• Spatial Information Research
• /
• 제18권3호
• /
• pp.13-22
• /
• 2010

최근 이상기후로 인한 강풍 및 태풍이 자주 발생하여 많은 인적, 물적 피해가 발생함에 따라 구조물 설계 시 적용하는 풍하중 산정에 관한 연구의 중요성이 강조되고 있다. 지형에 따른 풍속지형계수의 증가는 풍속의 증가를 의미하며 풍속의 증가는 제곱에 비례하여 풍하중에 영향을 미치기 때문에 풍속지형계수 산정을 위한 지리정보를 정확하게 측정하는 것이 필요하다. 따라서, 본 연구에서는 BIM(Building Information Modeling) 프로그램인 ArchiCAD를 이용하여 정확하고 합리적인 풍속지형계수 산정 방법을 제시하고자 한다. 풍하중을 고려한 구조물 설계 시 본 연구에서 제안한 방법을 이용함으로서 설계의 합리성과 경제성을 더 높일 수 있을 것이다.

• Transactions on Electrical and Electronic Materials
• /
• 제14권5호
• /
• pp.225-230
• /
• 2013

This paper presents a novel shunt radio frequency microelectromechanical system switch on a quartz substrate with stiff ribs around the membrane. The buckling effects in the switch membrane and stiction problem are the primary concerns with RF MEMS switches. These effects can be reduced by the proposed design approach due to the stiffness of the ribs around the membrane. A lower mass of the beam and a reduction in the squeeze film damping is achieved due to the slots and holes in the membrane, which further aid in attaining high switching speeds. The proposed switch is optimized to operate in the k-band, which results in a high isolation of -40 dB and low insertion loss of -0.047 dB at 21 GHz, with a low actuation voltage of only 14.6 V needed for the operation the switch. The membrane does not bend with this membrane design approach. Finite element modeling is used to analyze the stress and pull-in voltage.

• Journal of Advanced Marine Engineering and Technology
• /
• 제39권2호
• /
• pp.152-158
• /
• 2015

Unlike photovoltaic systems installed on land, photovoltaic systems applied to the offshore plant have the characteristic that is installed in a limited space. For single point mooring plant, it is advantageous in terms of a reliable power supply to be installed in different directions of photovoltaic panels, because it is not possible to identify the position of the sun by rotation of the plant itself. Differences of installation angle between photovoltaic panels make a difference of the intensity of radiation irradiated on each photovoltaic panel, and it brings loss of generation quantity due to the partial shading. In order to provide a photovoltaic system suitable for offshore plant, the modeling which contains multiple photovoltaic panels controlled by single controller is performed. Then, it was examined how the output characteristics of the photovoltaic system change about the difference of the intensity of radiation that varies depending on the altitude of the sun. Finally, through the simulation, a development model of the photovoltaic system which is suitable for offshore plant is suggested.

• 오토저널
• /
• 제13권4호
• /
• pp.62-75
• /
• 1991

The purpose of this study is to perform modelings and experiments to measure air flow rate using hot-wires and a CTA(Constant Temperature Anemometer). The flow rate can be obtained by measuring the heat loss of the hot-wire due to the variations of flow velocity when the hot-wire is maintained at uniform temperature. But the defect of this method is that the output signal changes not only by the flow rate but also by the ambient temperature. Thus, in the present study, a method which compensates the variations of the ambient temperature has been introduced to measure exact flow rate. To be more specific, the bridge circuit of the usual hot-wire anemometer system has been modified in such a way that a temperature resistance sensor and a variable resistance are placed in one of the legs to compensate the different temperature coefficients of both the hot-wire and the temperature compensating resistance for flow velocity or for flow mass up to the flow temperature of 50 .deg.C. Comparing the modeling and experimental results, it has been shown that the compensating point differs as the flow rate varies. Therefore, optimum compensation points are sought to construct the circuit. The present modeling and experimental results may be applied to the design of actual air flow meters for automobiles.

• 한국콘텐츠학회논문지
• /
• 제7권4호
• /
• pp.133-140
• /
• 2007

기존의 상업적인 3D CG 애니메이션 제작 공정 구조는 부서간의 병목현상으로 모든 부서가 동시에 작업을 할 수 있는 효율적인 구조로 이루어지지 않고 있다. 예를 들어, 애니메이팅 작업을 하기 위해선 선행되어야 할 모델링과 Set-Up 단계가 끝나기 전에는 애니메이팅 작업을 할 수가 없다. 그 결과, 제작 일정의 지연, 제작비의 손실을 발생시키게 되고, 또한 선행된 작업에 수정을 가할 경우 수정이 끝날 때 까지 애니메이팅 작업은 중단된다는 결과를 야기 시킨다. 이런 문제는 표준으로 정해 놓은 "마스터 캐릭터"의 적용으로 도움을 줄 수가 있는데, 프로젝트의 시작과 동시에 모델링과 set-up 그리고 다른 어떤 작업과도 독립적으로 애니메이팅 작업을 시작 할 수 있고 수정 작업도 독립적으로 수행이 가능해서 애니메이션 제작공정을 효율적으로 관리할 수 있다.

