• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.04b
• /
• pp.7-7
• /
• 2009

Lead telluride (PbTe) is a very promising thermoelectric material due to its narrow band gap (0.31 eV at 300 K), face-centered cubic structure and large average excitonic Bohr radius (46 nm) allowing for strong quantum confinement within a large range of size. In this work, we present the thermoelectric properties of individual single-crystalline PbTe nanowires grown by a vapor transport method. A combination of electron beam lithography and a lift-off process was utilized to fabricate inner micron-scaled Cr (5 nm)/Au (130 nm) electrodes of Rn (resistance of a near electrode), Rf (resistance of a far electrode) and a microheater connecting a PbTe nanowire on the grid of points. A plasma etching system was used to remove an oxide layer from the outer surface of the nanowires before the deposition of inner electrodes. The carrier concentration of the nanowire was estimated to be as high as $3.5{\times}10^{19}\;cm^{-3}$. The Seebeck coefficient of an individual PbTe nanowire with a radius of 68 nm was measured to be $S=-72{\mu}V/K$ at room temperature, which is about three times that of bulk PbTe at the same carrier concentration. Our results suggest that PbTe nanowires can be used for high-efficiency thermoelectric devices.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.2
• /
• pp.173-178
• /
• 2012

Currently, active research is being performed on printing of electronic devices such as RFID devices, flexible displays, solar cells, and e-paper. This technique has several advantages over existing technologies such as lithography and etching. In particular, RFID devices, flexible displays, solar cells, and e-paper require flexibility and a mass production system. Thus, attention is being focused on the roll-to-roll process. High quality should be guaranteed in the roll-to-roll printed electronics systems, and good thickness and roughness qualities must be ensured. Experimental design was applied to this problem to analyze the main effects and interaction effects of various factors. Matching technology between the nip roll characteristics and the quality of the print pattern in roll-to-roll printed electronics systems was proposed to improve the printing quality.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.165-165
• /
• 2014

In this study, we demonstrated that the soft lithographic patterning processing of chemical vapor deposition (CVD) graphene and rGO sheets as large scale, low cost, high quality and simplicity for future industrial applications. Recently, a previous study has reported that single layer graphene grown via CVD was patterned and transferred to a target surface by controlling the surface energy of the polydimethylsiloxane (PDMS) stamp [1]. Using this approach, the surface of a relief-patterned elastomeric stamp was functionalized with hydrophilic dimethylsulfoxide (DMSO) molecules to enhance the surface energy of the stamp and to remove the graphene-based layer from the initial substrate and transfer it to a target surface [2]. Further, we developed a soft lithographic patterning process via surface energy modification for advanced graphene-based flexible devices such as transistors or simple and efficient chemical sensor consisting of reduced graphene oxide (rGO) and a metallic nanoparticle composite. A flexible graphene-based device on a biocompatible silk fibroin substrate, which is attachable to an arbitrary target surface, was also successfully fabricated.

• Journal of the Korean Vacuum Society
• /
• v.16 no.5
• /
• pp.366-370
• /
• 2007

Nano-scopic holes which are distributed densely and uniformly were fabricated on $SiO_2$ surface. Self-assembling resists were used to produce a layer of uniformly distributed parallel poly methyl methacrylate (PMMA) cylinders in a polystyrene (PS) matrix. The PMMA cylinders were degraded and removed by acetic acid rinsing. Subsequently, PS nanotemplates were fabricated. The patterned holes of PS template were approximately $8{\sim}30\;nm$ wide, 40 nm deep, and 60 nm apart. The porous PS template was used as a dry etching mask to transfer the pattern of PS template into the silicon oxide thin film during reactive ion etching (RIE) process. The sizes of the patterned holes on $SiO_2$ layer were $9{\sim}33\;nm$. After pattern transfer by RIE, uniformly distributed holes of which size were in the range of $6{\sim}22\;nm$ were fabricated on Si substrate. Sizes of the patterned holes were controllable by PMMA molecular weight.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.504-504
• /
• 2011

