• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.8 no.6
• /
• pp.1147-1152
• /
• 2004

This paper presents the design of a multi-standard NTSC/PAL video encoder. The encoder converts International Telecommunication Union-Recommendation (ITU-R) BT.601 4:2:2, ITU-R BT.656 or RGB inputs from various video sources into National Television Standards Committee (NTSC) or phase-alternate line (PAL) TV signals in both S-video and composite video baseband signals (CVBS). The encoder adopts multiplier-free structures to reduce hardware complexity. The hardware bit width of programmable digital filters for luminance and chrominance signals, along with other operating blocks, are carefully determined to produce high-quality digital video signals of 1 least significant bit (LSB) error or less. The proposed encode. is experimentally demonstrated by using the Altera APEX20K600EBC652-3 device.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.15 no.2
• /
• pp.73-79
• /
• 2001

This paper describes the simple single phase air-conditioner of power factor correction (PFC) circuit. By adopting PFC in the rectifier, we can reduce harmonic into power line, improve the efficiency and lower the total system cost compared to conventional inviter only. Also, system performance is improved by stabilizing the output voltage of PFC. To improve the current waveform of diode rectifiers, we propose a new operating principle for the voltage diode rectifiers. A circuit design method is shown by experimentation and confirmed simulation. It explained that compared conventional pulse-width modulated (PWM) inverter with half pulse-width modulated (HPWM) inverter HPWM inverter. Proposed HPWM inverter eliminated dead-time by lowering switching loss and holding over-shooting.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.57 no.3
• /
• pp.205-213
• /
• 2021

Two specimens of Hemitrygon izuensis (395.8-471.5 mm in disc width), belonging to the family Dasyatidae (Myliobatiformes), were collected from the waters off north-eastern Jeju-do Island in June 2016 and Pohang in August 2019. This species was characterized by having no spots on dorsal side of disc, white ventral tail fold and short preorbital snout length (15.6-18.3% of disc width). This species is similar to H. akajei and H. sinensis reported in Korea, but differs in small denticles on mid-line of dorsal surface of disc (absent in H. izuensis vs. present in H. akajei and H. sinensis), the length of ventral tail fold (28.1-31.0% in H. izuensis vs. 48.0-48.6% in H. akajei vs. 45.0% in H. sinensis), color of ventral tail fold (white in H. izuensis vs. black in H. akajei and H. sinensis) and small tubercles on the posterior part of tail (absent in H. izuensis vs. present in H. akajei and H. sinensis). We suggest a Korean name for H. izuensis as "I-ju-gal-saeg-ga-o-li" following Kim et al. (2019).

• Horticultural Science & Technology
• /
• v.28 no.5
• /
• pp.836-844
• /
• 2010

This study was carried out to investigate plant characteristics and nutritional components of the genetically modified (GM) Chinese cabbage and its control line grown in the central and northern parts of Korea in order to establish the evaluating protocol and standard assessment. The GM and non-GM Chinese cabbage was planted with normal and concentrated density at two locations in spring and fall of 2008 and 2009. From the statistic analysis on plant characteristics and nutritional components, there were not many significant differences between GM and non-GM Chinese cabbage. Only few differences in the plant characteristics were found between the dense and normal planting. In the dense planting, there was no significant difference between GM and non-GM Chinese cabbages except for three out of 18 plant traits, such as leaf shape, hairiness and midrib length. On the other hand, nine plant traits including leaf length, leaf width, leaf color, leaf shape, fresh weigh of ground part, number of leaf, midrib length, midrib width and root diameter were slightly different between GM and non-GM Chinese cabbage in the normal planting. In case of leaf length, midrib length, midrib width and fresh weigh of ground part, there were significantly differences not only between two lines, but also between two locations. From nutritional component analysis, only five fatty acids were identified in the Chinese cabbage: palmitic acid, oleic acid, stearic acid, linoleic acid and linolenic acid. Except linoleic acid, four fatty acids in one gram of dried sample from GM line were little higher than those from non-GM line. However, there were no significant differences in total contents of fatty acids not only between GM and non-GM Chinese cabbage line, but also between northern and central cultivating areas in the normal and dense planting. According to the composition of inorganic elements identified in the samples from both lines, there were six macro-elements, such as N, P, Ca, K, Mg and Na, and four micro-elements, Cu, Fe, Mn and Zn. Based on the result from PCA analysis, specific clusters were not found between GM Chinese cabbage and the control line, but found between two regions.

