• Journal of Biomedical Engineering Research
• /
• v.29 no.5
• /
• pp.392-399
• /
• 2008

Thin-film transistor (TFT) arrays for an x-ray detector require quite different design concept from that of the conventional active-matrix liquid crystal devices (AM-LCDs). In this paper anew design of TFT array which uses only SiNx for passivation layer is described to meet the detector performance and the product availability simultaneously. For the purpose of optimizing the design parameters of the TFT array, a Spice simulation was performed. As a result, some parameters, such as the TFT width, the data line capacitance, and the storage capacitance, were able to be fixed. The other parameters were decided within a permissible range of the TFT process especially the photolithography process and the wet etch process. Then we adapted the TFT array which had been produced by the proposed design to our prototype model (FDXD-1417 and evaluated it clinically by comparing with a commercial model (EPEX, Hologic, Beford, USA). The results say that our prototype model is slightly better than EPEX system in chest PA images. So we can prove the technical usefulness and the commercial values of the proposed TFT design.

• The Journal of Korean Physical Therapy
• /
• v.14 no.3
• /
• pp.373-406
• /
• 2002

This study was peformed to investigate the effects on skeletal muscle recovery with aqua-exercise; swimming to take the muscle endurance for 20 days on two group of white rats which were the low extremity atrophy group(control groups) by fixed for two weeks and aqua-exercise group(experimental groups) after it. The effects was observed with light and electron microcope to measure the morphological changes of muscle fibers. The results obtained were as follow. 1. Light microscope: In the case of control groups, quadriceps fibers had been irregular alignment, decreased muscle width and the irregular alignment nuclear appeared, as it is degenerative muscle fibers. In the case of experimental groups, the fibers had been regular alignment cells and fibers. The nucleus of muscle had been normal characterized by oval shape and fiber sarcomere clearly classified. 2. Electron microscope: In the case of control groups, there were the quadriceps which was Z-line streaming phenomenon induced at the sarcomere and cells nuclear separated from basal membrane. It was not only observed the sarcomere alignment irregularly and mitochondria damaged, but also vacuoles found. In the case of experimental groups, A band, I band, H band had been clearly appeared, classified at the myofibrils of quadriceps, and electronic dense M-line found in sarcomere. There were observed satellite cells and basal laminas that usually to be appeared at the time of mitochondrial development, skeletal muscle fiber regeneration or development. This results suggest that the aqua-exercise assisted to inhibit the degenerative morphological changes of skeletal muscle cells and help to recover from abnormal states. Especially, it is considered to effect on a normal structural formation.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.487-488
• /
• 2006

Picosecond (ps) laser micro-machining has emerged as an attractive method of fabricating high-precision microstructures, especially in metals. In this paper, a metallic mold for diffraction gratings is fabricated with a mode-locked 12 Ps $Nd:YVO_4$ laser. Laser pulses with a wavelength of 355nm are irradiated on the surface of NOK 80, a mold material, to generate line patterns. In order to minimize the line width, laser power is set just above the ablation threshold of NOK 80. Results show that the spectrum from the fabricated mold is good enough for some industrial application.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.10 no.5
• /
• pp.625-634
• /
• 1986

The strain distribution on a welded aluminum alloy transition joint produced by a static tensile load has been measured using a moire method combined with photoelastic coating method. The test specimens were made of aluminum alloy 6061-T6 and 2014-T6 butt welded with ER-4043 filler metal, and were post welded heat treated (solid solution heat treatment 502.deg. C 70min.) and precipitated (artificial aging 171.deg. C 600min.) to cause an abrupt change of mechanical properties between the base metals and weld metal. The photoelastic epoxy rubber was cemented on the specimen grating which had been reproduced on the specimen surface by using an electropolishing. The measurements were compared with strains computed by Finite Element Analysis. The following results were abtained. (1) The maximum strain were distributed along the center line in the transverse directiion of the weld metal. (2) The strain gradient along the fusion line increased approaching the V-groove tip and the maximum value was observed at a quarter of width from the V-groove tip. (3) The moire method combined with photoelastic coating was proved very useful for real time strain measurement in the welded aluminum alloy transition joint.

• Progress in Superconductivity
• /
• v.4 no.1
• /
• pp.74-79
• /
• 2002

High-speed probe made to test single flux quantum(SFQ) circuits was comprised of semi-rigid coaxial cables and microstrip lines. The impedance was set at 50 $\Omega$to carry high-speed signals without much loss. To do performance test of high-speed probe, we have attempted to fabricate a test chip which has a coplanar waveguide(CPW) structure. Electromagnetic simulation was done to optimize the dimension of CPW so that the CPW structure has an impedance of 50$\Omega$, matching in impedance with the probe. We also used the simulation to investigate the effect of the width of signal line and the gap between signal line and ground plane to the characteristics of CPW structure. We fabricated the CPW structure with a gold film deposited on Si wafer whose resistivity was above $1.5\times$10$_4$$\Omega$.cm. The magnitudes of S／sub 21／ of CPW at 6 ㎓ in simulations and in the actual measurements done with a network analyzer were: -0.1 ㏈ and -0.33 ㏈ (type A),-0.2 ㏈ and -0.48 ㏈ (type B), respectively. Using the test chip, we have successfully tested the performance of high-speed probe made for SFQ circuits. The probe showed the good performance overthe bandwidth of 10 ㎓.