최근 디지털 프린팅 기술의 핵심기술로 떠오르고 있는 잉크젯 프린팅 기술은 최근 기존의 문서인쇄 뿐 아니라, 직물 인쇄, 태양전지 등의 다양한 반도체 소자 제조에 널리 활용되고 있으며, 점차 그 응용 분야를 넓혀가고 있다. 특히 thermal 방식의 잉크젯 피린팅 기술은 etching, thin film process, lithography등의 반도체 공정 기술을 이용하여 제작할 수 있기 때문에, 현재 잉크젯 프린팅 기술은 대부분 thermal 방식을 체택하고 있다. 이러한 thermal 잉크젯 프린팅 방법에서는 잉크를 토출시키기 위하여, 전기적 에너지를 열에너지로 전환하는 전자저항막층이 필수적으로 필요하게 되는데, 이러한 전자저항막층은 수백도가 넘는 고온 및 잉크와 접촉으로 인한 부식 및 산화 문제가 발생할 수 있는 열악한 환경에서 사용되므로, Ta, SiN과 같은 보호층을 필수적으로 필요로 한다. 그러나 최근 잉크젯 프린터의 고해상도 고속화, 대면적 인쇄성 등과 같은 다양한 요구 증가에 따라, 잉크젯 프린터의 저전력 구동이 이슈로 떠올라 열효율에 방해가 되는 보호층을 제거할 필요성이 제기되고 있다. 지금까지는 Poly-Si, $HfB_2$, TiN, TaAl, TaN _0.8 등의 물질들이 잉크젯 프린터용 전자저항막 물질로 연구되거나 실제로 사용되어져 왔으나, 이러한 물질들을 보호층을 제거하는 경우 쉽게 산화되거나, 부식되는 문제점을 가지고 있다. 따라서, 기존 전자저항막의 기능을 만족시키면서, 산화나 부식에 대한 강한 내성을 가져 보호층을 제거하더라도 안정적으로 구동이 가능한 하이브리드 기능성(히터 + 보호층)을 가지는 잉크젯 프린터용 전자저항막 물질의 개발이 시급한 실정이다. 본 연구에서는 자기조립특성을 가져 정밀제어가 가능한 원자층증착법(Atomic Layer Deposition)을 이용하여 원자/나노 단위의 미세 구조 컨트롤을 통해 내열 내산화 내부식성 저온도저항계수를 동시에 가지는 다기능성 전자저항막을 설계 및 개발하고자 하였다. 전자저항막 개발을 위하여 우수한 내부식 내산화성을 가지고 결정립 크기에 따른 온도저항계수 조절이 가능한 platinum group metal들과 전기 저항 및 내열성 향상을 위한 물질의 복합구조막을 원자증증착법으로 증착하였다. 또한, 전자저항막 증착시 미세구조와 공정 변수가 내부식성, 내산화성, 그리고 온도저항계수에 미치는 영향을 체계적으로 연구하여, proto-type의 inkjet printhead를 구현하였다.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.29 no.3
• /
• pp.105-124
• /
• 2011

TFT-LCD consists of LCD panel on the top, circuit unit on the side and BLU on the bottom. The recent development issues of BLU-dependent TFT-LCD have been power consumption minimization, slimmerization and size maximization. As a result of this trend, LED is adopted as BLU instead of CCFL to increase brightness and to reduce thickness. In liquid crystal displays, the light efficiency is below 10% due to the loss of light in the path from a light source to an LCD panel and presence of absorptive polarizer. This low efficiency results in low brightness and high power consumption. One way to circumvent this situation is to use a reflective polarizer between backlight units and LCD panels. Since a nano-wire grid polarizer has been known as a reflective polarizer, an idea was proposed that it can be used for the enhancement of the brightness of LCD. The use of reflective polarizing film is increasing as edge type LED TV and 3D TV markets are growing. This study has been carried out to fabrication of the nano-wire grid polarizer(NWGP) and investigated the brightness enhancement of LCD through polarization recycling by placing a NWGP between an c and a backlight unit. NWGPs with a pitch of 200nm were fabricated using laser interference lithography and aluminum sputtering and wet etching. And The NWGP fabrication process was using by the UV imprinting and was applied to plastic PET film. In this case, the brightness of an LCD with NWGPs was 1.21 times higher than that without NWGPs due to polarization recycling.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.8
• /
• pp.5586-5590
• /
• 2015

