• Journal of the Earthquake Engineering Society of Korea
• /
• v.24 no.6
• /
• pp.253-266
• /
• 2020

The extended slip-weakening model was investigated by using a compiled set of source-spectrum-related parameters, i.e. seismic moment M_o, S-wave velocity V_s, corner-frequency f_c, and source-controlled high-cut frequency fmax, for 113 shallow crustal earthquakes (focal depth less than 25 km, M_W 3.0~7.5) that occurred in Japan from 1987 to 2016. The investigation was focused on the characteristics of stress drop, radiation energy-to-seismic moment ratio, radiation efficiency, and fracture energy release rate, G_c. The scaling relationships of those source parameters were also investigated and compared with those in previous studies, which were based on generally used singular models with the dimensionless numbers corresponding to f_c given by Brune and Madariaga. The results showed that the stress drop from the singular model with Madariaga's dimensionless number was equivalent to the breakdown stress drop, as well as Brune's effective stress, rather than to static stress drop as has been usually assumed. The scale dependence of stress drop showed a different tendency in accordance with the size category of the earthquakes, which may be divided into small-moderate earthquakes and moderate-large earthquakes by comparing to M_o = 10¹⁷~10¹⁸ Nm. The scale dependence was quite similar to that shown by Kanamori and Rivera. The scale dependence was not because of a poor dynamic range of recorded signals or missing data as asserted by Ide and Beroza, but rather it was because of the scale dependent V_r-induced local similarity of spectrum as shown in a previous study by the authors. The energy release rate G_c with respect to breakdown distance D_c from the extended slip-weakening model coincided with that given by Ellsworth and Beroza in a study on the rupture nucleation phase; and the empirical relationship given by Abercrombie and Rice can represent the results from the extended slip-weakening model, the results from laboratory stick-slip experiments by Ohnaka, and the results given by Ellsworth and Beroza simultaneously. Also the energy flux into the breakdown zone was well correlated with the breakdown stress drop, ${\tilde{e}}$ and peak slip velocity of the fault faces. Consequently, the investigation results indicate the appropriateness of the extended slip-weakening model.

• Journal of the Korean earth science society
• /
• v.23 no.7
• /
• pp.565-574
• /
• 2002

Based on previous investigations of aerial photographs and topographical surveys, this study focuses on the sedimentologic features of the Daebudo area including sedimentation processes, sedimentary facies and hydrologic conditions of the erosional coast. A total of 137 surface sediments and one core (by hand auger) sediment were obtained to interpret the depositional environment of the erosional coast in the macro-tidal coast. Surface sediments are distributed from sandy gravel (sG) to silt (Z). Textural parameters are characterized not only by coarse, poorly sorted, positive skewed and multi-modal distribution in the supra-tidal flat, but also finer, relatively well-sorted, symmetric distribution in the intertidal flat. According to the C/M diagram, sediment transport modes of study area are characterized by the mixed mode of suspension and bedload in the upper-, middle-tidal flat and by uniform suspension in the lower-tidal flat due to tidal effect. Vertical sediment distribution of the core, collected near shoreline, shows coarsening-upward, poorly sorted pattern by the input of detritus resulting from coastal erosion. Considering the sedimentological features of the study area, it appears to be composed of a coastal zone changed by not only artificial reclamation, but also by natural processes such as strong wave action due to typhoons and storms during high water level and long/short-term sea level rising. As a result, tide-dominated erosional coasts show that the shore is affected by local, temporal and hydrological conditions near high tide level and that the intertidal flat is represented by a general tide-dominated sedimentary environment.

