• Proceedings of the KIEE Conference
• /
• 2002.06a
• /
• pp.135-141
• /
• 2002

This paper presents an implementation of high-dynamic performance of position sensorless motion control system of Reluctance Synchronous Motor(RSM) drives for an industrial servo system with direct torque control(DTC), The problems of DTC for high-dynamic performance and maximum efficiency RSM drive due to a saturated stator linkage flux and nonlinear inductance curve with various load currents, The accurate estimation of the stator flux and torque are obtained using stator flux observer of which a saturated inductance Ld and Lq can be compensated by adapting from measurable the modulus and angle of the stator current space vector. To obtain fast torque response and maximum torque/current with varying load current, the reference command flux is ensured by imposing Ids=Iqs. This control strategy is proposed to fast response and optimal efficiency for RSM drive. In order to prove rightness of the suggested control algorithm, the actual experiment carried out at ${\pm}$20 and ${\pm}$1500 rpm. The developed digitally high-performance control system are shown some good response characteristic of control results and high performance features using 1.0kW RSM of which has 2.57 Ld/Lq salient ratio.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.1
• /
• pp.58-66
• /
• 2009

In this paper, vector control to applied disturbance offset feedforward loop control for changing disturbances with various mechanical parameter is suggested. The proposed system estimate load torque based on induction motor torque using minimum diemension state observer. Because speed controller using state observer is used on condition of feedforward loop fur a torque, the robust speed control system realized. In this study, the proposed paper does to heighten reliability of system by presuming and use the speed by voltage and current that is detected without speed sensor. To prove the propriety of this paper, the various simulation carried out adequacy using a Matlab Simulink, and at the same time real system is made, using a ADMC300 digital signal processor, so it is proved. As the experimental result of embodying the system, the robust system is realized.

• Proceedings of the KIEE Conference
• /
• 2000.07b
• /
• pp.669-671
• /
• 2000

This paper introduced the scheme that it improved performance of magnetic levitation system with zero power controller. Magnetic levitation is used widely, but it is complicated and difficult to control due to having nonlinear characteristics of gap and current. So, it is proposed a scheme considered changed gap according to variable load and is verified by simulation and experiments in this paper.

• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.591-593
• /
• 1996

In order to implement the direct vector control type sensorless vector control, the rotor flux and the angular speed of the rotor can only be estimated through the measurement of the stationary voltage and current states. To estimate the rotor flux, the use of the rotor flux observer(RFO) has been proposed. It is known that the RFO is relatively insensitive to parameter variations. Using the rotor flux value obtained from the RFO, the rotor flux vector can be estimated. The angular speed of the rotor is estimated by the difference between the synchronous angular speed and the slip angular speed, both of which are derived from the rotor flux vector. However unwanted high order frequency waves become incorporated into the synchronous angular speed during calculations. Thus we propose the use of digital filters that will eliminate these high frequency waves. We have demonstrated through computer simulations that the use of filters results in stable system activity over a wide speed range and good response to load variations.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.7 no.5
• /
• pp.427-436
• /
• 2002

This paper presents an implementation of high-dynamic performance of position sensorless motion control system of Reluctance Synchronous Motor(RSM) drives for an industrial servo system with direct torque control(DTC). The problems of high-dynamic performance and maximum efficiency RSM drives controlled by DTC are saturation of stator linkage flux and nonlinear inductance characteristics with various load currents. The accurate estimation of the stator flux and torque are obtained using stator flux observer of which a saturated inductance $L_d$ and $L_q$ can be compensated by adapting from measurable the modulus of the stator current and rotor position. To obtain fast torque response and maximum torque/current with varying load current, the reference command flux is ensured by imposing $I_{ds} = I_{qs}$. This control strategy is proposed to achieve fast response and optimal efficiency for RSM drive. In order to prove rightness of the suggested control algorithm, the actual experiment carried out at $\pm$20 and $\pm$1500 rpm. The developed digitally high-performance motion control system shown good response characteristic of control results and high performance features using 1.0kW RSM which has 2.57 Ld/Lq salient ratio.

