• 한국컴퓨터산업학회논문지
• /
• 제7권4호
• /
• pp.427-436
• /
• 2006

운동하는 물체의 동특성 해석을 위한 상태 공간 모델 방식이 컴퓨터에 의한 미분방정식 해석의 수학적인 도구로서 도입되었다. 시스템 표현이 간단한 행렬 연산 형태로 이루어지므로 선형 및 비선형, 시변 및 시불변 시스템과 단변수 및 다변수 시스템 등에 대하여 통일된 방식의 모델이 사용가능하다. 그리고 이러한 상태 공간 모델을 해석하기위해서는 복잡한 벡터 연산을 하여야 하지만 패킷 소프트웨어의 특정함수를 사용하여 쉽게 해석할 수가 있다. 그러나 최근에는 상용 프로그램의 발전에 따라 동특성 해석을 위한 상태 공간 모델을 대화형 도형 처리를 하여 매우 간단하게 동특성을 시뮬레이션 할 수 있는 방법이 제공되고 있다. 본 논문은 운동하는 물체의 동특성 해석을 하는 데 교육용으로 활용할 수 있는 시뮬레이터를 개발하는 목적으로 항공기의 세로 동특성 해석을 위한 시뮬레이션을 수행하고자 하였으며 항공기 세로 안정성에 대한 과도응답 특성을 해석하는 시뮬레이터를 설계하였다.

• 한국생산제조학회지
• /
• 제23권2호
• /
• pp.178-185
• /
• 2014

This paper describes a fabrication multiplexing sensor probe that employs a fiber Bragg grating(FBG) based on multiple measurements to determine the blade deflection of a wind power generator the reliability analysis of this probe is also presented. To diminish the temperature sensitivity of the FBG sensor, we form multiple CFRPs onto the upper and lower layers of the FBG and package it with an epoxy resin. As a result, the depth of the CFRP is 1mm, and the temperature sensitivity is $2.39pm/^{\circ}C$. We construct a sensor network utilizing the fabricated sensor with a blade beam model. As the number of pendulums is increased on the fore-end of the beam, the strain value is measured. The strain variation is calculated from the measurement of the load on the blade beam model by monitoring the strain of the FBG sensor. When the linear equation is applied, the strain error is 0.4% and when the finite difference method is used, the tip deflection error is 3.3%. The displacement error derived from the strain value of the FBG sensor is 4.39%. The calculated result between the measured value of the dead-end of the beam and the strain is less than 2.46% tip distortion error. Therefore, our proposed multiplexing sensor probe is a low-cost and high-reliability solution for a commercial wind power generator.

• 한국농공학회지
• /
• 제30권4호
• /
• pp.134-153
• /
• 1988

This paper was carried out to investigate the existence of a unique stress- strain behavior by obtaining some factors influencing the time dependent stress- strain behavior of clay. The results obtained from this study were summarized as follows ; 1. The relationship between stress ratro and strain in normally consolidated clay was in- dependent on pre-shear consolidation pressure. Therefore, shear strain could be expressed as a function with stress ratio. 2. The constitutive equation of shear strain on Modified Carn Clay Model coincided better with the observed value than Cam Clay Model. 3. The relationships between deviator stress and shear strain, between pore water pressure and shear strain were unified by the mean equivalent pressure. 4. The shear strain contour in norrnally consolidated clay was increased linearly through origin, but that in overconsolidated clay was not in accordance with the result of the former. 5. Because the effective stress path of normally consolidated clay was unified by the mean equivalent pressure, state boundary surface in (e,p,q) space was transformed into two dimensional surface. But it was considered to be suitable that the unified stress- strain in overconsolidated clay be expressed by a function with overconsolidation ratio. 6. The deviator for constant strain was increased linearly with increment of strain rate ($\varepsilon$) on semi-log scale, but pore water pressure was decreased. 7. The behavior of stress relaxation was transformed from linear to curvilinear with inc - rement of strain rate before stress relaxation test, and pore water pressure was increased in total range. 8. The strain of creep was increased linearly with increment of time on semi-log scale. The greater the strain rate before creep test became, the greater the increment of strain of creep became. And the pore water pressure during creep test was increased generally with increment of time on semi-log scale.

• 한국축산식품학회지
• /
• 제36권2호
• /
• pp.262-266
• /
• 2016

This study evaluated the growth kinetics of Salmonella spp. in processed meat products formulated with low sodium nitrite (NaNO₂). A 5-strain mixture of Salmonella spp. was inoculated on 25-g samples of sausages formulated with sodium chloride (NaCl) (1.0%, 1.25%, and 1.5%) and NaNO₂ (0 and 10 ppm) followed by aerobic or vacuum storage at 10℃ and 15℃ for up to 816 h or 408 h, respectively. The bacterial cell counts were enumerated on xylose lysine deoxycholate agar, and the modified Gompertz model was fitted to the Salmonella cell counts to calculate the kinetic parameters as a function of NaCl concentration on the growth rate (GR; Log CFU/g/h) and lag phase duration (LPD; h). A linear equation was then fitted to the parameters to evaluate the effect of NaCl concentration on the kinetic parameters. The GR values of Salmonella on sausages were higher (p<0.05) with 10 ppm NaNO₂ concentration than with 0 ppm NaNO₂. The GR values of Salmonella decreased (p<0.05) as NaCl concentration increased, especially at 10℃. This result indicates that 10 ppm NaNO₂ may increase Salmonella growth at low NaCl concentrations, and that NaCl plays an important role in inhibiting Salmonella growth in sausages with low NaNO₂.

