• International Journal of Fluid Machinery and Systems
• /
• 제7권2호
• /
• pp.54-59
• /
• 2014

Particle Image Velocimetry combined with developed image processing method is adopted to study the liquid-solid two phase flow in the centrifugal pump impeller with crystallization phenomenon. The tracer particle is used to follow the liquid phase, which has the diameter between 8 to $12{\mu}m$. The crystal particle precipitates from the sodium sulfate solution does change the wavelength of the laser, and which has great laser scattering characteristics. The diameter of the crystal particle is larger than $20{\mu}m$. Through calculating the diameter of the particles in the image, the tracer particle and the crystal particle can be distinguished. By analyzing the experimental result, the following conclusion has been obtained. During the delay period, there is not any crystal particle and the pump performance has not been changed. As the crystallization process begins, the crystal nuclei appears from the supersaturation solution and grows larger with temperature decreasing, which has the tendency of moving towards the pressure side. The characteristics of liquid-solid two phase flow with crystallization phenomenon in the pump are obtained according to analysis of experimental results, and some guiding advices are presented to mitigate the crystallization phenomenon in pump impeller.

• 한국세라믹학회지
• /
• 제37권4호
• /
• pp.295-301
• /
• 2000

The effect of V2O5 addition on the low temperature sintering of Pb(Mn1/3Sb2/3)O3-PZT ceramics, which is known as a prominent material for piezoelectric transformer application was studied, and the densification behavior and piezoelectric characteristics of the samples as a function of heating rate were also examined. V2O5 led the system to liquid phase sintering by forming liquid phase during sintering, which accelerated densification through the particle rearrangement in the early stage of sintering. The liquid phase mostly existed at grain boundaries retarded the evaporation of PbO, while the densification temperature and the weight loss of V2O5-free samples were higher than those of samples with V2O5. Faster heating improved the densification of the samples regardless of V2O5 addition. The low temperature sintering at 100$0^{\circ}C$ was achieved in PMS-PZT ceramics with high density and reasonable dielectric and piezoelectric characteristics. This result revealed optimistic way to the development of multi-layered piezoelectric transformers.

• 센서학회지
• /
• 제25권1호
• /
• pp.57-64
• /
• 2016

To understand a two-phase flow, a liquid film thickness is one of the important factors. A lot of researches have been performed to measure liquid film thickness with various approaches. Recently, an electrical conductance method which uses the conductivity of the liquid film has been widely applied on measuring the liquid film thickness. Though the electrical method has an advantage in high spatial resolution, as the conductivity of liquid can be affected by its temperature variation, the conventional electrical conductance methods have a limitation in being applied on varying temperature conditions where a heat transfer is involved. The purpose of this study is to develop a three-ring liquid film sensor that overcomes the limitation of the conventional method. The three-ring conductance method can measure the film thickness regardless of temperature variation by compensating the change of liquid conductivity. Considering its application on a wide range of conditions such as high temperature or curved surfaces, the sensor was fabricated on flexible printed circuit board (FPCB) in this study. This paper presents the concept of the measurement method, design procedure, prototype sensor fabrication and calibration results.

• 한국분무공학회지
• /
• 제1권3호
• /
• pp.20-28
• /
• 1996

It is well known that drag reduction in single phase liquid flow is affected by polymer material, molecular weight, polymer concentration, pipe diameter, and flow velocity. Drag reduction in two phase flow can be applied to the transport of crude oil, phase change system such as chemical reactor, pool and boiling flow, and to present cavitation which occurs in pump impellers. But the research of drag reduction in two phase flow is not sufficient. The purpose of the present work is to evaluate the drag reduction by measuring pressure drop, void fraction whether polymer is added in the horizontal two phase system or not. Experiment has been conducted in a test section with 24 m of the inner diameter and 1,500 mm of the length. The used polymer materials are two kinds of polyacrylamide[PAAM] and co-polymer[A611P]. The polymer concentration was varied with 50, 100 and 200 ppm under the same experimental conditions. Experimental results were shown that the drag is higher reduced by co-polymer rather than polyanylamide.