• Proceedings of the KIEE Conference
• /
• 1988.11a
• /
• pp.414-417
• /
• 1988

This paper presents a study on the operation of a digitally controlled DC servo motor drive at low speed region. Two schemes aiming to improve the transient behavior of the speed control system are considered. The first scheme is the current positive feedback scheme to reduce the sensitivity of the system with respect to the load torque variations. The second one is the speed observer based on a motor model. Finally, the two schemes are studied by simulation and then verified experimetally using a prototype DC motor drive.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.8
• /
• pp.1405-1411
• /
• 2007

In this paper, a new speed sensorless control based on a fuzzy compensator are proposed for the interior permanent magnet synchronous motor (IPMSM) drives. The conventional proportional plus integrate(PI) control are very sensitive to step change of the command speed, parameter variations and load disturbance. To cope with these problems of the PI control, the estimated speeds are compensated by using the fuzzy logic controller (FLC). In the FLC used by the speed compensator of the IPMSM, the system control parameters are adjusted by the fuzzy rule based system, which is a logical model of the human behavior for process control. The effectiveness of algorithm is confirmed by the experiments.

• Journal of Electrical Engineering and information Science
• /
• v.1 no.2
• /
• pp.58-66
• /
• 1996

An adaptive input-output linearization technique of an interior permanent magnet synchronous motor with a specified output dynamic performance is proposed. The adaptive parameter estimation is achieved by a model reference adaptive technique where the stator resistance and the magnitude of flux linkage can be estimated with the current dynamic model and state observer. Using these estimated parameters, the linearizing control inputs are calculated. With these control inputs, the input-output linearization is performed and the load torque is estimated. The adaptation laws are derived by the Popov's hyperstability theory and the positivity concept. The robustness and the output dynamic performance of the proposed control scheme are verified through the computer simulations.

• Proceedings of the KIEE Conference
• /
• 1995.07a
• /
• pp.334-336
• /
• 1995

An adaptive feedback linearization technique of a PM synchronous motor with specified output dynamic performance is proposed. The adaptive parameter estimation is achieved by a model reference adaptive technique where the stator resistance and flux linkage can be estimated with the current dynamic model and the state observer. Using these estimated parameters, the linearizing control inputs are calculated and a nonlinear coupled model of a PM synchronous motor is input-output linearized. The resultant model has the load torque disturbance. To get ti perfect decoupled model, the load torque is estimated. The adaptation laws are derived by the hyperstability theory and positivity concept. The robustness of the proposed control scheme will be proven through the computer simulations.

• Korean Journal of Transplantation
• /
• v.31 no.4
• /
• pp.170-176
• /
• 2017

We need to establish an informative guideline to increase inter-institutional and inter-observer reproducibility of renal transplant diagnosis, and to improve the diagnostic ability of pathologists in Korea. A first nation-wide survey for renal transplant pathology was conducted by Renal Pathology Study Group of the Korean Society of Pathologists in 2016, to provide the continued excellence in the transplantation pathology laboratory, and to improve the diagnostic ability for the best treatment of transplant patients. This survey revealed the significant variations in scale, work load and biopsy indications for the renal transplant pathology in various institutions in Korea. The Banff classification were used by all institutions for the diagnosis of renal transplant pathology, but different formats were used: most institutions (70%) used the "2013 Banff classification" while the others were using "2007 Banff classification" (20%) or even older formats. In daily diagnostic practice of the renal allografts, difficulties that pathologists encounter were quite diverse due to different environments they work in. Most respondents agreed that standardized diagnostic practice guidelines, regular education on renal transplant pathology and convenient ways of consultation are further needed. We are currently working toward the enhancement of the expertise of renal pathologists and to increase inter-institutional and inter-observer reproducibility by 1) development of a set of virtual slides of renal allograft biopsies for the training, 2) validation and gathering expert's consensus on the core variables of rejection diagnosis by using virtual slides, and 3) continued education by the developed virtual slide atlas.