• 한국콘텐츠학회논문지
• /
• 제14권9호
• /
• pp.350-361
• /
• 2014

본 연구에서는 15세에서 17세의 청소년들을 대상으로 치과치료에 대한 공포감의 일반적인 경향과 관련변인들에 따라 공포감이 어떻게 차이가 나며, 이들 변인들이 치과치료에 대한 공포감에 영향을 미치는 정도와 인과관계를 밝히고자 하였다. DFS, DBS 및 GFS를 포함한 설문도구와 청소년의 특성에 관한 문항들로 구성된 설문지를 이용하였고, SPSS를 이용하여 단변량 분석을 시행한 후 LISREL 8.12를 사용하여 공변량 구조모형을 분석하였다. DFS (0.957), DBS (0.916) 및 GFS (0.910)의 Cronbach 신뢰도 계수가 모두 0.9이상으로 높게 나타났고, 자신의 치아상태가 건강하지 않다고 생각할수록, 최근 구강 내 동통을 경험했을 경우, 치과치료 시 동통을 강하게 느꼈을 경우, 그리고 치료 시 동통을 자주 경험했을 경우와 치과약속을 어긴적이 있을 경우에 그렇지 않은 경우보다 치과치료에 대한 공포감의 수준이 통계적으로 유의하게 높아지는 추세로 나타났다. 구조방정식 모형의 적합도는 양호하게 나타났으며, 치과치료시 동통정도와 동통 횟수, 치과약속을 어긴 횟수, 치과의사에 대한 불신감 그리고 일반적인 공포감이 치과치료와 관련된 공포감에 정(+)의 직접효과가 있었다.

• 대한치과교정학회지
• /
• 제46권3호
• /
• pp.171-179
• /
• 2016

Objective: The primary aim of the study was to generate new prediction equations for the estimation of maxillary and mandibular canine and premolar widths based on mandibular incisors and first permanent molar widths. Methods: A total of 2,340 calculations (768 based on the sum of mandibular incisor and first permanent molar widths, and 1,572 based on the maxillary and mandibular canine and premolar widths) were performed, and a digital stereomicroscope was used to derive the the digital models and measurements. Mesiodistal widths of maxillary and mandibular teeth were measured via scanned digital models. Results: There was a strong positive correlation between the estimation of maxillary (r = 0.85994, $r^2=0.7395$) and mandibular (r = 0.8708, $r^2=0.7582$) canine and premolar widths. The intraclass correlation coefficients were statistically significant, and the coefficients were in the strong correlation range, with an average of 0.9. Linear regression analysis was used to establish prediction equations. Prediction equations were developed to estimate maxillary arches based on $Y=15.746+0.602{\times}sum$ of mandibular incisors and mandibular first permanent molar widths (sum of mandibular incisors [SMI] + molars), $Y=18.224+0.540{\times}(SMI+molars)$, and $Y=16.186+0.586{\times}(SMI+molars)$ for both genders, and to estimate mandibular arches the parameters used were $Y=16.391+0.564{\times}(SMI+molars)$, $Y=14.444+0.609{\times}(SMI+molars)$, and $Y=19.915+0.481{\times}(SMI+molars)$. Conclusions: These formulas will be helpful for orthodontic diagnosis and clinical treatment planning during the mixed dentition stage.

• 국제지역연구
• /
• 제13권2호
• /
• pp.475-504
• /
• 2009

본 연구는 한국의 소비자들과 수입명품과의 실증관계를 분석하는 것으로 소비자가 구매하려고 하는 수입명품에 대한 원산지 이미지, 브랜드 이미지, 객관적인 제품 특성, 주관적인 소비자 특성 등의 속성(Product Attributes)이 소비자 제품구매의도와 제품선호도에 왜, 어떻게, 얼마나 영향을 실증적으로 미치는가를 계량적으로 분석하는 데에 있다고 할 수 있다. 이를 위한 세부적인 연구방향 다음과 같다. 첫째, 원산지 이미지와 브랜드 이미지가 수입명품의 선호도에 미치는 각각의 영향을 파악한다. 둘째, 소비자가 수입명품을 선택할 때, 구매리스크가 다른 제품특성이 소비자의 제품선호도에 영향을 미치는 원산지효과의 차이를 분석한다. 셋째, 제품선호도에 영향을 미치는 원산지 이미지와 브랜드 이미지의 중요도를 상호 비교함으로써 제품특성이 다른 제품 간의 차이를 규명한다. 넷째, 한국소비자의 구매태도를 분석하여 상호 비교함으로써 연구결과의 보편성을 조사하고 입증하는데 초점을 맞춘다. 분석에 사용된 실증분석방법은 구조방정식모델링이며 통계프로그램으로 Lisrel 7.0을 활용하였다.