• Journal of Korean Society of Steel Construction
• /
• v.10 no.2 s.35
• /
• pp.291-301
• /
• 1998

This paper is a study on the structural behavior of CFCT(Concrete-Filled Circular Tubular) column to H-beam connections with longitudinal rib. The important parameters are being longitudinal rib or not. variable column thickness(5.8mm. 9.2mm. 12.0mm. 15.0mm) around the joint between CFCT and H-beam and the width of flange to diameter. Test results are summarized for the strength, initial stiffness, failure mode and energy absorption capacities of each specimen. These are compared with the theoretical results(Yield line theory, numerical analysis). Therefore, the purpose of this paper is to investigate the stiffness and the strength of connections to evaluate the structural behavior of the CFCT column to H-beam connections with longitudinal rib.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2002.05a
• /
• pp.48-53
• /
• 2002

Sheet or plate bending is one of the most important industrial metal forming processes. And considerable attention has been focused on gaining a better understanding of many of bending characteristics. One of defaults in bending process is the springback. In this study, the springback characteristics of tailor-welded strips in U-bending process was investigated. Furthermore, not only the relationships between the springback and the process variables such as the geometry of the tools and thickness combination of workpiece but also the heat effect which affects the springback due to welding process was experimentally considered. First, tailor-welded strips are joined by the laser welding process and consisted of two types of thickness combinations of the SCPI sheet, 0.8t${\times}$1.2t and 0.8${\times}$1.6t to investigate the effect of different thickness combination on the springback. Secondly, two different directionally welded strips, one was welded along the centerline of the strip-width and the other was along the centerline of strip-length, were adopted to compare the effects of the location of weld line on the springback. And three punch profile radii of 3, 9, and 15 m were used. Some cases of the experimental results were simulated by using a commercial FEM code, PAM-STAMP to compare the experimental results to the analytical ones.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.98-99
• /
• 2012

Deposition of thin films using magnetron sputtering plasmas is a well-developed, classical technology. However, detailed investigations using advanced diagnostics are insufficient in magnetron sputtering, in comparison with plasma-aided dry etching and plasma-enhanced chemical vapor deposition. In this talk, we will show examples of diagnostic works on magnetron sputtering employing metal targets. Diagnostic methods which have fine spatial resolutions are suitable for magnetron sputtering plasmas since they have significant spatial distributions. We are using two-dimensional laser-induced fluorescence spectroscopy, in which the plasma space is illuminated by a tunable laser beam with a planer shape. A charge-coupled device camera with a gated image intensifier is used for taking the picture of the image of laser-induced fluorescence formed on the planer laser beam. The picture of laser-induced fluorescence directly represents the two-dimensional distribution of the atom density probed by the tunable laser beam, when an intense laser with a relatively wide line-width is used. When a weak laser beam with a relatively narrow linewidth is used, the laser-induced fluorescence represents the density distribution of atoms which feel the laser wavelength to be resonant via the Doppler shift corresponding to their velocities. In this case, we can obtain the velocity distribution function of atoms by scanning the wavelength of the laser beam around the line center.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.1 no.1
• /
• pp.15-23
• /
• 1977

This article is to study Dopo, man's traditional robe, which was worn by courtiers and scholars in Yi dynasty (AD 1392-1910). This article deals with its history and transition according to relative documents available, and presents its construction method with reference to relics. It is recorded that Dopo was first worn about the middle of the time of Yi dynasty. Dopo, however, seems to have its origin in the robe of Koguryo dynasty (BC 37-AD 668). Dopo was an ordinary robe to court officials, whereas Confucian scholars wore it as an official uniform or a ritual robe. ft was a long over-coat with V-neck line, and, round and wide sleeves. Dopo was so long that its edge reached wearer's ankels. One of the widest sleeves of relics was 58cm in size. Another unique characteristics Dopo had, were that its back cloth splited in two on center line, which was fully covered and added with-another cloth called 'Jeonsam'. Accordingly, a cloth-30cm in width and 30 yards in length-was needed to make Dopo. Since the reform of 1894 it was prohibited to wear, and then was replaced with Durumagi, a strait collar and narrow-sleeved robe.

• Laser Solutions
• /
• v.4 no.2
• /
• pp.21-28
• /
• 2001

The laser strengthening of 35kgf/㎟ and 60kgf/㎟ grade steel sheets is investigated by using CO$_2$ laser beam irradiation. The increase of tensile strength is dominated by the number of fully penetrated melting line. Also. the optimal laser input energy(hardness) and the number of melting line (melting width) are important variables for laser strengthening. Local strengthening by laser beam may be effective for the weight reduction of components where the tailored welded blank can not be applied.