• 한국생산제조학회지
• /
• 제19권6호
• /
• pp.731-738
• /
• 2010

Cavitation is described by formation and collapse of the bubbles in a liquid when the ambient pressure decreases. Formed bubbles grow and collapse by change of pressure, and when they collapse, shockwave by high pressure is generated. In general, bubble behavior can be described by Rayleigh-Plesset equation under adiabatic or isothermal condition and hence, phase shift by the pressure change in a bubble cannot be considered in the equation. In our study, a numerical model is developed from the mathematical model considering the phase shift from the previous study. In the developed numerical model, size of single spherical bubble is calculated by the change of mass calculated from the change of the ambient pressure in a liquid. The developed numerical model is verified by a case of liquid flow in a narrow channel.

• 한국전기전자재료학회논문지
• /
• 제14권3호
• /
• pp.257-262
• /
• 2001

Single crystalline films of La doped YIG(yttrium iron garnet) were grown by the liquid phase epitaxy. The lattice constants of films obtained by DCD(double crystalline diffractometer) measurement increased with increasing La contents in films. In particular, lattice constants of films grown wiht Y/La=20 solution were nearly same as those of GGG (gadolinium gallium garnet) substrate. The saturation magnetization measured with VSM (vibrating sample magnetometer) was about 1750Gauss which is the same as that of pure YIG irrespective of La contents in films. FMR(ferromagnetic resonance) linewidth of La doped YIG was smaller than that of pure YIG. Since appropriate La doping decreases the lattice mismatch between film and substrate, the FMR linewidth was Y/La=20 in this experiment.

• 한국가시화정보학회지
• /
• 제11권1호
• /
• pp.34-40
• /
• 2013

Gas/liquid two-phase ejector is a device without moving parts, in which liquid is used to drive gas of a low-pressure source. In this paper, the hydrodynamic characteristics of a vertical down type two-phase ejector were studied using an air-water loop system. Entrained air flow rates were measured with inlet and outlet pressures of the ejector with varying water flow rate. Homogeneous bubbly flows in the discharge pipe were confirmed by the high speed flow visualization method. Quantitative measurements of void fraction were made using a newly developed fiber optic probe system.

• 한국자동차공학회논문집
• /
• 제9권6호
• /
• pp.1-7
• /
• 2001

Recently, several LPG engines for heavy-duty vehicles have been developed, which can replace some diesel engines that are one of a main source for air pollution in urban area. As a preliminary study on the liquid phase LPG injection (hereafter LPLI) system applicable to a heavy duty LPG engine, the engine output and combustion performance were investigated with various combustion chambers and fuel compositions using a single cylinder engine equipped. Experimental results revealed that ellipse, double ellipse and nebula type combustion chamber made a more advantage in breaking swirl flow into small turbulence scale than bathtub type. Especially, performance of nebula type showed most highest efficiency and engine output under lean mixture conditions. An investigation fur various LPG fuel compositions was also carried out, and revealed that the case with 40% propane and 60% butane shows the lowest efficiency at stoichiometry, however, as the mixture became leaner its efficiency increased and became even higher for 100% propane case.

• Journal of Welding and Joining
• /
• 제19권1호
• /
• pp.82-87
• /
• 2001

The creep-rupture and low cycle fatigue properties of transient liquid phase bonded joints of Ni-base single crystal superalloy, CMSX-2 was investigated using MBF-80 insert metal. The (100) orientation of bonded specimen was aligned perpendicular to the joint interface. CMSX-2 was bonded at 1523K for 1.8ks in vacuum, optimum bonding condition. The creep rupture strength and rupture lives of the joints were the almost identical to ones of the base metal. SEM observation of the fracture surfaces of joints after creep rupture test revealed that the fracture surfaces classified three types of region, ductile fracture surface, cleavage fracture surface and interfacial fracture surface. The low cycle fatigue properties of the joints were also the same level as those of base metal. The elongation and reduction of area values of joints were comparable to those of base metal while fell down on creep rupture condition of high temperature.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.537-537
• /
• 2012