In this paper, the directed alignment methode of the DNA molecule between the Au electrodes was suggested for the application of nano devices. To fabricate the nano device coated DNA, 2-Aminoethanthiol(AET) was coated on Au electrodes which was formed using photo-lithography process on $SiO_2/Si$ substrates. In general, the AET that was a positive charge with $NH^{3+}$ was strongly combined under the electrostatic interaction with DNA molecule which had to be a negative charge. The DNA molecules could be easily aligned between Au electrodes coated with AET. The structures of the DNA molecules were investigated using AFM(Atomic force microscope), they were changed from single types to bundle according to the AET concentrations.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.67-67
• /
• 2018

The 5xxx series aluminum alloys are recently used in not only marine system but also automotive area because of a low density material, good mechanical properties and better resistance to corrosion. However, Aluminum alloys are less resistant than the purest aluminum such as 1xxx aluminum alloy. Electrochemical anodization technique has attracted in the area of surface treatment because of a simple procedure, a low-cost efficiency than other techniques such as lithography and a large volume of productivity, and so on. Here, The relationship between the corrosion behavior and the thickness of aluminum anodic oxide have been studied. Prior to anodization, The 5052 aluminum sheets ($30{\times}20{\times}1mm$) were degreased by ultra-sonication in acetone and ethanol for 10 minutes and eletropolished in a mixture of perchloric acid and ethanol (1:4, volume ratio) under an applied potential of 20V for 60 seconds to obtain a regular surface. During anodization process, Aluminum alloy was used as a working electrode and a platinum was used as a counter electrode. The two electrodes were separated at a distance of 5cm. The applied voltage of anodization is conducted at 40V in a 0.3M oxalic acid solution at $0^{\circ}C$ with appropriate magnetic stirring. The surface morphology and the thickness of AAO films was observed with a Scanning Electron Microscopy (SEM). The corrosion behavior of all samples was evaluated by an open-circuit potential and potentio-dynamic polarization test in 3.5wt% NaCl solution. Thus, The corrosion resistance of 5052 aluminum alloy is improved by the formation of an anodized oxide film as function of increase anodization time which artificially develops on the metal surface. The detailed electrochemical behavior of aluminum 5052 alloy will be discussed in view of the surface structures modified by anodization conditions such as applied voltages, concentration of electrolyte, and temperature of electrolyte.

• Polymer(Korea)
• /
• v.35 no.1
• /
• pp.87-93
• /
• 2011

We developed a fluorene-containing multifunctional binder polymer for LCD color filter resist, and employing the binder polymer, carbon black based black photoresist (CBR) was prepared in order to apply it to the black matrix (BM). To obtain the multifunction of the binder polymer, we synthesized bisphenol fluorene epoxy acrylate-containing unsaturated polyester and identified the binder polymer structure with $^1H$ NMR, GPC and FTIR. The corresponding BFEA-polyester binder polymer was compared with the commercially available acryl binder toward the application to the CBR. From the BM lithography test, we found that the synthesized BFEA-polyester binder had better photocrosslinking capability and alkali solubility. In addition, the newly developed binder gave a good process margin, good resolution and adhesion property on a glass substrate.

• Journal of the Korean Magnetics Society
• /
• v.25 no.1
• /
• pp.16-21
• /
• 2015

The micro device, coil, and channel for the biosensor integrated with the GMR-SV device based on the antiferromagnetic IrMn layer was fabricated by the light lithography process. When RBCs coupled with several magnetic beads with a diameter of $1{\mu}m$ passed on the micro channel, the movement of $RBC+{\mu}Beads$ is controlled by the electrical AC input signal. The $RBC+{\mu}Beads$ having a micro-magnetic field captured above the GMR-SV device is changed as the output signals for detection status. From these results, the GMR-SV device having the width magnitude of a few micron size can be applied as the biosensor for the analysis of a new magnetic property as the membrane's deformation of RBC coupled to magnetic beads.