• Journal of the Korean Institute of Gas
• /
• v.22 no.5
• /
• pp.24-30
• /
• 2018

In the case of arctic area long-distance natural gas transmission pipeline, it is necessary to construct capable facilities to maintain the gas pressure because the gas pressure is reduced according to the pipeline characteristics and route conditions. In order to maintain the proper NG pressure, it is necessary to secure economy considering the cost of main equipments of the compressor station, construction and operation cost when the compression ratio is shortened or increased by constructing the distance of the compressor station. Therefore, In this study, preliminary study on construction of arctic area long-distance transmission pipeline was reviewed and conduct conceptual design by constructing main equipments process that can reduce the construction cost of the compressor station in arctic area. In particular, in order to evaluate economic feasibility of the long-distance transmission pipeline in arctic area, the virtual area for Yakutsk~Aldan region(Russia) was supposed. The total pipeline length of the virtual is 533km, The scenarios for the location of the compressor station presented. The capacity estimated about the main equipments of the compressor station. As a result, the economic evaluation method reviewed which can minimize the construction cost of the compressor station.

• Journal of Korea Water Resources Association
• /
• v.55 no.11
• /
• pp.979-989
• /
• 2022

In hydrological surveys, observation through representative location is essential due to temporal and spatial limitations and constraints. Regarding the use of hydrological data and the accuracy of the data, there are still insufficient observatories to be used in a specific watershed. In addition, since there is virtually no standard for the location of the current evapotranspiration, this study proposes a method for determining the location of the evapotranspiration. To determining the location of evapotranspiration, a grid is selected in consideration of the operating range of the Flux Tower using the eddy covariance measurement method, which is mainly used to measure evapotranspiration. The grid of representative location was calculated using the factors affecting evapotranspiration and satellite data of evapotranspiration. The grid of representative location was classified as good, fair, and poor. As a result, the number of good grids calculated was 54. It is judged that the classification of the grid has been achieved regarding topography and land use as a characteristic that appeared in the classification of the grid. In particular, in the case of elevation or city area, there was a large deviation, and the calculated good grid was judged to be a group between the two distributions.

• Journal of the Korean Institute of Landscape Architecture International Edition
• /
• no.2
• /
• pp.178-184
• /
• 2004

The Yatomi - Aioiyama line is a city-planning road that was notified in 1957 and subsequently prepared by land readjustments. Currently, approximately 900m of road pass in the inside of the Aioiyama green area has not been constructed. The surveying briefing session for inhabitants was held in July 1992, the project was authorized by the Ministry of Land, Infrastructure and Transport in September 1993, and the project briefing session for inhabitants was held in September 1993. The site purchase has been completed. At the May 2000 briefing session, inhabitants of the area began voicing dissenting demanding the conservation of the natural environment of this green area. The inspector system serves as the third party, independent of both the administration and the inhabitants. Before finalizing the geometric line form of the road to be constructed, some surveys of animals and plants found along the walking trails carried out intensively in the northern area, which is approximately 50 ha, of the Aioiyama green area. The natural environment inspector submitted a plan for changing the geometric line form of the road decided upon by city planning, and it was approved by the city planning council. If the shelter structure or the retaining wall structure is adopted at the location where large slope faces are produced by excavation or landfill, and if the bridge structure is adopted at the place where stream-lines and walking trails intersect, it leads to a reduction of approximately $40\%$ in the areas for which change is planned. Furthermore, approximately $20\%$ of the area to be changed is restored by returning soil to the roof of the shelter.

• The Journal of Korean Academy of Prosthodontics
• /
• v.18 no.1
• /
• pp.7-13
• /
• 1980