• Advances in nano research
• /
• 제14권3호
• /
• pp.211-224
• /
• 2023

This work presents a modified analytical model for the bending behavior of axially functionally graded (AFG) carbon nanotubes reinforced composite (CNTRC) nanobeams. New higher order shear deformation beam theory is exploited to satisfy parabolic variation of shear through thickness direction and zero shears at the bottom and top surfaces.A Modified continuum nonlocal strain gradient theoryis employed to include the microstructure and the geometrical nano-size length scales. The extended rule of the mixture and the molecular dynamics simulations are exploited to evaluate the equivalent mechanical properties of FG-CNTRC beams. Carbon nanotubes reinforcements are distributed axially through the beam length direction with a new power graded function with two parameters. The equilibrium equations are derived with associated nonclassical boundary conditions, and Navier's procedure are used to solve the obtained differential equation and get the response of nanobeam under uniform, linear, or sinusoidal mechanical loadings. Numerical results are carried out to investigate the impact of inhomogeneity parameters, geometrical parameters, loadings type, nonlocal and length scale parameters on deflections and stresses of the AFG CNTRC nanobeams. The proposed model can be used in the design and analysis of MEMS and NEMS systems fabricated from carbon nanotubes reinforced composite nanobeam.

• Advances in nano research
• /
• 제16권3호
• /
• pp.289-301
• /
• 2024

In this work, an analytical model employing a new higher-order shear deformation beam theory is utilized to investigate the bending behavior of axially randomly oriented functionally graded carbon nanotubes reinforced composite nanobeams. A modified continuum nonlocal strain gradient theory is employed to incorporate both microstructural effects and geometric nano-scale length scales. The extended rule of mixture, along with molecular dynamics simulations, is used to assess the equivalent mechanical properties of functionally graded carbon nanotubes reinforced composite (FG-CNTRC) beams. Carbon nanotube reinforcements are randomly distributed axially along the length of the beam. The equilibrium equations, accompanied by nonclassical boundary conditions, are formulated, and Navier's procedure is used to solve the resulting differential equation, yielding the response of the nanobeam under various mechanical loadings, including uniform, linear, and sinusoidal loads. Numerical analysis is conducted to examine the influence of inhomogeneity parameters, geometric parameters, types of loading, as well as nonlocal and length scale parameters on the deflections and stresses of axially functionally graded carbon nanotubes reinforced composite (AFG CNTRC) nanobeams. The results indicate that, in contrast to the nonlocal parameter, the beam stiffness is increased by both the CNTs volume fraction and the length-scale parameter. The presented model is applicable for designing and analyzing microelectromechanical systems (MEMS) and nanoelectromechanical systems (NEMS) constructed from carbon nanotubes reinforced composite nanobeams.

• 한국근적외분광분석학회:학술대회논문집
• /
• 한국근적외분광분석학회 2001년도 NIR-2001
• /
• pp.4101-4101
• /
• 2001

Information of body composition (fat and protein) in living animal is important to determine the nutrients requirement. Deuterium oxide (D2O) dilution techniques, as one of isotope dilution techniques have been useful for the prediction of body composition. However, the determination of D2O concentration is time consuming and complicated. Therefore this study was conducted to develop a new method to predict D2O concentration in plasma using near infrared spectroscopy technique (NIRS). Four dairy cows in early lactation were used. They were fed total mixed ration containing conr silage, timothy hay, and concentrates to make 17.0%CP and 14.0 MJDE/kgDM. Dosing D2O was at week 1,3 and 5 after parturition. After dosing D2O, the blood was collected from hour 0 to 72. Blood samples were then centrifuge at 3,000 rpm for 10 minutes to obtain plasma. D2O concentration was analyzed by gas chromatograph (deuterium oxide analyzable system, HK102, Shokotsusyou) after extracted from plasma by liophilization. Plasma sample was scanned by NIRS using Pacific Scientific (Neotec) model 6500 (Perstorp Analytical, Silver Spring, MD) in the range of wavelength from 1100 to 2500 nm. Calibration equation was developed using multiple linear regression. Sample from one animal (cow #550; n: 74) was used for developing the calibration while the rest three animals were used for validating the equation. The range, R and SEC of the calibration set samples were 135-925 ppm, 0.93 and 48.1 ppm, respectively. Validation of the calibration equation for three individual cows was done and the average of NIR predicted value of D2O at each collection time from three weeks injection showed a high correlation. The range, r and 53 of plasma from cow #474 were 322-840 ppm,0.93 and 53.1; cow #478 were 146-951 ppm,0.95 and 39.8; cow #942 were 313-885 ppm,0.95 and 37.2, respectively. Judgement of accuracy based on ratio of standard deviation and standard error in validation set samples (RPD) for cow #474, #478 and #942 were 2.2,4.3 and 3.4, respectively. The error in application due to the variation between individual was considered smaller than the bias from collection period, however, this prediction can be overcome with correction of standard zero-minute concentration of blood. The results of this preliminary study on the use of NIRS for determination of D2O in plasma showed very promising as shown by a convenient and satisfy accuracy. Further study on various physiological stage of animal should be done.