier system has drawbacks that power factor is low and power flow is unidirectional. Therefore, when dc voltage increases due to regeneration of power the dynamic resister for dissipation of regeneration power must be installed. But three phase PWM converter can be controlled to operate with unity power factor and bidirectional power flow. Therefore when the PWM converter is used as do supply system, the dissipating resistor is not necessary. On this thesis, in order to design a controller having good performance, the hee phase PWM converter is completely modeled by using circuit DQ-transformation and thus a general and simple instructive equivalent circuit is obtained; the inductor set becomes a second order gyrator-coupled system and three phase inverter becomes a transformer as well. Under given phase angle(${\alpha}$) and modulation index(MI) of the three phase inverter, the dc and ac characteristics are obtained by analysis of the transformed equivalent circuit The validity of the equivalent circuit is confirmed through PSPICE simulation. And based on the dc and ac characteristics a controller with unity power factor is proposed.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.4C
• /
• pp.371-376
• /
• 2010

In this paper, we propose a new fast carrier recovery algorithm for high-order QAM systems. The proposed algorithm detects carrier frequency offset from the phase differences among the received symbols directly and combines it with the conventional carrier recovery, so that it is possible to achieve the carrier recovery with wide tracking range and fast acquisition time. Simulation results show that the proposed carrier recovery method reduces acquisition time at large frequency offset and low signal-to-noise ratio (SNR).