• 한국재료학회지
• /
• 제9권4호
• /
• pp.335-340
• /
• 1999

The hot cracking phenomena and phase behaviors during hot working process of Cu-Ni bearing hot rolled steels were investigated by a $90^{\circ}$bending tests, BSE image analysis and EDS analysis. For aNi-free 1.2% Cu bearing steel, the surface hot cracking occurred about $1100^{\circ}C$ due to a liquid state Cu-enriched phase formed continuously at the interface between oxide scale and matrix. The liquid Cu-enriched phase penetrated into austenite grain boundaries and caused surface cracking during the hot working. In case of 0.6% Ni containing 1.2% Cu-Ni bearing steel, solid state Cu-Ni-riched phase existed at the scale/matrix interface as a discontinuous type. But the higher addition of 1.2% Ni, solid state Ni-Cu-riched phase was formed dominantly in the oxide scale. It was found that the addition of Ni suppressed the surface cracking of 1.2% Cu bearing steel by eliminating the liquid state Cu-enriched phase.

• Carbon letters
• /
• 제13권3호
• /
• pp.133-138
• /
• 2012

According to kinetic mechanisms, liquid phase polymerization and solid phase polymerization are different in acrylonitrile (AN) polymerization, and so the relationship between the contribution ratio and molecular weight distribution (MWD) was obtained through theoretic analysis. The precipitation homopolymerization of AN was carried out in a mixture solution of dimethyl sulfoxide (DMSO) and water at $50{\sim}65^{\circ}C$ using ${\alpha}$,${\alpha}^{\prime}$-azobisisobutyronitrile as an initiator. The contribution ratio decreased and approached 0; the MWD also decreased and approached 2 with the increase of the $H_2O$/DMSO ratio from 10/90 to 90/10. The experimental data were found to coincide well with the theoretical equation derived from the mechanisms.

• 분석과학
• /
• 제22권2호
• /
• pp.148-151
• /
• 2009

역상 액체 크로마토그래피에서 다당유도체 선택자가 공유결합된 키랄 컬럼인 Chiralpak IB을 사용하여 N-FMOC $\alpha$-amino acid의 광학 이성질체의 분리를 수행하였다. 공유결합된 키랄 컬럼인 Chiralpak IB에서 여러 역상 이동상 조건들이 광학분할의 선택성과 분리인자, 머무름시간에 미치는 영향을 보여주었다. 또한 역상 액체 크로마토그래피에서 N-FMOC $\alpha$-amino acid의 광학 이성질체의 분리 결과를 순상 액체 크로마토그래피 결과와 비교하였는데 순상이동상을 사용한 것보다는 대체적으로 낮은 광학분할을 보여주었다.

• The Korean Journal of Ceramics
• /
• 제5권3호
• /
• pp.205-210
• /
• 1999

The thermodynamic properties and phase diagram of the$ PbO-ZrO_2$ system have been critically assessed using the Thermo-Calc program. Excess Gibbs energies were expressed by Redlich-Kister polynomials for the solid phases, by the two-sublattice ionic liquid model for the liquid phase and by the compound energy model for the solid solution phase. All solid phases were treated as stoichimetric compounds.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2004년도 춘계 학술발표대회 개요집
• /
• pp.87-89
• /
• 2004

Brazing is an indispensable manufacturing technology for liquid rocket engine. In this study, for LRE injector, stainless steel 316L was used of base metal and Ni based MBF-20 of insert metal. The brazing and diffusion was carried out under various conditions. There are solid phase and. residual liquid phase in the brazed joint. With increment of holding time, the amount of solid phase increased and the elements of base metal and insert metal compositionally graded. Boron diffused from insert metal came into base metal and made boride with Cr and Mo at the brazed joint of base metal and insert metal.

• Korea-Australia Rheology Journal
• /
• 제21권3호
• /
• pp.161-173
• /
• 2009

This study analyzes especially drag and lift models recently developed for fluid-solid, fluid-fluid or liquid-liquid two-phase flows to understand their applicability on the computational fluid dynamics, CFD modeling of pulsatile blood flow. Virtual mass effect and the effect of red blood cells, RBCs aggregation on CFD modeling of blood flow are also shortly reviewed to recognize future tendencies in this field. Recent studies on two-phase flows are found as very useful to develop more powerful drag-lift models that reflect the effects of blood cell's shape, deformation, concentration, and aggregation.