• Restorative Dentistry and Endodontics
• /
• v.19 no.2
• /
• pp.345-371
• /
• 1994

Restorative procedures can lead to weakening tooth due to reduction and alteraton of tooth structure. It is essential to prevent fractures to conserve tooth. Among the several parameters in cavity designs, cavity isthmus and depth are very important. In this study, MO amalgam cavity was prepared on maxillary first premolar. Three dimensional. finite element models were made by serial photographic method and cavity depth(1.7mm, 2.4mm) and isthmus (11 4, 1/3, 1/2 of intercuspal distance) were varied. linear, eight and six-nodal, isoparametric brick elements were used for the three dimensional finite element model. The periodontal ligament and alveolar bone surrounding the tooth were excluded in these models. Three types model(B, G and R model) were developed. B model was assumed perfect bonding between the restoration and cavity wall. Both compressive and tensile forces were distributed directly to the adjacent regions. G model(Gap Distance: 0.000001mm) was assumed the possibility of play at the interface simulated the lack of real bonding between the amalgam and cavity wall (enamel and dentin). When compression occurred along the interface, the forces were transferred to the adjacent regions. However, tensile forces perpendicular to the interface were excluded. R model was assumed non-connection between the restoration and cavity wall. No force was transferred to the adjacent regions. A load of 500N was applied vertically at the first node from the lingual slope of the buccal cusp tip. This study analysed the displacement, von Mises stress, 1 and 2 direction normal stress and strain with FEM software ABAQUS Version 5.2 and hardware IRIS 4D/310 VGX Work-station. The results were as follows: 1. G model showed stress and strain patterns between Band R model. 2. B model and G model showed the bending phenomenon in the displacement. 3. R model showed the greatest amount of the displacement of the buccal cusp followed by G and B model in descending order. G model showed the greatest amount of the displacement of the lingual cusp followed by B and R model in descending order. 4. B model showed no change of the displacement as increasing depth and width of the cavity. G and R model showed greater displacement of the buccal cusp as increasing depth and width of the cavity, but no change in the displacement of the lingual cusp. 5. As increasing of the width of the cavity, stress and strain were not changed in B model. Stress and strain were increased on the distal marginal ridge and buccopulpal line angle in G and R model. The possibility of the tooth fracture was increased. 6. As increasing of the depth of the cavity, stress and strain were not changed in B and G model. Stress and strain were increased on the distal marginal ridge and buccopulpal line angle in R model. The possibility of the tooth fracture was increased.

• International Journal of Highway Engineering
• /
• v.16 no.5
• /
• pp.91-98
• /
• 2014

PURPOSES : This study is to develop a automate road mapping system using ARASEO(Automated Road Analysis and Safety Evaluation TOol) for road management. METHODS : The road survey van named ARASEO(Automated Road Analysis and Safety Evaluation TOol) was used to generate highway drawings for Korea National Road number 37 automatically. In order to generate the highway drawings for purpose of road management, it is required to acquired the information for highway alignment, road width and road facilities such as safety barrier and road sign. Therefore the survey van acquired and analyzed the road width, median and guardrail data using rear side laser sensor of ARASEO and recognized the traffic control sign and chevron sign using foreside camera images. Also the highway alignment which is the basic information for highway drawing can be analyzed by acquisition the every 1m positional and attitude data using GPU and IMU sensor and developed algorithm. Finally, in this research the CAD based drawing software was developed to draw highway drawing using the analysis result from ARASEO. RESULTS : This study showed the comparison result of the surveyed road width and drawing data. To make the drawing of the road, we made the Autocad ARX program witch run in CAD menu interface. CONCLUSIONS : Using this program we can create the road center line, every 500m horizontal and vertical ground plan drawing automatically.

• Journal of Fashion Business
• /
• v.9 no.1
• /
• pp.79-88
• /
• 2005

The purpose of this study is to propose the design of the patient's clothes for a disabled child between 4 and 6. For this, in this study, I would present the following design plan which includes 3 upper garments, 2 trousers and a one-piece dress. In case of the damage on head and neck, a neck line should be deep and wide thereby providing ease to the clothes. To facilitate injection and dressing/undressing, there should be parting from neck to cuff which can be fixed by snap or button. By rolling up sleeves with strings inside the cuffs and fixating plaster cast with snap button outside the cuffs. In case of body cast with plaster cast around body part, front adjusting part should be wider and the width should be adjusted with strings. In case of hip spica cast which covers waist, I separated front part and rear part, fixated them with snap buttons, gave more width to front adjusting part with strings to adjust width, which constitute one-piece dress. In case of shoulder spica cast, the other shoulder which is not covered with plaster cast should be exposed, and to prevent clothes' coming down, strings with snap button or velcro should be attached over a shoulder so that the length of the strings can be adjusted. In case of applying plaster cast or aid to the whole part of a leg, one part of trousers should be shorter so as to expose the injured part and there should be a parting with strings or velcros on the side for easy dressing/undressing. When plaster cast or splint is short, The strings are meant to adjust length of trousers. The partings are located 2 cm from side lines toward the center.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.5
• /
• pp.2018-2030
• /
• 2015

