• Proceedings of the Korea Concrete Institute Conference
• /
• 2000.04a
• /
• pp.417-422
• /
• 2000

In prestressed concrete structures, determining serviceability and safety it is important to exactly calculate effective prestress force acting on structures. for the determination of effective prestress force, friction loss of the prestressing tendon should be decided exactly, but it is very difficult to measure the exact prestress force on the site and there is no actual field data. Therefore the friction loss coefficient recommended by the specification is not verified. in this paper, the friction loss standard PSC-Beam will be investigated, and is will be found what kind of relationship between the specification and the site. The results from this study can be summarized as follows. For jacking at both ends, actual intial prestress force in the center section of PCS-Beam was about 1.61% larger than theoretical initial prestress force and for hacking at one end, actual initial prestress force was approximate 4.9% lower than theoretical initial prestress force. Thus, for the exact calculation of friction loss, friction coefficient should be modified according to jacking methods.

• The KSFM Journal of Fluid Machinery
• /
• v.2 no.1 s.2
• /
• pp.73-80
• /
• 1999

Leakage vortices formed new blade tip causes an increase of total pressure loss near the casing endwall region and as a result, the efficiency of rotor decreases. The reduction of rotor efficiency is related to the size of the tip clearance. In this study, the three-dimensional flowfields in an axial flow rotor were calculated by varying the tip clearance under various flow rates, and the numerical results were compared with experimental ones. The effects of tip clearance and attack angle on the leakage vortex and overall performance, and the loss distributions were investigated through numerical calculations. In this study, tip leakage flow rate and total pressure loss by tip clearance were evaluated using numerical results and approximate equations were presented to evaluate the reduction of rotor efficiency by tip leakage flow.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.797-801
• /
• 2003

The Statistical Energy Analysis is based on the power flow and the energy conservation between sub-systems, which enable the prediction of acoustic and structural vibration behavior in mid-high frequency ranges. This paper discusses the identification of SEA coupling loss factor parameters from experimental measurements of small reverberation chamber sound pressure levels and structural accelerations. As structural subsystems, steel plates with and without damping treatment are considered. Calculated CLFs were verified by both transmission loss values for air-borne CLF case and running SEA commercial software As a result, CLFs have shown a good agreement with those computed by software. Acoustical behavior of air-borne noise and structure-borne noise has been examined. which shows reasonable results, too.

• Proceedings of the KIEE Conference
• /
• 1995.07b
• /
• pp.528-530
• /
• 1995

In the conventional power flow calculations, the slack bus is assumed to undertake the total transmission loss for the convenience of numerical computation. This is an unrealistic assumption because, in real power system, the transmission loss is supplied by all the generators and makes the power flow calculation results somewhat distorted. This paper proposes a new loss redistribution algorithm that can reduce the distortion of power flow results. In the proposed method, the system power loss redistribution algorithm is added to the conventional power flow equations and jacobian elements that are related the real power are newly constructed. In each iteration step, the power output of each generator is updated to consider the effect of calculated total power losses. Finally the usefulness of proposed method are tested through the some appropriate case studies.

• Journal of Electrical Engineering and Technology
• /
• v.2 no.2
• /
• pp.194-200
• /
• 2007

The deregulation problem has recently attracted attentions in a competitive electric power market, where the cost must be earmarked fairly and precisely for the customers and the Independent Power Producers (IPPs) as well. Transmission loss is an one of several important factors that determines power transmission cost. Because the cost caused by transmission losses is about $3{\sim}5%$, it is important to allocate transmission losses into each bus in a power system. This paper presents the new algorithm to allocate transmission losses based on an integration method using the loss sensitivity. It provides the buswise incremental transmission losses through the calculation of load ratios considering the transaction strategy of an overall system. The performance of the proposed algorithm is evaluated by the case studies carried out on the WSCC 9-bus and IEEE 14-bus systems.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.9A
• /
• pp.983-990
• /
• 2004

In this paper, we calculated the input impedance of the power line communication(PLC) networks using medium voltage power line. First of all, we proposed input and output teoninal model of PLC network, and calculated the input impedance applying the attenuation constants by radiation loss, conductor loss, dielectric loss. From the calculation result, we knew that the attenuation by radiation loss was largest, and the input impedance appears like a standing wave fonn with a fixed cycle because the high reflection at the input terminal for the characteristic impedance of the power line is very large. And also the cycle of input impedance depends on the coaxial cable length, and the amplitude depends on the characteristic impedance of power line and losses. From the measurement result, calculated result was very similar to the measured result.

• Nuclear Engineering and Technology
• /
• v.17 no.4
• /
• pp.256-266
• /
• 1985

The loss of coolant flow accident is analyzed for the pressurized water reactor of Korea Nuclear Unit-1. The loss of coolant flow accident is classified into three types in accordance with its severity; partial loss of coolant flow, complete loss of coolant flow and pump locked rotor accident. Analysis has been carried out in three stages; system transient and average core analysis, DNBR calculation and hot spot analysis. The purpose of developing KTRAN is to simulate the transient fast. For the DNBR calculation, the thermal hydraulic codes, SCAN and COBRA IV-1, are adopted. And for the hot spot analysis, the fuel thermal transient code LTRAN is employed. This code system should be fast responding to the transient analysis. In case the transient occurs, severity comes within a couple of seconds. So response should be fast to accomodate the following sequence of the accident. Unfortunately this purpose could not be achieved by KTRAN. However, the calculated results are well comparable with FSAR results in range. Thereby, the effectiveness of KTRAN code analysis in this type of accident is proven.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.2
• /
• pp.136-148
• /
• 1997

The present study has been carried out to develop a computational procedure for the analysis of the off-design performance in centrifugal compressors with vaneless diffusers by integrating empirical loss models and analytical equations. Losses in centrifugal compressors stem from a number of sources and their exact calculation is not yet possible. This study investigates several modeling schemes and shows that a fairly good prediction can be achieved by a proper selection of the most important flow parameters resulting form a meanline one-dimensional analysis. The performance maps for compressors are calculated and compared with measured performance maps. The off-design performance characteristics in terms of the pressure ratio vs. mass flow produced have generally correct forms. However, no universal means have been found to predict accurately the onset of surge. The prediction method developed through this study can serve as a tool to ensure good matching between parts and it can assist the understanding of the operational characteristics of general purpose centrifugal compressors.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.6
• /
• pp.669-681
• /
• 2012

In this paper, analytical calculations using a novel mutual inductance formula for a resonant wireless power transmission system using helical coils. The look-up table of critical variables during the mutual inductance calculation process was formulated. The calculation results for resonant frequency and insertion loss were compared with experimental results when the distance between the two helical coils in a structure where the transmission and reception is symmetrical was varied with 10 mm increments from 53 mm to 500 mm. On average, the resonant frequency showed a difference of 5.63 % between the experimental results and the calculation results. The insertion loss had an average difference 2.25 dB where the smallest difference of 0.33 dB occurred with 290 mm. It was found that the experimental results without using a balun were in greater agreement with the calculation results.

• Journal of the military operations research society of Korea
• /
• v.15 no.2
• /
• pp.160-169
• /
• 1989

This study is concerned with the loss rate calculation for evaluating the safety of aircraft series. The objective of this study is to provide the estimation method of safety for the determination of aircraft series, when the aircraft is directly purchased off-the-shelf or co-produced. Especially, in case the initial operation capabilities of alternative aircrafts are substantially different, this research proposes the modified cumulative average method which can effectively estimate the safety of aircraft.