• Proceedings of the KIEE Conference
• /
• 1994.11a
• /
• pp.15-17
• /
• 1994

The economic operation in power systems has long been in keen interests for power system engineers. The classical equal incremental fuel cost rule is still the basis for it, even though more elaborate tools such as optimal power flow have been developed already. The classical method requires usually many iterations, while the optimal power flow shows often some difficulties. This paper suggests a single step solution based on the classical method revisited. The concept is shown graphically. Three sample systems are compared. The proposed approach has shown a single step solution regardless system sizes, while the conventional methods require many iterations.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.10
• /
• pp.1103-1109
• /
• 2013

This paper presents an optimal capacity design of a Hybrid generation system based on economical evaluation for various loads. Optimal sizes of a standalone and grid connection wind- PV hybrid systems were designed for normal, residential and industrial loads using HOMER (Hybrid Optimization Model for Electronic Renewable). Their economical evaluation were performed and compared with a diesel generation system that covers the same loads. The results showed that the stand alone hybrid generation system can be more economical than a diesel generation system for long term operation.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.3
• /
• pp.139-146
• /
• 2004

In this study, to achieve the optimal conditions for mechanical hyper-fine pattern fabrication process, deformation behavior of the materials during indentation scratch test was studied with numerical method by ABAQUS S/W. Brittle materials (Si, Pyrex glass 7740) were used as specimens, and forming conditions to reduce the elastic recovery and pile-up were proposed. The indenter was modeled as a rigid surface. Minimum mesh sizes of specimens are 1-l0nm. Variables of the nanoindentation scratch test analysis are scratching speed, scratching load, tip radius and tip geometry. The nano-indentation scratch tests were performed by using the Berkovich pyramidal diamond indenter. Comparison between the experimental data and numerical result demonstrated that the FEM approach can be a good model of the nanoindentation scratch test. The result of the investigation will be applied to the fabrication of the hyper-fine pattern.

• Ocean Systems Engineering
• /
• v.2 no.4
• /
• pp.289-295
• /
• 2012

Assume fluid eddy viscosity in the vertical direction is parabolic. Sediment particles diffuse with the given fluid eddy viscosity. However, when the vertical diffusion coefficient profile is computed from the suspended sediment concentration profile, the coefficient shows lager values than the fluid mixing coefficient values. This trend was explained by using two sizes of sediment particles. When fine sediment particles like wash load are added in water column the sediment mixing coefficient looks much larger than the fluid mixing coefficient.

• Smart Structures and Systems
• /
• v.23 no.4
• /
• pp.373-385
• /
• 2019

A study concerning the strength of brittle materials is presented in this paper. The failure behavior was investigated examining the plane of the crack after the failure and comparing the results obtained with those deriving from the fracture mechanics theory. Although the proposed methods are valid in general for brittle materials, the experiment was performed on glass because the results are more significant for this. Glass elements of various sizes and different edge finishes were subjected to bending tests until collapsing. The bending results were studied in terms of failure load and energy dissipation, and the fracture surfaces were examined by means of microscopic analysis, in which the depth of the flaw and the mirror radius of the fracture were measured and the strength was calculated. These results agreed with those obtained from the fracture mechanics analysis.

• Journal of Ceramic Processing Research
• /
• v.19 no.5
• /
• pp.419-423
• /
• 2018

A newly conceived geopolymer composite was fabricated by a combination of the geopolymer and polyurethane sponge. The density and porosity of hardened geopolymer composite, corresponded to different pore sizes of polyurethane sponge, exhibited no significant differences from each other. However, the mechanical behavior, the compressive strength and flexural strength, showed slight differences accordingly. Fracture of the geopolymer composite exposed to high compressive load was not observed from all specimens containing polyurethane sponge. The toughness enhancement of the geopolymer composite, due to spontaneous elasticity of polyurethane sponge, crack spread, and crack diffraction, was identified through the stress-strain curve and microstructure of fracture surface. The newly designed geopolymer composite having a 3-dimensional sponge skeleton showed relatively higher flexural strength of 8.0 MPa than other conventional geopolymer composites.