A two stage ac drive configuration consisting of a single-phase line commutated rectifier and a three-phase voltage source inverter (VSI) is very common in low and medium power applications. The deterministic pulse width modulation (PWM) methods like sinusoidal PWM (SPWM) could not be considered as an ideal choice for modern drives since they result mechanical vibration and acoustic noise, and limit the application scope. This is due to the incapability of the deterministic PWM strategies in sprawling the harmonic power. The random PWM (RPWM) approaches could solve this issue by creating continuous harmonic profile instead of discrete clusters of dominant harmonics. Insufficient filtering at dc link results in the amplitude distortion of the input dc voltage to the VSI and has the most significant impact on the spectral errors (difference between theoretical and practical spectra). It is obvious that the sprawling effect of RPWM undoubtedly influenced by input fluctuation and the discrete harmonic clusters may reappear. The influence of dc link fluctuation on harmonics and their spreading effect in the VSI remains invalidated. A case study is done with four different filter capacitor values in this paper and results are compared with the constant dc input operation. This paper also proposes an ingenious RPWM, a ripple dosed sinusoidal reference-random carrier PWM (RDSRRCPWM), which has the innate capacity of suppressing the effect of input fluctuation in the output than the other modern PWM methods. MATLAB based simulation study reveals the fundamental component, total harmonic distortion (THD) and harmonic spread factor (HSF) for various modulation indices. The non-ideal dc link is managed well with the developed RDSRRCPWM applied to the VSI and tested in a proto type VSI using the field programmable gate array (FPGA).

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.11
• /
• pp.2538-2543
• /
• 2012

The Percutaneous Coronary intervention is a typical way of testing which could be performance to treat a stenosed region by inserting a stent using catheter. In this case, choosing the best stent amongst various kinds of stent for performing an intervention is the most difficult process. For the reason, a width of the blood vessel which is stenosed must be correctly measured to help an operator choose right size of stent. So based on pixel, a width of the blood vessel measured by using the way of Euclidean distance after designing a center-line of vessel from a certain point assigned by operator is shown as a profile in this study. This study would be used as a goof reference for operators when choosing right size of stent.

• Fashion & Textile Research Journal
• /
• v.10 no.1
• /
• pp.83-91
• /
• 2008

This study was designed to figure out the changes in elderly women's foot size and shape by aging, to propose size specification for elderly women's shoes, and to produce regression equations using representative measurements items to estimate other measurements usually hard to get. Subjects were 118 women of 30-59 years and the 227 elderly women over 60 years. Martin's anthropometry was done on the right foot of each subject for 25 items. And 11 indirect measurement items were measured on both foot printing sole outline and picture in profile taken by digital camera. For statistical analysis on the anthropometric measurements by SPSS program, analysis of variance, post-hoc test(SNK-test), crosstabulation, multiple correlation analysis, regression analysis were performed. The results of the study are as follows. Firstly, it was found that the foot figures of elderly women over 60 years were smaller in girth and width than those of below 60 years. In addition, it was revealed that a big toe and a little toe of elderly women showed a tendency concentrating to the central axis of feet. The foot index of elderly was smaller in width and girth. Secondly, foot size distribution table of elderly group showed wider size ranges and covered smaller sizes than the below the age of 60, meaning wide variation in foot size of elderly women. Thirdly, the multiple correlation analysis showed high correlation of foot length/girth to other measurements, suggesting these two items could be used as representative items for elderly women's shoe size specification as other age groups. Regression equations were produced using foot length/girth to estimate other measurements, suggesting such items could be estimated effectively and utilized in on/off-line shoe manufacturing shop as heel to big toe length, heel to little toe length, exterior malleouls width, instep girth, ankle girth, etc. These results imply prudent features of elderly women's foot as diversity of foot shape and wide size specification range should be applied for ergonomic shoe design for them.