• Journal of Soil and Groundwater Environment
• /
• v.10 no.6
• /
• pp.45-55
• /
• 2005

The geothermal research has been carried out on the Heunghae, Pohang geothermal area know as having geo-heat-flow area in the Korean peninsula. This study results so far indicate that geothermal water in the area is in peripheral waters of hydrothermal area and is not in equilibrium with the reservoir rock. The average oxygen and hydrogen stable isotope values are as follows: deep groundwater $(average:\;{\delta}^{18}O=-10.1\%_{\circ},\;{\delta}D=-65.8\%_{\circ})$, intermediate groundwater (average: $(average:\;{\delta}^{18}O=-8.9\%_{\circ},\;{\delta}D=-59.6\%_{\circ})$, shallow groundwater $(average:\;{\delta}^{18}O=-8.0\%_{\circ},\;{\delta}D=-53.6\%_{\circ})$, surface water $(average:\;{\delta}^{18}O=-7.9\%_{\circ},\;{\delta}D=-53.3\%_{\circ})$ respectively. Deep groundwaters was originated from a local meteoric water recharged from distant, topographically high mountain region and not affected by the sea water. High temperature zone inferred from water geothermometers is around D-1, D-5, D-6, 1-04 well zones. The estimated enthalpy from Silica-enthalpy mixing model is near 410 kJ/kg, which corresponds to the temperature of $98^{\circ}C$, and in consistent with the result of Na-K and K-Mg geothermometer.

• Proceeding of Spring/Autumn Annual Conference of KHA
• /
• 2009.11a
• /
• pp.132-137
• /
• 2009

The purpose of this study was to suggest urban regeneration methods for deteriorated downtown residential area, considering the development condition of urban blocks. Through the research that are based on literature, field survey, urban planning map and local experts consulting, it found out suitable sites for development such as a deteriorated residential zone or a unused site and it was deduced eight development types from analyzing the characters of developable sites. And then it is suggested various housing forms which were applied to eight development types of developable sites. The consequences of this research are summarized as follows. There are various housing forms by eight development types; block housing, low rise-high density court housing, medium low rise-high density housing, urban housing for low-income groups belong to T1-development of urban strategic position; block housing, housing on hilly site, semi-detached house, lodging house, urban housing for low-income groups, elderly housing belong to T2-development for living benefit; block housing, low rise-high density court housing, housing on hilly site, low rise housing, lodging housing, urban housing for low-income groups, elderly housing belong to T3-development of a small-scale rental housing; block housing, low rise-high density court housing, medium low rise-high density housing, terrace-house, housing on hilly site, low rise housing, block-typed detached house, semi-detached house, cluster-typed low rise housing, town house, urban housing for low-income groups belong to T4-residential environment renewal development; terrace-house, housing on hilly site, low rise housing, block housing, semi-detached house belong to T5-development of a small-scale housing; terrace-house, housing on hilly site, low rise housing, cluster-typed low rise housing belong to T6-development to adapt natural environment; block housing, low rise-high density court housing, low rise housing, block-typed detached house, town house belong to T7-development for community; block housing, low rise-high density court housing block housing, medium low rise-high density housing, terrace-house, housing on hilly site, low rise housing, elderly housing belong to T8-development of environment-friendly.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.7 no.1
• /
• pp.93-101
• /
• 1987

Residual stresses have remained around welding areas of a steel structure member after welding operation. The major causes to occur these residual stresses are the local heat due to a welding, the heat stresses due to a irregular and rapid cooling condition, the material and rigidity of a steel structure. Ultimatly, these residual stresses have been known to decrease a brittle fracture strength, a fatigue strength, a buckling strength, dynamic properties, and the corrosion resistance of the material. This paper deals with the residual stresses on a steel structure member through experimental studies. SWS 58 plates were welded by the method of X-groove type. These plates were layed on the heat treatment at four different temperatures; $350^{\circ}C$, $500^{\circ}C$, $650^{\circ}C$ and $800^{\circ}C$. The resulting residual Stresses were measured by hole drilling method, and the followings were obtained. The residual stresses on the vicinity of a welding point were relieved most effectively at the temperature of $650^{\circ}C$, and these stresses relieved completly when the ratio of a hole diamerter to a hole depth became unity. Hardness test shows that the higher value of hardness at the heat affected zone dropped to belower as the temperature went up from $350^{\circ}C$ to $800^{\circ}C$. The Welding input heats have not influenced the magnitude of residual stresses at the input heat range between above and below one forth than standard.

