• Journal of the Korea Concrete Institute
• /
• v.17 no.5 s.89
• /
• pp.853-856
• /
• 2005

A low water/cement ratio leads to autogenous shrinkage of cement paste at an early age. This autogenous shrinkage is related to the change of relative humidity in the pore structure that is formed during the hydration process. The relationship between autogenous shrinkage and relative humidity change are relatively well defined today, but the effects of temperature on autogenous shrinkage, relative humidity, and pore structures have been studied less systematically. This study focused on correlating alterations of these properties of cement paste hydrated at constant temperatures of 20, 40, and $60^{\circ}C$. The test results clearly indicate that increasing curing temperature resulted in increased porosity, particularly for pores between 5 to 50 nm as measured by MIP, and increased autogenous shrinkages, as a consequence of a reduction of relative humidity at early ages.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1993.05a
• /
• pp.142-145
• /
• 1993

$TiO_2-V_2O_5$ thin films are fabricated by Sol-Gel method and humidity sensing properties have been investigated. As the results of humidity sensing properties of thin films fabricated as humidity sensor, it is confirmed to have good humidity sensing properties in high humidity and low frequency regions.

• Korean Journal of Veterinary Research
• /
• v.36 no.1
• /
• pp.131-142
• /
• 1996

The effect of relative humidity in swine house on swin pleuropneumonia was examined in piglets experimentally infected with Actinobacillus pleuropneumoniae serotype 5. A total of 20 piglet were grown under 30~40%, 41~50%, 51~64% and 65~80% relative humidity chambers after intratracheal inoculation of A pleuropneumoniae. Characteristic fibrinous pleuropneumonia was observed in the pigs grown at the low relative humidity groups. The detailed results were as follows : 1. Growth performance and environment conditions were lower than high relative humidity groups. 2. Characteristic histopathological findings were fibrinous pleuritis and pneumonia accompanied congestion, hemorrhage, thrombosis and edematous change. 3. Antigenic distribution of inoculated bacterium was found mainly in alveolar macrophages or accumulated foci of macrophages adjacent to necrotic area. 4. Characteristic electron microscopic findings were proliferation of type II pneumocyte with increased lamella bodies and activated alveolar macrophages with pseudopods and widening of interstitium.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.7 no.1
• /
• pp.16-20
• /
• 2001

In order to optimize designing process of corrugated fiberboard boxes for agricultural products, first of all, compression strength of each liner were experimentally evaluated on the various conditions of relative humidity and analyzed by liner regression analysis. At the 66 percents of relative humidity, IK(imported kraft liner) liner board lost little of its compression strength compared to others. At the relative humidity 93 percents, KA liner board lost its compression strength only 40 percents while SK liner board lost up to 56 percents. From the result of prediction modeling of ring crush strength in various humidity conditions, R square values were ranged from 0.59 to 0.97. At 56 percents of RH or below, R square values were relatively low, but at 66 percents of RH or higher, the values were 0.85 or higher. The significance values were lower than 0.001 at every RH condition. Level of significance of experimented values was about 80 percents of predicted values and R square values were between 0.89 to 0.95.

• Journal of Biosystems Engineering
• /
• v.29 no.6 s.107
• /
• pp.495-500
• /
• 2004

This study was performed to develop thin layer drying equations for low temperature. Thin layer drying tests of short grain rough rice were conducted at three low temperature levels of 15, 25, $35^{\circ}C$ and two relative humidity levels of 30, $50\%$, respectively. The measured moisture ratios were fitted to the selected four drying models (Page, Thompson, Simplified diffusion and Lewis model) using stepwise multiple regression analysis. The overall drying rate increased as the drying air temperature was increased and as relative humidity was decreased, but the effect of temperature increase was dominant. Half response time (Moisture ratio=0.5) of drying was affected by both drying temperature and relative humidity at drying temperature of below $25^{\circ}C$, but at $35^{\circ}C$ was mainly affected by drying temperature. The results of comparing coefficients of determination and root mean square error of moisture ratio for low drying models showed that Page model was found to fit adequately to all drying test data.

• Journal of the Korean Wood Science and Technology
• /
• v.42 no.1
• /
• pp.49-57
• /
• 2014

The pre-air-drying of Korean pine before the high-temperature and low-humidity drying was shown to be effective in uniform moisture content distribution and prevention of surface check. Our results suggest that initial moisture content of the timber also plays important role in high-temperature and low-humidity drying method. The pre-air-drying also helps in the reduction of surface checks in Korean pine when compared to the Korean pine dried by only high-temperature and low-humidity. End-coating was not effective in the prevention of twist, shrinkage, case hardening and internal checks. The pre-air-drying reduces the internal tension stresses which occur during high-temperature and low-humidity drying thus decreasing case hardening and also preventing internal checks. The pre-air-drying decreases the moisture content and causes shrinkage which leads to increased twist in the Korean pine.

