• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.10a
• /
• pp.167-172
• /
• 2002

Nonlinear analysis of the reinforced concrete beam subjected to torsion is presented. Seventeen equations involving seventeen variables are derived from the equilibrium equation, compatibility equation, and the material constitutive laws to solve the torsion problem. Newton method was used to solve the nonlinear simultaneous equations and efficient algorithms are proposed. Present model covers the behavior of reinforced concrete beam under pure torsion from service load range to ultimate stage. Tensile resistance of concrete after cracking is appropriately considered. The softened concrete truss model and the average stress-strain relations of concrete and steel are used. To verify the validity of Present model, the nominal torsional moment strengths according to ACI-99 code and the ultimate torsional moment by present model are compared to experimental torsional strengths of 55 test specimens found in literature. The ultimate torsional moment strengths by the present model show good results.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.554-559
• /
• 2007

The cylinder cover stud for assembling the combustion chamber components of low-speed marine diesel engine is one of the main structural components in engine. To understand the structural behavior of the stud is quite important for safe and economic design of it. In this paper, the structural behavior and design adequacy of the stud have been evaluated through strain measurement and structural analysis for the world's two largest engine types. Moreover, a feasibility study for design modification was carried out based on fatigue test and calculation. The results showed that 1) the stud experiences very high stress ratio under normal operating conditions, 2) the fatigue strength of the stud is sufficient, and 3) results from strain measurement and structural analysis were quite close each other.

• Journal of Welding and Joining
• /
• v.10 no.1
• /
• pp.35-42
• /
• 1992

In this study, the stress concentration phenomenon for the dissimilar joints(ceramic-metal) bonded by thermal treating using a soft-insert metal(copper) was investigated with the aid of FEM(finite element method) under the load condition of uniform tension. The analysis was carried out by the supposing that stress states are plane stress or plane strain and elastic or elastic-plastic. And the Von Mises yield criterion and the incremental theory as plastic flow were adopted in this analysis. As the summarized results obtained, the stress concentration phenomenon was severer as the soft insert metal was thicker, in plane strain than in plane stress and in elastic-plastic state than in elastic state. Furthermore, the inducing mechanism of stress concentration was well expressed by the constraint forces(Fc) generated between the soft and the hard material.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.5
• /
• pp.1407-1416
• /
• 1991

본 연구에서는 Liu의 수식화를 바탕으로 가공 경화성을 고려하여 수식화를 재 구성하고, 유한요소 프로그램을 개발하여 평면 변형 인발문제를 극한 해석함으로써, 성형에 필요한 한계 하중 및 최적 속도장을 직접적으로 구하였다.수렴되어진 최적 속도장으로 각 요송에서의 변형률 속도, 변형률 및 격자 변형등을 수치적으로 계산함 으로써 가공에 따른 변형 특성도 파악하였다. 한계 하중은 항공기 구조용 소재인 알 루미늄 6061 재료를 이용하여 판재 인발 실험을 행함으로써 얻은 결과치와 비교 검토 하였으며, 유동 특성을 관찰하기 위하여 격자 왜곡(grid distortion) 실험을 하여 얻 은 변형 패턴과 수치 계산에서 구한 격자변형 패턴을 상호 비교하였다.

• Computers and Concrete
• /
• v.7 no.5
• /
• pp.437-453
• /
• 2010

CFRP has been widely used for strengthening reinforced concrete members in last decade. The strain transfer mechanism from concrete face to CFRP is a key factor for rigidity, ductility, energy dissipation and failure modes of concrete members. For these reasons, determination of the effective CFRP bonding length is the most crucial step to achieve effective and economical strengthening. In this paper, generalizations are made on effective bonding length by increasing the amount of test data. For this purpose, ANSYS software is employed, and an experimentally verified nonlinear finite element model is prepared. Special contact elements are utilized along the concrete-CFRP strip interface for investigating stress distribution, load-displacement behavior, and effective bonding length. Then results are compared with the experimental results. The finite element model found consistent results with the experimental findings.

