• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2000.04a
• /
• pp.51-56
• /
• 2000

Demand for new nondestructive evaluations is growing to detect tensile crack growth behavior to predict long term performance of materials and structure in aggressive environments, especially when they are in non-visible area. Acoustic emission technique is well suited to these problems and has drawn a keen interests because of its dynamic detection ability, extreme sensitivity and location of growing defects. In this study, we analysed acoustic emission signals obtained in tensile test of high strength fire resistance steel for frame structure with time frequency analysis methods. The results obtained are summaries as follows ; In the T and TN specimen consisting of ferrite and pearlite grains, most of acoustic emission events were produced near yield point, mainly due to the dislocation activities during the deformation. However, B specimen under $600^{\circ}C$ - 10min had a two peak which was attribute to the presence of martensite phase. The first peak is before yield point the second is after yield point. The sources of second acoustic emission peak were the debonding of martensite-martensite interface and the micro-cracking of brittle martensite phase. In $600^{\circ}C$-30min to $700^{\circ}C$-60min specimens, many signals were observed from area before yield point and counts were decreased after yield point.

• Journal of the Korean Society of Industry Convergence
• /
• v.25 no.6_3
• /
• pp.1165-1171
• /
• 2022

In this paper, the results of an experimental study were presented by measuring and comparing the flexural strength and deformation on the carbon fiber sheet strength reinforced concrete beam considering end anchorage effect. For this purpose, total six specimens of 100×100×600mm size were prepared and tested according to the KDS 14 20 20. The specimens were categorized in three cases as reference beams without strengthening, beams carbon fiber strengthened but not anchored and beams carbon fiber strengthened also anchored. Experimental results showed that the end anchorage contributed to increase the flexural strength about 42% greater than that of carbon fiber sheets alone, and the number and width of cracks were relatively increased. The results support a considerable effects of end anchorage for carbon fiber strengthened reinforced concrete beams in enhancing the flexural performance. Further studies are needed in durability and long term behavior of carbon fiber sheet strengthened reinforced concrete beams.

• Computers and Concrete
• /
• v.19 no.5
• /
• pp.579-588
• /
• 2017

Creep and shrinkage are the main types of volume change with time in concrete. These changes cause deflection, cracking and stresses that affect durability, serviceability, long-term reliability and structural integrity of civil engineering infrastructure. Although laboratory test may be undertaken to determine the deformation properties of concrete, these are time-consuming, often expensive and generally not a practical option. Therefore, relatively simple empirically design code models are relied to predict the creep strain. This paper reviews the accuracy of creep and shrinkage predictions of reinforced concrete (RC) shear walls structures strengthened with carbon fibre reinforced polymer (CFRP) plates, which is characterized by a widthwise varying fibre volume fraction. This review is yielded by three commonly used international "code type" models. The assessed are the: CEB-FIP MC 90 model, ACI 209 model and Bazant & Baweja (B3) model. The time-dependent behavior was investigated to analyze their seismic behavior. In the numerical formulation, the adherents and the adhesives are all modelled as shear wall elements, using the mixed finite element method. Several tests were used to demonstrate the accuracy and effectiveness of the proposed method. Numerical results from the present analysis are presented to illustrate the significance of the time-dependency of the lateral displacements and eigenfrequencies modes.

• The Journal of Engineering Geology
• /
• v.13 no.2
• /
• pp.227-238
• /
• 2003

Understanding of a creep behavior in rocks under a constant load, due to visco-elastic properties of rock, is an essential element to predict a long term ground deformation. In order to clarify the creep characteristics of the mudstone in Duho formation at Pohang basin, deposited during Tertiary, a series of laboratory tests including physical properties, unconfined compressive strength and uniaxial creep tests, was performed. The mudstone showed a higher creep potential due to 26% of clay minerals such as illite and chlorite. The unconfined compressive strength of the rock was $462{\;}kg/\textrm{cm}^2$ in average, and four creep tests were performed under constant stress of 40 to 70 % of the strength. The creep constants in the empirical and theoretical equations were deduced from the time-strain curves obtained from the tests. Among the several equations, the empirical equation proposed by Griggs and theoretical equation of Burger’s model are appreciated as the best one to express the creep behavior of the mudstone. Instantaneous elastic strain was linearly increased with stress level but strain velocity during the first creep is decreased with a similar pattern by time lapse regardless the stress level.

• Journal of the Korean GEO-environmental Society
• /
• v.14 no.9
• /
• pp.57-65
• /
• 2013

Carbonate sands can be crushed under low confining pressure to achieve high compressibility. So particle crushing has significant influence on characteristics of strength and deformation. Trial embankment and hydrotest are conducted on Sabkha layer, consisting of carbonate sand to build tank structure. In this paper the settlement behavior was analyzed from each test. Particle crushing happened from 80 to 170kPa stress under compression test, and calcium was detected from chemical test. The test result came out Sabkha soil was very weak and easy to be crushing. About trial embankment test, particle crushing was not happen, and then extinction of pore water pressure and settlements were finished just during 2 days. On the other hand, the long-term settlement was happened in hydrotest. So the two test results did not correspond to each other. If loading stress is higher than yielding stress, instant settlement and secondary compression settlement are happened as a result of the particle crushing.

