• Steel and Composite Structures
• /
• 제2권3호
• /
• pp.171-194
• /
• 2002

In this paper, the behaviour of axially loaded partially encased composite columns made with light welded H steel shapes is examined using ABAQUS finite element modelling. The results of the numerical simulations are compared to the response observed in previous experimental studies on that column system. The steel shape of the specimens has transverse links attached to the flanges to improve its local buckling capacity and concrete is poured between the flanges only. The test specimens included 14 stubcolumns with a square cross section ranging from 300 mm to 600 mm in depth. The transverse link spacing varied from 0.5 to 1 times the depth and the width-to-thickness ratio of the flanges ranged from 23 to 35. The numerical model accounted for nonlinear stress-strain behaviour of materials, residual stresses in the steel shape, initial local imperfections of the flanges, and allowed for large rotations in the solution. A Riks displacement controlled strategy was used to carry out the analysis. Plastic analyses on the composite models reproduced accurately the capacity of the specimens, the failure mode, the axial strain at peak load, the transverse stresses in the web, and the axial stresses in the transverse links. The influence of applying a typical construction loading sequence could also be reproduced numerically. A design equation is proposed to determine the axial capacity of this type of column.

• Smart Structures and Systems
• /
• 제23권6호
• /
• pp.653-667
• /
• 2019

Using cross-ties to connect cables together when forming a cable network is regarded as an efficient method of mitigating cable vibrations. Cross-ties have been extended and fixed on bridge decks or towers in some engineering applications. However, the dynamics of this kind of system need to be further studied, and the effects of extending cross-links to bridge decks/towers on the modal response of the system should be assessed in detail. In this paper, a system of two cables connected by an inter-supported cross-link with another lower cross-link extended to the ground is proposed and analyzed. The characteristic equation of the system is derived, and some limiting solutions in closed form of the system are derived. Roots of cable system with special configurations are also discussed, attention being given to the case when the two cables are identical. A predictable mode behavior was found when the stiffness of inter-connection cross-link and the cross-link extended to the ground were the same. The vector of mode energy distribution and the degree of mode localization index are proposed so as to distinguish global and local modes. The change of mode behaviors is further discussed in the case when the two cables are not identical. Effects of cross-link stiffness, cross-link location, mass-tension ratio, cable length ratio and frequency ratio on $1^{st}$ mode frequency and mode shape are addressed.

• 한국구조물진단유지관리공학회 논문집
• /
• 제18권3호
• /
• pp.10-19
• /
• 2014

파형강판은 제형, 정현형 등의 형상으로 얇은 강판을 주름지게 가공한 것으로 두꺼운 평판을 대신하여 사용하여도 높은 면외방향의 강성을 확보할 수 있다. 또한, 아코디언효과로 축방향 강성이 거의 없어 플레이트거더의 웨브에 적용할 경우 웨브가 전단력만을 부담하는 방법으로 쉽게 설계할 수 있다. 그러나 파형강판의 전단좌굴은 평판과는 달리 국부좌굴과 전체좌굴 외에도 이들의 연성에 의해서도 좌굴이 발생하는 매우 복잡한 특성이 있으며, 이러한 연성좌굴에 대한 원인과 특성의 규명은 정현형의 경우 제형보다 연구결과가 부족한 실정이다. 따라서 본 연구에서는 정현형 파형강판의 전단좌굴 특성과 연성좌굴이 발생하는 경향에 대해서 연구하였다. 전단좌굴강도를 계산하기 위해서는 유한요소프로그램을 이용하였고 해석결과를 정해와 비교하였다. 또한, 주름의 두께와 형상 파라메타에 따른 좌굴응력 변화의 특성과 좌굴모드형상의 변화를 분석하였으며, 이들의 결과를 이론식의 결과와 비교하여 좌굴양상의 변화시점에 대해서 분석하였다.

• Structural Engineering and Mechanics
• /
• 제7권1호
• /
• pp.81-94
• /
• 1999

The dynamic analysis of trusses using the finite element method tends to overlook the effect of local member dynamic behavior on the overall response of the complete structure. This is due to the fact that the lateral inertias of the members are omitted from the global inertia terms in the structure mass matrix. In this paper a condensed dynamic stiffness matrix is formulated and used to calculate the exact dynamic properties of trusses without the need to increase the model size. In the examples the limitations of current solutions are presented together with the exact results obtained from the proposed method.

• Advances in nano research
• /
• 제4권4호
• /
• pp.265-279
• /
• 2016

Present study interests with the longitudinal forced vibration of nanorods. The nonlocal elasticity theory of Eringen is used in modeling of nanorods. Uniform, linear and sinusoidal axial loads are considered. Dynamic displacements are obtained for nanorods with different geometrical properties, boundary conditions and nonlocal parameters. The nonlocal effect increases dynamic displacement and frequency when compared with local elasticity theory. Present results can be useful for modeling of the axial nanomotors and nanoelectromechanical systems.