• Steel and Composite Structures
• /
• v.29 no.2
• /
• pp.161-173
• /
• 2018

Point bending is often used for cambering and curving structural steel girders. An analytical solution, applicable in the elasto-plastic range only, that relates applied loads to the desired curve was recently developed for inducing horizontal curves using four-point bending. This solution does not account for initial residual stresses and geometric imperfections built-in hot-rolled sections. This paper presents results from a full-scale test on a hot-rolled steel section curved using four-point bending. In parallel, a numerical analysis, accounting for both initial geometric imperfections and initial residual stresses, was carried out. The models were validated against the experimental results and a good agreement for lateral offset and for strain in the elasto-plastic and post-plastic ranges was achieved. The results show that the effect of initial residual stresses on deformation and strain is minimal. Finally, residual stresses due to cold bending calculated from the numerical analysis were assessed and a revised stress value for the service load design of the curved girder is proposed.

• Transactions of Materials Processing
• /
• v.6 no.3
• /
• pp.203-212
• /
• 1997

In this research, to obtain the optimal die width of CV die(conventional die), which replaces FM die in free forging of large scale rotor using the flat die, the model material experiments and theoretical analysis using three dimensional FEM are performed. The FM die, which was designed to remove Mannesmann's effect at the central part of the ingot, has very bad workabiltity in real field, therefore on the empirical base they use the CV die of wide width in actual working field. In this study, the excellency of CV die is proved quantitively, and the optimal die width of CV die is determined through the model material experiments and theoretical analysis using FEM in the point of effective strain, stresses, and load.

• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.286-291
• /
• 2000

The finite element analyses of mechanical rubber components are executed to predict the behavior of deformation and stress distribution in destgn step. The non-linear properties of rubber which are described as strain energy functions are important parameters to design and evaluate rubber components. These are determined by material tests which are tension, compression and shear test. The behaviors of loads-displacements of rubber components such as a roll tubber spring and resilient ring and additional spring for railway suspension system are evaluated by using commercial FEA code. It is shown that the results by FEA simulations are in close agreement with the test results.

• 연구논문집
• /
• s.26
• /
• pp.33-42
• /
• 1996

The transmission system of a washing machine which is called by the clutch is one of the most important components to preserve the performance. The clutch housing has a role to guard and mount the transmission system on the frame of the machine. The load which is applied on the clutch housing depends on the operating conditions. Nowadays the dehydration speed is higher and higher in order to improve the efficiency. In this study, the strains on the predicted weak positions were measured using the strain gage and its measuring equipment. The relationships between the dehydration speeds and the maximum principal strains were obtained. Finite element analysis is executed to acquire the effect of the dehydration speed on the stress of the clutch housing. The distributions of the equivalent stress and the maximum stresses under the various speeds, the various loading directions and the various thickness of the clutch housing were obtained.

• Transactions of Materials Processing
• /
• v.9 no.1
• /
• pp.59-65
• /
• 2000

Most studies of failure analysis in ductile metals have been based on the classical plasticity theory using the local constitutive relations. These frequently yields a physically unrealistic solution, in which a numerical prediction of the onset of a deformation localization shows an inherent mesh-size sensitivity. A one way to remedy the spurious mesh sensitivity resulted in the unreasonable results is to incorporate the non-local plasticity into the simulation model, which introduce an internal (material) length-scale parameter into the classical constitutive relations. In this paper, a non-local version of the modified Gurson constitutive relation has been introduced into the finite element formulation of the simulation for plane strain compression of the visco elastic-plastic void material. By introducing the non-local constitutive relations we could successfully removed the inherent mesh-size sensitivity for the prediction of the deformation localization. The effects of non-local constitutive relation are discussed in terms of the load-stroke curve and the strain distributions accross the shear band.