• Journal of Institute of Control, Robotics and Systems
• /
• v.19 no.7
• /
• pp.653-660
• /
• 2013

This paper deals with the problem of unfairness among uplink TCP (Transmission Control Protocol) flows associated with frame aggregation employed in IEEE 802.11n WLANs (Wireless Local Area Networks). When multiple stations have uplink TCP flows and transmit TCP data packets to an AP (Access Point), the AP has to compete for channel access with stations for the transmission of TCP ACK (acknowledgement) packets to the stations. Due to this contention-based channel access, TCP ACKs tend to be accumulated in the AP's downlink buffer. We show that the frame aggregation in the MAC (Medium Access Control) layer increases TCP ACK losses in the AP and leads to the serious unfair operation of TCP congestion control. To resolve this problem, we propose the TAC (TCP ACK Compression) mechanism operating at the top of the AP's interface queue. By exploiting the properties of cumulative TCP ACK and frame aggregation, TAC serves only the representative TCP ACK without serving redundant TCP ACKs. Therefore, TAC reduces queue occupancy and prevents ACK losses due to buffer overflow, which significantly contributes to fairness among uplink TCP flows. Also, TAC enhances the channel efficiency by not transmitting unnecessary TCP ACKs. The simulation results show that TAC tightly assures fairness under various network conditions while increasing the aggregate throughput, compared to the existing schemes.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.14 no.6
• /
• pp.235-243
• /
• 2014

In this paper, we propose an efficient control system for intelligent LED indoor lighting. The proposed an efficient control system for intelligent LED indoor lighting were included to elements such as daylight intensity measured through the PIR sensor and illuminance sensor at lighting style by the schedule defined and the occupancy detection. And it was controlled lighting through to the wireless sensor network, and was designed for the energy savings. Also, the lighting control of indoor lighting based on occupancy detection detect fine movements using a PIR sensor. And an unnecessary lighting intensity control of the window-side and the inside were controlled according to daylight level measurement result using the light sensor. In daylight inflow many case, the window-side lighting was to automatically darker, and in daylight inflow less case, was designed to be automatically bright. The efficiency validate results of an efficient control system for intelligent LED indoor lighting, the brightness of the indoor light were to maximize the energy saving by controlling in real time when entering as indoor a little that external lighting or daylight.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.3 no.2
• /
• pp.89-95
• /
• 2003

In this paper, we have designed and fabricated high conversion gain Q-band active sub-harmonic mixers for a receiver of millimeter wave wireless communication systems. The fabricated active sub-harmonic mixer uses 2nd harmonic signals of a low local oscillator (LO) frequency. The fabricated mixer was successfully integrated by using $0.1{\;}\mu\textrm{m}$GaAs pseudomorphic high electron mobility transistors (PHEMTs) and coplanar waveguide (CPW) structures. From the measurement, it shows that maximum conversion gain of 4.8 dB has obtained at a RF frequency of 40 GHz for 10 dBm LO power of 17.5 GHz. Conversion gain from the fabricated sub-harmonic mixer is one of the best reported thus far. And a phase noise of the 2nd harmonic was obtained -90.23 dBc/Hz at 100 kHz offset. The active sub-harmonic mixer also ensure a high degree of isolations, which are -35.8 dB from LO-to-IF and -40.5 dB from LO-to-RF, respectively, at a LO frequency of 17.5 GHz.

• Journal of the Institute of Electronics Engineers of Korea CI
• /
• v.49 no.4
• /
• pp.82-88
• /
• 2012

A VANET (Vehicular Ad Hoc Network), a subclass of MANET (Mobile Ad Hoc Network), is an ad hoc network using wireless communication between vehicles without fixed infrastructure such as base station. VANET suffers a frequent link breakage and network topology change because of the rapid movement of vehicles and the density change of vehicles. From these characteristics of VANET, geographical routing protocols such as GPSR (Greedy Perimeter Stateless Routing) using only the information of neighbor nodes are more suitable rather than AODV and DSR that are used in existing MANETs. However, GPSR may have a transmission delay and packet loss by frequent link disconnection and continual local maxima under the low vehicle density conditions. Therefore, in this paper, we propose a DTVR (Delay Tolerant Vehicular Routing) algorithm that perform a DTN-based routing scheme if there is no 2-hop neighbor nodes for efficient routing under the low vehicle densities in VANETs. Simulation results using ns-2 reveal that the proposed DTVR protocol performs much better performance than the existing routing protocols.

• Journal of IKEEE
• /
• v.19 no.1
• /
• pp.18-26
• /
• 2015

In this paper, we proposed and evaluated the performance of an internal MIMO (Multiple Input Multiple Output) antenna for multiband operations including LTE (Long Term Evolution) 700/2300/2500. And to enhance the isolation characteristic, a parasitic element is designed and applied. The proposed single antenna has a volume of $60mm(W){\times}38mm(L)$, and the ground plane is $60mm(W){\times}100mm(L)$. The parasitic element used for enhancing the isolation of the antenna was designed with a copper on FR4 sized $60mm(W){\times}20mm(L){\times}1.6mm(H)$, and the pattern size is $60mm(W){\times}15mm(L)$. Simulated and measured results showed that LTE 700/2300/2500, DCS (Digital Cellular Service: 1710-1880MHz), K-PCS (Korea-Personal Communication Service: 1750-1870MHz), US-PCS (US-Personal Communication Service: 1850-1990MHz), WCDMA (Wideband Code Division Multiple Access: 1920-2170MHz), Wibro (2300-2390MHz), Bluetooth (2400-2483MHz), WLAN (Wireless Local Area Network: 2400-2483.5MHz), US-WiMAX (US-World interoperability for Microwave Access: 2400-2590MHz) frequency bands were covered with $S_{11}$ values less than -6dB (VSWR < 3). Simulated and measured results on $S_{21}$ at 730MHz for the firstly designed MIMO antenna showed -5.50dB and -5.65dB, respectively. When with the parasitic element at the separated ground plane to enhance the isolation performance, -10.33dB and -12.90dB are obtained for the simulation and measurement, so the enhanced isolation performance at lower frequency band (617-867MHz) is confirmed.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.5 no.5
• /
• pp.869-876
• /
• 2001