• 한국강구조학회 논문집
• /
• 제11권4호통권41호
• /
• pp.351-362
• /
• 1999

용접 및 볼트 연결부 균열이 사장교 케이블 정착부의 동특성에 미치는 영향을 파악하여, 국부적으로 취약한 케이블 정착부의 손상을 현장에서 쉽게 탐지할 수 있는 가능성을 제시하였다. 해석대상 구조물로서 현재 서해안고속도로의 일부로 시공되고 있는 서해대교 케이블 정착부를 선택하였다. 케이블과 정착부의 연결판을 케이블요소 및 쉘요소로 함께 모델링하여 자유진동해석을 수행하였다. 해석결과 케이블 정착단에서 용접부 균열이 발생한 경우, 연결판의 고유진동수가 균열이 발생하지 않은 경우에 비하여 최대 16%정도 작아짐을 확인하였다. 따라서, 연결판의 고유진동수를 측정하여 케이블 정착부의 손상을 충분히 파악할 수 있다고 판단된다.

• 한국공간구조학회논문집
• /
• 제21권4호
• /
• pp.57-64
• /
• 2021

This paper conducted a comparative analysis of the shear buckling characteristics of trapezoidal and sinusoidal corrugated steel plates considering of their initial imperfection. Initial imperfection refers to the state where the shape of the corrugated plate is initially not perfect. As such, an initially imperfect shape was assumed using the eigen buckling mode. To calculate the buckling stress of corrugated steel plates, the linear buckling analysis used a boundary condition which was applied to the plate buckling analysis. For the comparison of trapezoidal and sinusoidal corrugation, the shape parameters were assumed using the case where the length and slope of each corrugation were the same, and the initial imperfection was considered to be from 0.1% to 5% based on the length of the steel plate. Here, for the buckling analysis, ANSYS, a commercial FEA program, was used. From the results of buckling analysis, the effect of overall initial imperfection showed that the larger the initial imperfection, the lower the buckling stress. However, in the very thin model, interaction or local buckling was dominant in the perfect shape, and in this case, the buckling stress did not decrease. Besides, the sinusoidal model showed higher buckling stress than the trapezoidal one, and the two corrugation shapes decreased in a similar way.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 추계학술대회논문집
• /
• pp.1302-1306
• /
• 2007

Joints are used extensively in various industries. For instance, structural adhesives are used in place of the traditional mechanical fasteners, such as screws and bolts, because they are much lighter and spread the stresses more uniformly across the joints. For efficient designs of joints, knowledge of static and dynamic characteristics of joints is essential. Most analysis of joints are carried out using analytical equations or finite element method. In this paper, the characteristics of four conditions of lap-joint beam are investigated experimentally. The mode shapes and nodal points of beam show that there are different deformations in each condition. These deformations may cause high stresses and may initiate local cracking and delamination failures.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2006년도 추계학술대회 논문집
• /
• pp.954-963
• /
• 2006

PRT(Personal Rapid Transit) is alternation mode of auto and advanced transportation system as future transportation mode cope with the situation caused by increasing traffic demand, vehicle, environment, energy problem. but there is no place where PRT is operated therefore it is necessary of study on application of PRT The purpose of this study is putting into shape of fundamental notion and role of PRT as transit system and studying of domestic application possibility We expect that PRT make transit will make variety and be able to connect with mass transportation facility, have a connection between trunk line and branch line, be a effective local transportation system within CBD, be a transportation system within leisure complex. This study focus on connection with mass transportation facility in the middle of 5 type, we class as. and we investigate application of PRT by process of making a choice applicable case area

• Geomechanics and Engineering
• /
• 제29권2호
• /
• pp.193-205
• /
• 2022

The face stability of shield tunnelling is the most important control index for safety risk management. Based on the reliability of the transparent clay (TC) model test, a series of TC model tests under different buried depth were conducted to investigate the progressive failure mechanism of tunnel face. The support pressure was divided into the rapid descent stage, the slow descent stage and the basically stable stage with company of the local failure and integral failure in the internal of the soil during the failure process. The relationship between the support pressure and the soil movement characteristics of each failure stage was defined. The failure occurred from the soil in front of the tunnel face and propagated as the slip zone and the loose zone. The fitted formulas were proposed for the calculation of the failure process. The failure mode in clay was specified as the basin shape with an inverted trapezoid shape for shallow buried and appeared as the basin shape with a teardrop-like shape in deep case. The implications of these findings could help in the safety risk management of the underground construction.