• Magazine of the Korean Society of Agricultural Engineers
• /
• v.12 no.4
• /
• pp.2090-2123
• /
• 1970

This paper is a report on the research of experimental model test of Andong Fill Dam, which has been planned by the Government of Korea as a project, of its over-flowing capacity in spillway, creation of minus pressure and structure of anti-water impulse in over-flow weir. Andong Fill Dam is one of the project of master development plant for water resources, locating at Nakdong River side of Korea, and is aimed to have a multi-purpose dam for flood-control, irrigation, water power, urban and industrial water supply. This dam is planned to erect in fill-dam type due to the improper soil foundation and condition for concrete dam. The refore for the proper and advantageous points, this is designed as center core fill dam. By a model minimized of Andong Fill Dam, held an experimental model test on water quentity of reservir, discharges of overflow part, low pressure and anti-water impulse of overflow part, which was conducted an experiment by flowing aspects through each section of spillway to find the changes of water pressure and that of water level, and corrected the section of each part in order to conduct a check on the creation of minus pressure not to be over acted to the allowable bundary of the section structure; and for the prevention of concentated scouring at the down stream side of flow.

• Journal of Powder Materials
• /
• v.1 no.2
• /
• pp.159-166
• /
• 1994

The variation of the microstructures and the mechanical properties with varying vacuum hot pressing temperature and pressure was investigated in PyM processed 20 vol%) SiCw/ 2124Al composites. As increasing the vacuum hot pressing temperature, the aspect ratio of whiskers and density of composites increased due to the softening of 2124Al matrix with the increased amount of liquid phase. The tensile strength of composite increased with increasing vacuum hot pressing temperature up to $570^{\circ}C$ and became saturated above $570^{\circ}C$, To attain the high densification of composites above 99%, the vacuum hot pressing pressure was needed to be above 70 MPa. However, the higher vacuum hot pressing pressure above 70 MPa was not effective to increase the tensile strength due to the reduced aspect ratio of SiC whiskers from damage of whiskers during vacuum hot pressing. A phenomenological equation to predict the tensile strength of $SiC_w$/2124AI composite was proposed as a function including two microstructural parameters, i.e. density of composites and aspect ratio of whiskers. The tensile strength of $SiC_w$/2124AI were found more sensitive to the porosity than other P/M materials due to the higher stress concentration and reduced load transfer efficiency by the pores locating at whisker/matrix interfaces.

• Economic and Environmental Geology
• /
• v.17 no.2
• /
• pp.101-107
• /
• 1984

This paper describes dipole-dipole apparent resistivity responses from near-surface cavities in otherwise homogeneous earth materials. In applying the dipole-dipole resistivity method to the problem of locating and delineating subsurface cavities, it is important to know apparent resistivity responses not only for conductive bodies but also for resistive ones. Dipole-dipole apparent resistivities for these bodies are calculated by the numerical modeling technique using an integral equation solution. The magnitude and pattern of apparent resistivity is highly dependent on the ratio of body resistivity to background resistivity. In conductive bodies, the largest anomaly of apparent resistivity appears at the outside of the body. In resistive bodies, however, the position of the largest anomaly coincides with the location of the body. The field results gathered at Okinawa, Japan in 1978 showed that peak anomalies occurred at the locations of air-filled cavities.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.21 no.2
• /
• pp.147-154
• /
• 2003

The close-range photogrammetry is a surveying technique the acquiring the 3D object from 2D geometric appearance shown in the image. Camera treatment is relatively so simple. Camera position refer to the object can be freely adjusted by locating the exposure station at any site. So it is used effectively on a small area or object for survey. In this study, using the digital camera which has capacity of keeping numerical value by itself and easy carrying, we analyze the positioning error according to various change of photographing condition. Also we try to find a effective method of acquiring basis data for 3D monitoring of high-accuracy in sub-pixel degree thorough digital close-range photogrammetry with bundle adjustment for local terrain model generation.

• Communications of the Korean Institute of Information Scientists and Engineers
• /
• v.5 no.1
• /
• pp.42-49
• /
• 1987

This paper describes test-pattern generation and it;s sequence for fan out-free Combinational logic network with multiple faults. The method for detecting multiple faults, in systematic way, is established by using characteristic graphs. This method is applied even in the case of fan out-reconvergent combinational logic networks. In this case, the network is decomposed into a set of fan out-free sybnetworks so as to use the characteristic graphs, and minimal test patterns are generated seperately. The each test set is combined and the test pattern for fan out-reconvergent networks are derived. According to corresponding characteristic graph, additional test patterns to detect multiple faults are simply derived.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.14 no.5
• /
• pp.12-18
• /
• 2000