• Journal of the Korean housing association
• /
• v.17 no.2
• /
• pp.125-134
• /
• 2006

The tightness of windows have devoted to the improvement of thermal insulation and energy saving in buildings. But it is known that this tightness causes some side effects such as low ventilation, low capacity to humidity and temperature control and these are not profitable for inhabitants. To act on these side effects, Korean traditional windows which are composed of Han-Ji(Koreand traditional paper) and Chang-Sal(Korean traditional wooden frame) have been studied to get a reasonable solutions for these problems. In this study, to compare the thermal and humidity control performance of current window(12 mm pair) and Korean traditional windows, frames which are made of existing window and Korean traditional windows are adapted to scale model house and then humidity and temperature of in and out of scale model house are measured and analysed. The results of this study are followings ; 1) When Korean traditional window charges 20cm(1/8 of total window area) from total window area, Han-Ji window has higher thermal insulation than that of existing window in daytime. There is the most big thermal difference when double faced with double-ply Han-Ji window is placed to mock-up house. In night-time, the temperature difference is very small so this means that Korean traditional window is good to cover direct sunlight in daytime and reduce the temperature of balcony. One faced with one-ply han-Ji window has the best humidity penetration performance among three type of Korean traditional windows. 2) When Korean window area enlarged to 40cm(1/4 of total window area), the function of 40cm width Han-Ji window is higher than that of 20cm's. This means that enlargement of Han-Ji window cover direct sunlight more and is more efficient in humidity penetration.

• Fashion & Textile Research Journal
• /
• v.2 no.3
• /
• pp.220-226
• /
• 2000

This study was to determine the characteristics of vapor-permeable waterproof finished fabric by the coating method. 4 different kinds of coating fabrics (A : wet, porous, polyurethane, B : dry, no porous, polyurethane, C : shape memory polyurethane and D : dry, porous polyurethane) were used, which were developed recently With this sample, moisture transport rate ($40^{\circ}C$, 45%RH & $40^{\circ}C$, 95%RH), changes of coating side's shape by washing times, water repellency rate, contracted length, qmax, heat conductivity, heat keeping rate, heat keeping rate with cotton, heat keeping rate on humidity temperature and humidity within clothing etc. were checked. And it was done in a climate chamber under $20{\pm}2^{\circ}C$, $65{\pm}5%RH$. The results of this study were as follow; In the moisture vapor transmission of sample B and C increased on high temperature and high humidity while sample A and D decreased, on this condition. Qmax rate had high relation with ground fabric's surface properties and the order was A>C>D>B. Heat conductivity had high relation with thickness and surface properties. Heat keeping rates on sweat condition showed around half percents of heat keeping rates on normal condition, but had no relation with moisture vapor transport rate. Changes of the fabric's properties by washing times were different in accordance with the construction of fabrics and the coating resin. Sample C had tow heat keeping rate on the high temperature and humidity and high heat keeping rate on the low temperature and humidity Moisture transport rate of vapor-permeable waterproof finished fabrics had high relation with the properties of ground fabrics on low humidity condition, but on the high humidity condition, it was highly related with the properties of coating resin.

• KSTLE International Journal
• /
• v.6 no.2
• /
• pp.39-44
• /
• 2005

Friction and wear properties of the Boron carbide ($B_{4}C$) coating 100 nm thickness were studied under various relative humidity (RH). The boron carbide film was deposited on silicon substrate by DC magnetron sputtering method using $B_{4}C$ target with a mixture of Ar and methane ($CH_4$) as precursor gas. Friction tests were performed using a reciprocation type friction tester at ambient environment. Steel balls of 3 mm in diameter were used as counter-specimen. The results indicated that relative humidity strongly affected the tribological properties of boron carbide coating. Friction coefficient decreased from 0.42 to 0.09 as the relative humidity increased from $5\%$ to $85\%$. Confocal microscopy was used to observe worn surfaces of the coating and wear scars on steel balls after the tests. It showed that both the coating surface and the ball were significantly worn-out even though boron carbide is much harder than the steel. Moreover, at low humidity ($5\%$) the boron carbide showed poor wear resistance which resulted in the complete removal of coating layer, whereas at the medium and high humidity conditions, it was not. X-ray photoelectron spectroscopy (XPS) and Auger electron spectroscopy (AES) analyses were performed to characterize the chemical composition of the worn surfaces. We suggest that tribochemical reactions occurred during sliding in moisture air to form boric acid on the worn surface of the coating. The boric acid and the tribochemcal layer that formed on steel ball resulted in low friction and wear of boron carbide coating.

• Korean Chemical Engineering Research
• /
• v.45 no.4
• /
• pp.345-350
• /
• 2007

During PEMFC operation, OCV(open circuit voltage) and low humidity conditions accelerate the degradation of perfluorosulfonic acid membrane. There have been no studies that clearly explain why these conditions accelerate the membrane degradation. In this study, the hydrogen permeability through the membrane, I-V polarization of MEA, fluoride emission rate(FER) and $H_2O_2$ concentration in condensed water were measured during cell operation under OCV and low relative humidity(RH). The experimental results were evaluated with oxygen radical mechanism the most commonly known for membrane degradation. It seems that low RH of anode is a good condition for $H{\cdot}$ radical formation on the Pt catalyst and the OCV condition accelerate the $H{\cdot}$ to form $HO_2{\cdot}$ radical attacking the polymer membrane.