In modern wireless communication, it has been regarded as a important problem for the spectrum efficiency to utilize the limited frequency-resource efficiently. In addition, the system architecture has been designed for low cost, low power consumption and ultra-lightweight. In this paper, we directly modulated the BCPFSK with a superior spectrum efficiency using the DDS and applied the direct conversion to the system architecture. Finally, we designed a transceiver which has the 433 MHz BCPFSK output and evaluated the system performance. In the measured result, we know that as for spectrum and the power efficiency, BCPFSK method is better than conventional one. Also, the results of the designed system is 433.92 MHz in center frequency and about 33 dBc in carrier suppression ratio. And we get the better results in local oscillator leakage and the spurious of the ISM out-band the same as -69dBc and under 60dBc.

• Journal of KIISE:Information Networking
• /
• v.29 no.3
• /
• pp.277-285
• /
• 2002

This paper proposes and analyzes an error control scheme for the transmission control based real-time communication, such as FDDI, TDMA, and wireless LAN, which delivers the message according to the round robin fashion after the off-line bandwidth allocation. Taking into account the time constraint of each message, the proposed error control scheme makes the receiver transmit the error report via asynchronous traffic while the sender resend the requested message via overallocated access time which is inevitably introduced by the bandwidth allocation procedure for hard real -time guarantee. The error control procedure does not interfere other real -time message transmissions. In addition, as each frame contains the size of the message it belongs, the receiver can recognize the end of completion of message transmission. This enables earlier error report to the receiver so that the sender can cope with more network errors. The analysis results along with simulation performed via SMPL show that the proposed scheme is able to enhance the deadline meet ratio of messages by overcoming the network errors. Using the proposed error control scheme, the hard real -time network can be built at cost lower than, but performance comparable to the expensive dual link network.

• Journal of Institute of Control, Robotics and Systems
• /
• v.20 no.6
• /
• pp.676-688
• /
• 2014

The IEEE 802.11e EDCA (Enhanced Distributed Channel Access) mechanism has been proposed to improve the QoS (Quality of Service) of various services in WLANs (Wireless Local Area Networks). By differentiating the channel access delay depending on ACs (Access Categories), this mechanism can provide the relative service differentiation among ACs. In this paper, we consider that WLAN is deployed in medical environments to transfer medical traffic and we reveal that the quality of the medical traffic (in particular, ECG signals) is significantly deteriorated even with the service differentiation by IEEE 802.11e EDCA. Also, we analyze the reason for performance degradation and show that IEEE 802.11e EDCA has difficulty in protecting the transmission opportunity of high-priority traffic against low-priority traffic. In order to assure medical-grade QoS, we firstly define the service priority of medical traffic based on their characteristics and requirements, and then we propose the enhanced channel access scheme, referred to as DIFF-CW. The proposed scheme differentiates CW (Contention Window) depending on the service priority and modifies the channel access procedure for low-priority traffic. The simulation results confirm that the DIFF-CW scheme not only assures the QoS of medical traffic but also improves the overall channel utilization.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.6 no.5
• /
• pp.611-620
• /
• 2011

A planar monopole antenna that was developed for WLAN/WiMAX application is presented in this paper. The proposed antenna with three strips, an asymmetrical ground plane, and a rectangular slit in the ground is designed to cover the popular frequency spectrum of WLAN (wireless local area network) bands and WiMAX (Worldwide Interoperability for Microwave Access) bands. The proposed antenna, which is capable of wideband operation, is fed by a strip line and fabricated on an FR-4 substrate. The obtained numerical results agree well with the experiment data. It was validated that the configuration can meet the demands for the WLAN/WiMAX systems and effectively enhanced the impedance bandwidth to 9.95% for the lower band and 76.05% for the upper band for VSWR < 1 : 2. This paper also presents and discusses the 2D radiation patterns and 3D gains according to the results of the experiment.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.12 no.6
• /
• pp.1049-1056
• /
• 2017

In this paper, a microstrip-fed dual-band monopole antenna with two arc-shaped lines for WLAN(: Wireless Local Area Networks) applications was designed, fabricated and measured. The proposed antenna is based on a microstrip-fed structure, and composed of two arc-shaped lines and then designed in order to get dual band characteristics. We used the simulator, Ansoft's High Frequency Structure Simulator(: HFSS) and carried out simulation about parameters L2, L5, and with/without slit to get the optimized parameters. The proposed antenna is made of $13.0{\times}34.0{\times}1.0 mm^3$ and is fabricated on the permittivity 4.4 FR-4 substrate($12.0{\times}34.0{\times}1.0mm^3$). The experiment results are shown that the proposed antenna obtained the -10 dB impedance bandwidth 360 MHz (2.29~2.65 GHz) and 1,245 MHz (4.705~5.95 GHz) covering the WLAN bands. Also, the measured gain and radiation patterns characteristics of the proposed antenna are presented at required dual-band(2.4 GHz band/5.0 GHz band), respectively.