• Economic and Environmental Geology
• /
• v.22 no.4
• /
• pp.381-393
• /
• 1989

Hydrogeological modelling was performed to evaluate groundwater flow system in Igsan Area. The study area extends over $790km^2$. The geology consists of Jurassic Daebo granite and gneissose granite and Precambrian metamorphic rocks. The capability of pumping yield is the highest in gneissose granite region among them due to comparatively thick weathered zone with thickness ranging from 10m to 25m. The Colorado State University Finite Difference Model was used for the model simulation. The model was divided into 28 rows and 31 columns with variable grid spacing. The model was calibrated under steady-state and unsteady-state conditions. In the steady-state simulation, the model results were compared with measured water table contours in September 1985 with determining hydraulic conductivities and net recharge rates during rainy season. Unsteady state simulation was done to know the aquifer response due to groundwater abstraction. The non- steady state calibration was conducted to determine the distribution and magnitudes of specific yields and discharge/recharge rates during dry season as matching water level altitudes in May 1986. The calibrated model was used to simulate water level vaiation caused by groundwater withdrawal and natural recharge from 1 October, 1985 until 30 September, 1995. The calibrated model can be used to groundwater development schemes on regional groundwater levels, but it cannot be used to simulate local groundwater level change at a specific site.

• Journal of Korean Society of Disaster and Security
• /
• v.12 no.3
• /
• pp.25-34
• /
• 2019

Modern disasters prevent accidents in advance and recover after accidents are very important. Our government's current response to these accidents is not appropriate. As for disaster management so far, it has been the center of disaster response and recovery efforts, and has been led by the government against it. The reality is that most private organizations and agencies have only subsidized government disaster management agencies. Korea is no longer a safe zone for earthquakes. Now for the establishment of effective disaster management system for earthquakes in the diagnosis is very urgent and the problems of the operational disaster management, which the problems of the nation.Policies to improve academic efforts to seek alternative proposal is also at a time when volume can be said to be very big need to mine. This study from 2016 to 2019, about the earthquake that took place between National Statistical Office, based on analysis of data to. First of all, research 1: What was the government's plan on Pohang earthquake? The results showed that the residents' evacuation of Pohang was important in the Pohang earthquake, but for the sake of students' safety, they were directly assigned to the test site to cope with the emergency situation. Therefore, the research and analysis shows that the nation should continue to think about the causes and responses of the damage at the disaster site and strive to develop technologies and methods to minimize the damage.

• Agribusiness and Information Management
• /
• v.9 no.2
• /
• pp.1-11
• /
• 2017

Introduction: To analyze the impact of marketing losses on efficiency in transacting banana in Kurnool district of SRZ in Andhra Pradesh and to assess the opinions of the farmers on the constraints in transacting banana. Research back ground, Materials and Methods: The study relies exclusively on primary information obtained from the banana farmers of Kurnool District. Purposive sampling procedure was followed for the selection of the study area. Top two mandals in the district and top two villages in each mandal are selected in accordance with the area under cultivation of banana. Probability proportion to size was followed regarding the selection of sample farmers and accordingly 60 marginal, 37 small and 23 other farmers were selected and thereby, the total sample size was 120. Result and Discussion: Three marketing channels were identified in the marketing of banana in Kurnool district viz., Producer ${\rightarrow}$ Local-exporter ${\rightarrow}$ Wholesaler ${\rightarrow}$ Retailer ${\rightarrow}$ Consumer (Channel-I), Producer ${\rightarrow}$ Wholesaler ${\rightarrow}$ Cart-vendor ${\rightarrow}$ Consumer (Channel-II) and Producer ${\rightarrow}$ Juice-holder ${\rightarrow}$ Consumer (Channel-III). With the inclusion of marketing losses in the price spread analysis of banana in all the three channels, the marketing costs of all the intermediaries were increased and thereby, the farmer's share in consumer's rupee and Net Marketing Margins of the agencies are on the decline. So, without inclusion of marketing losses, the farmer's share in consumer's rupee and Net Marketing Margins of all the agencies are overvalued. The higher the marketing losses, the more is the negative impact on farmer's net selling price, net marketing margins of the intermediaries and marketing efficiency. The sample farmers are facing major problems in marketing of banana like frequent price fluctuations, unorganized marketing and lack of transportation facilities on priority basis. Suggestions: It is suggested to educate the farmers regarding the optimum maturity index for harvest, use of mechanical harvesters, proper placement of fruits during storage and ripening, better packaging and cushioning technologies to absorb shocks during transportation, strengthening of storage facilities and transport facilities, encourage co-operative marketing etc., to promote marketing efficiency of banana in the study area.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.39 no.5
• /
• pp.48-56
• /
• 2011