• Geomechanics and Engineering
• /
• v.24 no.3
• /
• pp.227-235
• /
• 2021

A criterion and a method for solving a problem on the prevention of mine working fracture under the action of tectonic and gravitational forces are offered. Based on minimal criterion, theoretical analysis of the definition of the optimal shape of working in the rock mass weakened by arbitrarily located rectilinear cracks was carried out. A closed system of algebraic equations allowing to minimize the stress state and stress intensity factors depending on mechanical and geometrical characteristics of the rock, is constructed. The relation between the shape of the working and the stress intensity factors and also location and sizes of the cracks is obtained. The found optimal shape of working increases load-bearing capacity of the rock.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.8 no.2
• /
• pp.1-5
• /
• 2002

In order to improve the load efficiency of pallets and trucks for agricultural products, various transport package sizes have been analyzed by modular coordination process. From the results, the load efficiency on pallet was 99.8 percent when size was 550 by 366 mm and 366 by 275 mm. Load efficiency of standard pallet(1100 by 1100mm) was 93.6% for truck with 11 tons load capacity while as low as 41.1% for 2.5 ton trucks. Like any other products, this study proved that trucks with more than 8 tons of capacity were highly recommended for transportation of agricultural products.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.22 no.1
• /
• pp.81-88
• /
• 2009

This paper alined at the development of a lateral drift control method that is able to quantitatively control the lateral drift of global node. For this, we applied an efficient partial reanalysis algorithm. By using this algorithm, we could recalculate the displacement and member force of the specific node without reanalyzing the entire structure when member stiffness changes partially. The theoretical concepts of the algorithm are so simple that it is not necessary to solve the complicate differential equation or to repeat the analysis of entire structure. The proposed method calculates the drift contribution of each member for the global displacement according to the variation of section sizes by using the algorithm. Then by changing the member sizes as the order of drift contribution, we could control the lateral drift of global node with a minimum quantity of materials. 20 story braced frame structure system is presented to illustrate the usefulness of proposed method. It is shown that the proposed method is very effective in lateral drift control and the results obtained by proposed method are consistent with those of commercial analysis program.

• The korean journal of orthodontics
• /
• v.22 no.3 s.38
• /
• pp.557-578
• /
• 1992

Heat treatment which removes internal stress enhances the mechanical properties of the orthodontic arch wire. The main purpose of this experiment was to investigate the effects of the heat treatment on the mechanical properties of the Elgiloy wire. The Elfiloy wire, 0.016' X 0.022' and 0.018' X 0.025', were heat treated in an electric oven for 5, 10 and 15 minutes at selected temperatures between 300 and $900^{\circ}C$. Tensile strength and load deflection rate were measured to reveal the changes of mechanical property at various conditions, and each specimen was observed under metallurgic microscope. Also to trace the precipitation material due to overheat treatment, a qualitative analysis was carried out with EDS system. It was found that heat treatment at a low temperature caused an increase in the tensile strength and bending resistance, and a maintenance in the fibrous in the tensile strength and bending resistance, and a maintenance in the fibrous structure of both sizes of wire. The changes observed in properties and appearance were probably due to the relief of internal stresses incurred in the metal during cold working. In both sizes of wire the tensile strength and the bending resistance continued to decrease at high temperature, and the fibrous structure continued to disappear then was not observed at $900^{\circ}C$. The carbide precipitation founded in grain boundary at $750^{\circ}C$ probably was other elements carbide (Ni, Co) except Cr. The grain growth was observed at $1100^{\circ}C$. Optimum heat treatment for the 0.016' X 0.022' Elgiloy wire was 10 minutes at $500^{\circ}C$, and for the 0.018' X 0.025' Elgiloy wire it was 5 to 15 minutes at $500^{\circ}C$.