This paper describes the analysis of ultrasonic signal and partial discharge(PD) signal patterns for each location of particle in GIS. The characteristics of the ultrasonic signal and PD signal patterns for each location were as follows; in case of particle on the electrode, large ultrasonic signals and large PD signals occurred in positive half-cycle periodically; in case of particle on the spacer, ultrasonic signals and large PD signals occurred in negative half-cycle periodically; in case of the free moving particle, ultrasonic signals and large PD signals occurred by collision non-periodically. As a result, it was confirmed that particle in GIS could be located by the comparison and analysis of ultrasonic signal and PD signal patterns.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.10 no.4
• /
• pp.1630-1642
• /
• 2016

Inter-domain routing is the most critical function of the Internet. The routing system is a logical network relying on the physical infrastructure with geographical characteristics. Nature disasters or disruptive accidents such as earthquakes, cable cuts and power outages could cause regional failures which fail down geographically co-located network nodes and links, therefore, affect the resilience of inter-domain routing system. This paper presents a model for regional failures in inter-domain routing system called REFER for the first time. Based on REFER, the resilience of the inter-domain routing system could be evaluated on a finer level of the Internet, considering different routing policies of intra-domain and inter-domain routing systems. Under this model, we perform simulations on an empirical topology of the Internet with geographical characteristics to simulate a regional failure locating at a city with important IXP (Internet eXchange Point). Results indicate that the Internet is robust under a city-level regional failure. The reachability is almost the same after the failure, and the reroutings occur at the edge of the Internet, hardly affecting the core of inter-domain routing system.

• Proceeding of Spring/Autumn Annual Conference of KHA
• /
• 2008.04a
• /
• pp.272-275
• /
• 2008

In case a middle school music room locating in Iksan City, this space had been finished its construction work with the indiscreet sound-absorbing materials despite the music lesson is taught thereat. Accordingly, when music lesson since it sounds aridly due to insufficiency of echo and sound-volume feeling in music appreciation or music performance sound, there is some difficulty in the music lesson. For the purpose to control the obstructive factors owing to such short Reverberation Time, it optimizes the acoustic factor using Acoustic Simulation after arrangement of Acoustic Design, it has conducted a Psycho-acoustics Experiment using the Auralizational Technique that can experience the Virtual Acoustic Field at its designing stage. As the result of investigation about the acoustic satisfaction on the relevant subject space and the satisfaction with regard to the pertinent each items, it was known that the valuation on acoustic performance was evidently improved at 'after-reformation' than 'before-reformation'. It is considered that such material could be utilized as the useful material that can improve the architectural acoustic factor when construction and renovation of any middle school music room in the future.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2003.05a
• /
• pp.125-128
• /
• 2003

This study aims to feasibility study of the Youth Center. Welfare of adolescents is appeared to a matter of concern and interest as social problems of various kinds related adolescents including the fire at a beer bar in Inchon occur recently. In view of government, in addition to fairness of facility location, location of such facilities are to be determined the respect to cost of locating facilities and developmental direction in the future. A feasibility study is an effective tool in determining the decision of investment or not and the level of investment priority on projects requiring a sizeable investment and the feasibility of a project. The first, it is to select reasonable location. It was selected three and two by consideration of facilities distribution and connection with others. Five proposal selected was estimated by five element of approach, demand, symbol, reality, environment. In result proposal I was chosen. The next, it is to estimate scales. It was estimated by analysis of catchment area, similar facilities, programs, in result 7,260$m^2$ cone into analysis to the best gross area The finally, it is to study on economical efficiency. Income Statement estimated was came out \1.7billion. in addition, it offer various benefit by public facilities.

• Imaging Science in Dentistry
• /
• v.50 no.3
• /
• pp.183-192
• /
• 2020

Purpose: This study was performed to assess the accuracy of preoperative cone-beam computed tomography (CBCT), when justified for other reasons, in locating the apical foramen and establishing the working length. Materials and Methods: Six electronic databases were searched for studies on this subject. All studies, of any type, were included if they compared measurements of working length with preoperative CBCT to measurements using an electronic apex locator (EAL) or histological reference standard. Due to the high levels of heterogeneity, an inverse-variance random-effects model was chosen, and weighted mean differences were obtained with 95% confidence intervals and P values. Results: Nine studies were included. Compared to a histological reference standard, CBCT indicated that the apical foramen was on average 0.40 mm coronal of its histological position, with a mean absolute difference of 0.48 mm. Comparisons were also performed to an EAL reference standard, but the conclusions could not be considered robust due to high levels of heterogeneity in the results. Conclusion: A low level of evidence is produced suggesting that preoperative CBCT shows the apical foramen to be on average 0.40 mm coronal to its histological position, with a mean absolute difference of 0.48 mm.