The objective of this study is to develop quantitative criteria for setting reasonable standards and regulations for building heights in collective facility districts inside national parks or those connected to their borders. Heights of all building sin collective facility districts were simulated in order to determine heights of ridge lines of sight passing the upper parts of buildings from a main view point. Where a facility's zone is located at the inside or boundary of inland mountainous national parks, and there are coastal type national parks with mountains in the background, the study recommended assigning the maximum allowable height of a building as 8.82m if national park authorities intend to preserve the ridges at three-tenths the height of a mountain. It amounts to 3 or 3.5 stories when it is converted into the number of floors. It is desirable to apply this standard to accommodations like a hotel except lodge or cottage as the maximum allowable height of a building. Nevertheless, when there aren't back mountainous areas among coastal-type national parks, there is a need for applying a separate standard. If an equal and uniform standard is applied to all collective facility districts, it becomes difficult to address local differences when managing landscape. There must be flexibility when applying a standard, depending on variables such as location of view points, differences in the methods of selection of view points, and differences in view angles, etc. Thus, there is a need for different landscape management strategies that address the unique natural environment of different zones.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.9 no.2
• /
• pp.59-71
• /
• 2006

Due to the rapid process of industrialization the cities of Korea confront changes of climate, destructions of the habitate and decrease of the green. Recently Seoul and other local governments have implemented policies and projects to improve the environmental surroundings. In reality, however, those policies and projects face difficulties in the course of implementation. The fact that there are no concrete regulations and specific legal procedures turns out to be one of the main difficulties. The aim of this study is to present specific plans and methods of wall-planting and to provide basic guidelines for the future direction of wall-planting and offer ideas of facilitating wall-planting. This study is based on questionnaires from specialists of landscape architecture through individual interviews and/or e-mails. The questionnaire is consisted of following 4 sections. 1. Show the experts current regulations and/or legal procedures and ask them improvements and suggestions. 2. Ask them choose matters of the highest priority by using Ricardo's diagram method. 3. Ask them to make a graded list in terms of the location and method of wall-planting. 4. Study the maketability of the wall-planting products currently in circulation. The city of Seoul and the Ministry of Environment recommend that trellis and/or planting inducement structures be installed on the building wall by regulation. The specialists responded to the questionnaire advocate that green wall without trellis should be allowed as green zone. Therefore regulations concerning the wall-planting should be determined specifically according to the characteristics of individual plants and walls. It has been urged that legal aid and social support must be reinforced to establish rules dealing with wall-planting. The respondents also point out that significant cutting down of the tax is far more effective in accelerating the wall-green instead of administrative support. The highest priority in terms of planting has been given to sound-proof wall, retaining wall and building wall. Concerning the maketability of the wall-planting products, panel products are recommended for early-planting and building planting. It has been suggested that the research and study of new materials and species be done in advance.