We have studied a fabrication of vapor phase polymerized Poly(3,4-ethylenedioxythiophene) (PEDOT) nanowire arrays for the first time. The vapor-phase polymerization (VPP) technique is a bottom-up processing method that utilizes the organic arrangement of macromolecules to easily produce ordered aggregates, including on the nanoscale, or prepare thin films of self-assembled molecules, micropatterns, or modified microstructures of pure conducting polymers. Also, liquid-bridge-mediated nanotransfer molding (LB-nTM), which was reported as a new direct patterning method recently, is for the arrayed formation of two- or three-dimensional structures with feature sizes as small as tens of nanometers over large areas up to 4 inches across and is based on the direct transfer of various materials from a mould to a substrate through a liquid bridge between them. The PEDOT nanowires grown by VPP method and transferred on a substrate to use LB-nTM method have been fabricated to single crystal PEDOT nanowires investigated Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM), Selected Area Electron Diffraction (SAED), X-Ray Diffraction (XRD), X-ray Photoelectron Spectroscopy (XPS), and electrical properties.

• 한국염색가공학회지
• /
• 제23권2호
• /
• pp.146-153
• /
• 2011

Silver nano-particles have been synthesized by liquid phase reduction method and alcohol reduction process. Silver nano-particles of the size 30 ~ 40 nm were formed successfully by alcohol reduction process. The formation, structure, morphology and size of silver nano-particles have been studied using FE-SEM, TEM, XRD, UV-visible spectroscopy. In particular high dispersion stability of the synthesized silver nano-particles could be obtained by PVP binding. Antibacterial activity of Ag/PET master batch sample made from its nano-silver particles showed excellent antibacterial activity against S. aureus and E. coli.

• 한국세라믹학회지
• /
• 제36권11호
• /
• pp.1243-1251
• /
• 1999

Densification behavior and microstructural evolution during the liquid-phase sintering of alumina-anorhite system were investigated as a function of MgO addition. When MgO component was added in either alumina or anorthite glass powder the aspect ratio of alumina grains decreased and concurrently the are of flat interface which was formed as a result of contact solid alumina gains rather increased. Consequently addition of MgO component in the Al2O3-amorthite system brought about suppression of the rearrangement of solid grains during the liquid phase sintering and then densification of specimens was also retarded.

• 한국세라믹학회지
• /
• 제34권10호
• /
• pp.1009-1014
• /
• 1997

Ammonia gas was blown into the solution of zirconium ion to induce precipitation of supersaturated zirconium ion at gas-liquid interface with increase in pH. The influence of pH on the phase and particle size of precipitate and calcined powders has been investigated. At pH 4.5 of zirconium solution, maximum yield of 98.7% was obtained. Above pH 4.5, there was no more increase of yield. Above pH 5.5, large aggregates consisting of primary particles were observed in precipitate and calcined powders. At pH 4.5, almost aggregate-free fine spherical zirconia powders were obtained.

• Journal of Welding and Joining
• /
• 제18권5호
• /
• pp.90-97
• /
• 2000

Effect of alloy elements on joinability of insert metal for liquid phase diffusion bonding of heat resistant alloys was investigated in this study. Also, optimum chemical composition of insert metal was explained using interpolation method. The insert metals utilized was commercial Ni-base amorphous foils and newly developed Ni-base filler metals with B, Si and Cr in this study. Melting point and critical interlayer width(CIW) decreased with increasing additional amount of B, Si and Cr, melting point lowering element of the insert metal. Optimized chemical composition of insert metals could be estimated by interpolation method. The optimum amount of B, Si, Cr addition into the insert metal were found to be about 3%, 4% and 3%, respectively. The measured characteristic values, melting point, microhardness in the bonded interlayer and CIW of the insert metals were the almost identical to ones of the calculated results by interpolation method.