The purpose of this study was to evaluate the removable partial denture prescriptions including surveyed crowns and design of component parts sent to the laboratory technician. A total of 351 casess with prescription forms and master cast in maxillary and mandibular semi-edentulous situations collected from dental laboratory by random sampling were selected for this study. The evaluation and study observed here involved the classification of edentulous situations, status of abutment splinting, form of rest seats and guiding plane of surveyed crows, location of maxillary major connectors and tripodig marks on the master casts. Removable partial denture prescriptions contained (1) general request (upper and lower cast framework), (2) types of metal, (3) location of retainer(retention, lingual bracing, rest area, guiding plane surface), (4) location and type of major connector, (5) relief area and amount, (6) and other specific instructions. The following informations based on the classified groups such as Group I was those cases sent with no real prescriptions. They say 'make a partial.' No prescriptions, no thought beforehand, Group II was those cases sent with a minimal prescriptions. They say 'make a partial with clasps on May be some preparations, usually inadequate. Group III was those cases sent with a moderately good prescription. Adequate but could be much better. No tripoding but it tell what clasps go where. Still not good prescriptions. Group IV was good cases, tripoded with adequate prescriptions and a prescription which exactly describes what is expected from the laboratory. The analyzed results were as follows: 1. The normal form of rest seats and guiding plane of surveyed crowns in Class. I and Class. II edentulous situations on the maxillary cast were observed 31.9% and 27.89%, respectively. The abutment teeth and retainer without occlusal rests of Class. I and Class. II were showed 11.58% and 8.86%, respectively. In mandibular cases, the normal form of rest seats and guiding plane of surveyed crowns showed 27.54% and 8.82% in Class. I and Class. II situation. The abutment teeth and retainer without rest seats were showed 15.19%, respectively. 2. The splinted surveyed crowns of Class. I and Class. II maxillary edentulous situations in distal extension cases were showed 34.51% and 28.85%, but 28.52% and 10.29%, respectively. 3. The location and type of maxillary major connector delineated on the master cast were 66 cases (44.89%). 4. The results of 351 cases were classified as Group I 146(41.59%), Group II 115 (32.76%), Group III 57 (16.23%), and Group IV 33 (9.48%). 5. The delineation of abutment tooth for clasping were 176 cases (50.14%) among total of 351 cases. 6. The delineation of height of contour line were showed 45 cases (12.8%) in Group II, 14 cases (3.98%) in Group III and 33 cases (9.40%) in Group IV with total 92 cases (26.21%). 7. In surveying procedure, the delineation of tripoding marks and reference line were showed 17 cases (4.84%).

• Journal of the Korean Institute of Rural Architecture
• /
• v.20 no.4
• /
• pp.65-75
• /
• 2018

This thesis attempts to investigate and analyse the architectural characteristics of catholic churches in Gangwon province built in the 1950s. Catholic churches built at that time in Korea had many similarities basically since they were supported by UN forces after the Korean War and were established by priests connected to the Missionary Society of St. Columban. The results of study are as follows. In location, Except one catholic church, the catholic churches preferred low and gentle hill. In layout axis, catholic churches at Youngseo area preferred the north-south layout axis, whereas those at Youngdong favor the east-west layout axis. In approach, most of catholic churches around the Youngseo and Youngdong areas preferred entering the front entrance with a bell tower, whereas three of them at Youngdong did entering the front entrance with a bell tower around the rear corner. In floor plan, catholic churches at Youngseo preferred symmetry, whereas those at Youngdong preferred asymmetry. And every floor plan of catholic churches is rectangular type with transepts except one semicircular type. In apse shape, catholic churches in the Youngseo area preferred non-extruded types like a straight wall, whereas those in Youngdong have extruded types. Every catholic churches have no crypt under ground except one at Gangreung. Except one at Sokcho, every catholic church in this study has choir space in half story.

• The Journal of the Korea Contents Association
• /
• v.6 no.12
• /
• pp.169-176
• /
• 2006

Since home network system is usually set up based on the built-in system inside home at the time of construction, it has a difficulty in being compatible with new devices after construction. In this paper, we propose DBS(Dynamic Binding System) that can make links effectively among the devices located in inside and outside of home networks. Implementation of the DBS is based on the ZigBee's binding in WPAN(Wireless Personal Area Network). For this research, we constructed the system consisting of home server that contains proxy server and location server, devices inside home in which tinyOS is embedded, and mobile device that is an emulator. The communication inside home is done by IEEE 802.15.4 protocol and the communication between servers and mobile devices outside home is done by TCP/IP protocol. Regardless of device's address format, the DBS facilitates a link among the devices located inside and outside of home networks. And, introducing a new device into home network can be recognized easily by exchanging messages between devices.

• Fire Science and Engineering
• /
• v.31 no.5
• /
• pp.19-27
• /
• 2017

The effects of changes in area and location of fire source, fire growth rate, and volume of compartment on the major fire characteristics, including heat release rate, in closed compartment fires were examined. To this end, a fire simulation using Fire Dynamics Simulator (FDS) was performed for ISO 9705 room with a closed opening. As main result, it was found that the changes in the area and location of fire source did not significantly affect the thermal and chemical characteristics inside the compartment, such as maximum heat release rate, total heat release, maximum temperature at upper layeras well as species concentrations. However, increasinthe fire growth rate and volume of compartment resulted in increase of the maximum heat release rate and total heat release, decrease in the limiting oxygen concentration and increase in the maximum CO concentration. Finally, a methodology for the application of fire growth curves to closed compartment fires was proposed by deriving the correlation of the maximum heat release rate expressed as a function of the fire growth rate and the volume ratio of compartment based on the ISO 9705 room.