• Journal of the Korean Geotechnical Society
• /
• v.22 no.2
• /
• pp.19-28
• /
• 2006

Long-term field observations were performed in three excavation sites in order to investigate the displacement behavior of adjacent ground during overall excavation procedure, where the depths of deep excavations were 15 m$\∼$29 m. In this study, ground settlements and lateral displacements of braced wall measured during installation of retaining wall and removal of bracing were specially focused to evaluate the behavior quantitatively according to three-stage-divided procedure, i.e. pre-excavation, main excavation, and removal of bracing. Through field measurements on three excavation sites, lateral displacements induced during removal of bracing are approximate to 40$\%$ of the amount found during main excavation stage and additional adjacent ground deformation during post-excavation procedure ranges from 18$\%$ to 33$\%$ of that found during main excavation stage, based on the settlement volume. In conclusion, it was quantitatively identified in this study that the deformations of adjacent ground during pre- and post-excavation stage were not negligible.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.11 no.3
• /
• pp.75-84
• /
• 1991

When we construct the earth structures such as embankments, on soft ground which are consisted of thick marine silty clay, the foundations deform due to consolidation and creep. For the stabilization of the earth structures constructed on soft foundations, we usually uses the mattress and they play an important role in increasing an ultimate bearing capacity by the dispersion of load of embankment. The purpose of this paper was to predict rationally a long term deformation of earth structures and to contribute to embankment design and maintenance. We determined a rheological model of marine clay from experimental data, and developed a computer program using the chosen model and found out the long term behavior of embankment. The results of this paper are as follows: 1. The developed program can analyze simultaneously consolidation and creep. 2. From the results of creep test, the rheological model of marine silty clay can be represented by the Vyalov model. 3. The displacement of embankment on reinforced foundation were smaller than those of the unreinforced foundation in showing the effects of geotextiles on foundation deformations.

• Tunnel and Underground Space
• /
• v.14 no.1
• /
• pp.69-77
• /
• 2004

Investigation of the time-dependent behavior of rock and the associated mechanisms are of key interest in long-term stability analysis of many engineering applications. In this study, creep tests were performed on Daejeon granite samples of 25.4mm diameter under uniaxial compression at varying stress levels. The effect of moisture was investigated by testing both air-dried and fully water-saturated samples. The creep behavior of Daejeon granite exhibited three distinctive stages of primary, secondary and tertiary creep. The ultimate strength of granite under a constant stress decreased considerably with time. Saturation and immersion of the test specimen in water markedly increased the total creep strain as well as the secondary creep rate. The experimental creep curves are fitted to Burger's model as well as two other empirical models suggested by previous researchers. A number of the parameters determined for each model are dependent on stress and influenced by the presence of water. Based on the experimental results, an empirical relation between the applied stress and the time-dependent strain is established separately for each air-dried and fully water-saturated Daejeon granite.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.37 no.1
• /
• pp.93-103
• /
• 2017

Many countries are interested in the development of the Antarctic area because of the abundant resources and living things of high research value. Korea completed the second Antarctic research station in 2014 and spurring the development of the Antarctic area by constructing runway for the airplanes and a third Antarctic research station. However, frozen soils, unlike typical soils, are sensitive to creep behavior due to the influence of ice and unfrozen water. The creep tests for evaluating creep behaviors on the frozen soils require expensive laboratory equipments and large amount of time. Thus, various empirical models had been developed to describe the unconfined compressive creep behavior of frozen soils. In this study, new analytical creep model on frozen sands was proposed by modifying Ting's Tertiary creep model with a new parameter considering fine contents. Thus, the unconfined compressive creep tests were conducted with the frozen specimens of dense Jumoonjin sand with fine contents of 0, 5, 10 and 15% under various loads at -$5^{\circ}C$, -$10^{\circ}C$ and -$15^{\circ}C$. Consequently, the modified Tertiary creep model with a new parameter for fine contents are not enough for the description of the acutal creep behavior of the frozen sand and new framework should be developed.

• Journal of the Korean Society for Heat Treatment
• /
• v.13 no.5
• /
• pp.309-317
• /
• 2000

Demand for new nondestructive evaluations is growing to detect tensile crack growth behavior to predict long term performance of materials and structure in aggressive environments, especially when they are in non-visible area. Acoustic emission technique is well suited to these problems and has drawn a keen interests because of its dynamic detection ability, extreme sensitivity and location of growing defects. In this study, we investigated the strength of fire resistance steel for frame structure by tensile test after degradation treatment and analysed acoustic emission signals obtained from tensile test with time frequency analysis methods. In the T and TN specimens(under $600^{\circ}C$-10min ) consisting of ferrite and pearlite structure, most of acoustic emission events were produced near yield point, mainly due to the dislocation activities during the deformation. However, B specimen under $600^{\circ}C$-10min had a two peak which was attribute to the presence of martensite phase. The first peak is before yield point and the second after yield point. The sources of second acoustic emission peak were the debonding of martensite-martensite interface and the micro-cracking of brittle martensite phase. In $600^{\circ}C$-30min to $700^{\circ}C$-60min, many signals were observed before yield point and were decreased after yield point.