• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2013.10a
• /
• pp.361-364
• /
• 2013

Since the non-overlapping gate driver used in conventional DC-DC boost converters generates fixed dead-times, the converters suffer from the body-diode conduction loss or the charge-sharing loss. A adaptive control method has been proposed to reduce these loses. In this method, however, occurrence of and overlapping time of two power transistors in CCM results in reduction of efficiency. In this paper, to overcome this problem a new adaptive control method in proposed, and a DC-DC boost converter with the proposed adaptive control and power switching has been designed in a 0.35um CMOS process. The designed converter outputs 3.3V from a input voltage of 2.5V. The switching frequency is 500kHz and the maximum power efficiency is 95.3% at a load current 150mA. The designed chip area is $1720um{\times}1280um$.

• Journal of Power Electronics
• /
• v.11 no.6
• /
• pp.880-889
• /
• 2011

In this paper, a novel Active Voltage Quality Regulator (AVQR) topology with a thyristor rectifier and an adaptive dclink voltage control strategy are proposed. The proposed AVQR can efficiently mitigate the long duration variations (e.g. undervoltages/overvoltages), voltage imbalances and voltage harmonics. Compared with conventional AVQRs, it can regulate the load voltage very well with a much lower dc-link voltage. This is accomplished by replacing the diode rectifier with a thyristor rectifier. Moreover, its dc-link voltage can vary with the deviations of the supply voltage through the proposed adaptive dc-link voltage control strategy. All of these contribute to its significantly higher efficiency for online operating, which is very important and attractive for many applications. The proposed topology and control strategy are theoretically analyzed in detail. Simulation results are also provided in the paper. Finally, the feasibility and effectiveness of the proposed method are verified by means of experimental results from a 2kVA prototype. Both of the simulation and experimental results show that the proposed AVQR can achieve a much higher efficiency and similar regulation performance when compared with the conventional ones.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.3A
• /
• pp.267-277
• /
• 2011

Like other wireless network protocols, IEEE 802.15.4 adopts CA (Collision Avoidance)algorithm to avoid the early collision of a new packet by randomizing its first transmission time rather than its immediate delivery. The traditional CA scheme of IEEE 802.15.4, however, selects the random access time from the predetermined range without considering the degree of current congestion. It probably causes either a long delay to settle in the suitable range for the current network load or frequent clashes especially during the long lasting heavy traffic period. This paper proposes an ACA(Adaptive Collision Avoidance) algorithm adapting the initial backoff range to the undergoing collision variations. It also introduces a mathematical model to predict the performance of ACA algorithm added to IEEE 802.15.4. With only small deviations from corresponding simulations, our analytical model shows that ACA technique can improve the throughput of IEEE 802.15.4 by up-to 41% maximally in addition to shortening the packet delays.

• The KIPS Transactions:PartC
• /
• v.15C no.1
• /
• pp.19-30
• /
• 2008

Sensor nodes are used as a storage space in the data centric storage method for sensor networks. Sensor nodes save the data to the node which is computed by hash table and users also access to the node to get the data by using hash table. One of the problems which the data centric storage method has is that queries from many users who are interested in the popular data could be concentrated to one node. In this case, responses for queries could be delayed and the energy of heavy loaded node could be dissipated fast. This would lead to reduction of network life time. In this paper, ALT, Data Centric Storage based on Adaptive Local Trajectory, is proposed as scalable data centric storage method for sensor network. ALT constructs trajectory around the storage node. The scope of trajectory is increased or decreased based on the query frequency. ALT distributes the query processing loads to several nodes so that delay of response is reduced and energy dissipation is also distributed.

• The KIPS Transactions:PartC
• /
• v.9C no.5
• /
• pp.783-788
• /
• 2002

Adaptive Cyclic Packet Dropping algorithm (ACPD), and Non-adaptive Cyclic Packet Dropping algorithm (NCPD) are applying stricter drop precedence than that of RIO algorithm. Especially, the ACPD algorithm drops adaptively packets for the congestion control, as predicting traffic pattern between each cycle. Therefore the ACPD algorithm makes up for the drawback of RIO algorithm and minimizes the wastes of the bandwidth being capable of predicting in the NCPD algorithm. And we executed a simulation and analyzed the throughput and packet drop rate based on Sending Priority changing dynamically depending on network traffic. In this algorithm, applying strict drop precedence policy, we get better performance on priority levels. The results show that the proposed algorithms may provide more efficient and stricter drop precedence policy as compared to RIO independent of traffic load. The ACPD algorithm can provide better performance on priority levels and keep stricter drop policy than RIO and the NCPD algorithm.

• Journal of Electrical Engineering and Technology
• /
• v.2 no.4
• /
• pp.543-548
• /
• 2007

We present a dynamic Bayesian network (DBN) model of a generalized class of nonstationary birth-death processes. The model includes birth and death rate parameters that are randomly selected from a known discrete set of values. We present an on-line algorithm to obtain optimal estimates of the parameters. We provide a simulation of real-time characterization of load traffic estimation using our DBN approach.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1998.10a
• /
• pp.54-59
• /
• 1998

In order to minimize straightness error of deflected shafts, a automatically bending process control system is designed, fabricated, and studied. The multi-step straightening process and the three-point bending process are developed for the geometric adaptive straightness control. Load-deflection relationship, on-line identification of variations of material properties, on-line springback prediction, and studied for the three-point bending processes. Selection of a loading point supporting condition are derved form fuzzy inference and fuzzy self-learning method in the multi-step straighternign process. Automatic straightening machine is fabricated by using the develped ideas. Validity of the proposed system si verified through experiments.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 1997.06a
• /
• pp.49-54
• /
• 1997

For the purpose of a flexible coded video transmission over a heterogeneous network, we propose a new packetization method for coded video data. The proposed method achieves small degradation of coded picture quality in case of packet discard at the network node and does not require heavy processing load for bitrate control operation. Computer simulation results show that the bitrate reduction from 384 kb/s to 192 kb/s does not cause severe degradation in picture quality.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2001.10a
• /
• pp.341-344
• /
• 2001

We propose a novel method to simplify the computational load of ILSP algorithm for CDMA environment. Since this method processes the block matrix by a vector sequentially, the complex matrix computation ran be avoided. The performance of the algorithm is verified by computer simulations.

• Proceedings of the KIEE Conference
• /
• 1995.07a
• /
• pp.388-390
• /
• 1995

A new control scheme based on dead beat control with adaptive parameter estimation for PWM Inverter is proposed. The proposed scheme updates dead beat control parameters continouously, and make PWM inverter excellent performance at any load or parameter condition. Simulation results show very attractive features in this proposed scheme.