• Journal of recreation and landscape
• /
• v.12 no.4
• /
• pp.67-78
• /
• 2018

Hangang Artpark construction is an enterprise founded in 2018 that involved installing public artworks created by 37 different people (teams) in Hangang Park located in Yeouido and Ichon Park. An iconic public space in Seoul, Hangang Park is turning into an even better public space due to the efforts to change the park into an eco-friendly, cultural-artistic space in tandem with the change in times. The objective of the Hangang Artpark construction business is to augment the environmental and scenic value of Hangang not only to provide a space for leisurely activities but also to revive it as a cultural-artistic area. This is a study of the concept and the design and installation processes of "Thinking of each other", a project by the Hangang Artpark construction business. This art piece has been installed in the wetlands and it trails along Ichon Hangang Park, which was created during the environmental recovery project. The piece consists of sculptures molded into animal shapes that are unique to the location and ecology of the area, displayed in harmony with the park's street furniture. By showing the coexistence of animals that existed in Hangang in the past along with the current inhabitants and the natural enemies of these inhabitants, the piece displays an ecofriendly scene. Moreover, by incorporating this piece into the street facilities of the park, such as gazebos, streetlights, surveillance cameras, and perches, the piece exhibits a different kind of street view compared to the installation style of other conventional environmental artworks. The various sculptures are installed along with the street facilities throughout the trail, rather than in a specific location intended for artworks, thereby achieving harmony with the park scene. In so doing, the piece elicits in the beholder an environment-friendly way of thinking, and at the same time, gives them a sense of calm and pleasure. Further, the paper researches the methods of safely installing art pieces in public spaces and of maintaining these installations.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.19 no.1
• /
• pp.25-43
• /
• 2016

This research was completed to provide fundamental data regarding the guidelines to installing and managing utility facilities & structures in wetland protected area to advance the functions and sustainable use of ecology services by preserving the ecology within wetland protected area. There were 5 on-site researching areas that were used as the main subject with these areas chosen and considered from 21 inland wetlands that have been designated and are being managed from the Ministry of Environment and by their designated dates as a wetland protected area. The utility facilities in these wetland areas were categorized by their types and a detailed on-site investigation was proceeded with investigation items chosen whereas these facilities are working by their roles from their location, size, used materials, types, information contents and etc., The results showed that regarding informational structures, several locations of information boards were distanced from the main exploring routes which did not consider the visitor's eye level which had their readability dropped and by sunlight, time lapse and water penetration, many information boards were damaged or corrupted so that it was hard to confirm the information noticed or understanding an image. Insufficient observation and educational structures were installed that considered the ecological characteristics of wild animals and their living conditions. Regarding convenience facilities, there were parking lots that were installed on the fore-land and to decrease non-point solution sources, some parking lots needed to be located in protected lowlands while some facilities' shape and colors did not harmonize with their natural surroundings, creating a sense of awareness, which will need some more consideration. As for safety facilities, they were very insufficient compared to other facilities. This means that additional safety structures are needed so that related personnel can be aware of where a visitor is located when an accident occurs. Protectional facilities strongly needed new structures and a management system to cut off entrances and do surveillance so that visitors do not go into areas outside of the managed areas and bring damages to restricted locations. Research labs needed to expand the use of automatic weather systems and water gauge equipments to build fundamental data regarding floodgates that are intimated to the forming of wetlands. Sensor cameras and other types of monitoring systems are needed to monitor the majority types of animals living in the wetlands as well.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.17 no.5
• /
• pp.1-9
• /
• 2013

Variable area nozzle, where both throat and exit area vary, is required for optimal expansion and optimal nozzle shape upon operation of after-burner. Steady-state and transient analyses are carried out for each condition with and without afterburner operation and as a function of the location of the nozzle flap. Effects of that nozzle displacement on flow and thrust characteristics are analyzed from numerical results. With variable area nozzle adopted, the combustion field is variable in time, leading to periodically variable thrust. For off-design conditions, flow separation shows up due to over expansion at the flap tips and shock wave does in the nozzle due to under expansion. The undesirable phenomena can be solved by control of variable area nozzle.