• 전기학회논문지
• /
• 제64권2호
• /
• pp.201-207
• /
• 2015

Turbine-generator torsional response is caused by interaction between electrical transient air-gap torque and mechanical characteristics of turbine-generator shafts. If torsional shaft torque exceeds a certain threshold, the loss of fatigue life may occur and, in the end, it is possible to happen permanent shaft failure. Therefore, it is required to understand the torsional response for reliable operation and protection of turbine-generator shaft system. In this paper, we introduced multi-mass modeling method of turbine-generator shaft system using mechanical-electrical analogy and state-space equation to verify the transient torsional response based on ElectroMagnetic Transient Program (EMTP). These simple realization methods for turbine-generator shaft torsional response could be helpful to understand torsional interaction phenomena and develop the transient torque reduction countermeasures for turbine-generator shaft system.

• Structural Engineering and Mechanics
• /
• 제57권6호
• /
• pp.1085-1105
• /
• 2016

The drainage problem in bifurcations causes pecuniary losses when hydropower stations are undergoing periodic overhaul. A new design philosophy for Y-typed bifurcations that are flat-bottomed is proposed. The bottoms of all pipe sections are located at the same level, making drainage due to gravity possible and shortening the draining time. All fundamental curves were determined, and contrastive analysis with a crescent-rib reinforced bifurcation in an actual project was conducted. Feasibility demonstrations were researched including structural characteristics based on finite element modeling and hydraulic characteristics based on computational fluid dynamics. The new bifurcation provided a well-balanced shape and reasonable stress state. It did not worsen the flow characteristics, and the head loss was considered acceptable. The proposed Y-typed bifurcation was shown to be suitable for pumped storage power stations.

• 설비공학논문집
• /
• 제25권3호
• /
• pp.119-125
• /
• 2013

IInsulation material is generally used for preventing heat loss from heat transport fluids, and water absorption severely reduces the insulation property. The purpose of this study is to evaluate the amount of water absorption supplied by the pouring method and spraying method, to investigate the effects of water absorption on the thermal conductivity of an insulation material, and modeling the relation between water absorption and thermal conductivity. E-glass, a kind of glass fiber, and HYPERLITE, mainly composed of pearlite, are selected, to compare hygroscopic and insulation properties. E-glass is found to have much higher water absorptivity, compared to HYPERLITE. The thermal conductivity of the water-absorbed E-glass is increased by more than 150%, compared to that of no absorption, while variation of the thermal conductivity of HYPERLITE with water absorption is insignificant. A three-stage model of water absorption for thermal conductivity is developed, and the modeling results are found to be in good agreement with the experimental data.

• 한국정보처리학회논문지
• /
• 제7권5호
• /
• pp.1361-1369
• /
• 2000

For the implementation of 3D Sound Localization system, the binaural filtering by HRTFs is generally employed. But the HRTF filter is of high order and its coefficients for all directions have to be stored, which imposes a rather large memory requirement. To cope with this, research works have centered on obtaining low dimensional HRTF representations without significant loss of information and synthesizing the original HRTF efficiently, by means of feature extraction methods for multivariate dat including PCA. In these researches, conventional linear PCA was applied to the frequency domain HRTF data and using relatively small number of principal components the original HRTFs could be synthesized in approximation. In this paper we applied neural network based nonlinear PCA model (NLPCA) and the nonlinear PLS repression model (NLPLS) for this low dimensional HRTF modeling and analyze the results in comparison with the PCA. The NLPCA that performs projection of data onto the nonlinear surfaces showed the capability of more efficient HRTF feature extraction than linear PCA and the NLPLS regression model that incorporates the direction information in feature extraction yielded more stable results in synthesizing general HRTFs not included in the model training.

• 에너지공학
• /
• 제21권3호
• /
• pp.211-220
• /
• 2012

본 연구에서는 창문을 통한 건물의 에너지손실을 알아보기 위해서 창호시스템의 구조체를 모델링하여 구조체 재질에 따른 열적 손실부분을 분석하였고, 건물에서 창문을 통한 난방부하변화량을 알아보기 위해서 시뮬레이션을 통하여 건물을 모델링하여 창문의 종류와 구조체의 재질에 따른 건물의 에너지 변화량과 온도 변화를 분석하였다.