• Structural Engineering and Mechanics
• /
• v.20 no.3
• /
• pp.313-334
• /
• 2005

The paper presents a new approach for the analysis of slope stability that is based on the numerical solution of a differential equation, which describes the thrust force distribution within the potential sliding mass. It is based on the evaluation of the thrust force value at the endpoint of the slip line. A coupled approximation of the slip and thrust lines is applied. The model is based on subdivision of the sliding mass into slices that are normal to the slip line and the equilibrium differential equation is obtained as the slice width approaches zero. Opposed to common iterative limit equilibrium procedures the present method is straightforward and gives an estimate of slope stability at the value of the safety factor prescribed in advance by standard requirements. Considering the location of the thrust line within the soil mass above the trial slip line eliminates the possible development of a tensile thrust force in the stable and critical states of the slope. The location of the upper boundary point of the thrust line is determined by the equilibrium of the upper triangular slice. The method can be applied to any smooth shape of a slip line, i.e., to a slip line without break points. An approximation of the slip and thrust lines by quadratic parabolas is used in the numerical examples for a series of slopes.

• Journal of Astronomy and Space Sciences
• /
• v.35 no.1
• /
• pp.7-18
• /
• 2018

We have investigated the intensities and full width at half maximum (FWHM) of the high dispersion spectroscopic N III emission lines of AG Peg, observed with the Hamilton Echelle Spectrograph (HES) in three different epochs at Mt. Hamilton's Lick Observatory. The earlier theoretical Bowen line study assumed the continuum fluorescence effect, presenting a large discrepancy with the present data. Hence, we analyzed the observed N III lines assuming line fluorescence as the only suitable source: (1) The O III and N III resonance line profiles near ${\lambda}$ 374 were decomposed, using the Gaussian function, and the contributions from various O III line components were determined. (2) Based on the theoretical resonant N III intensities, the expected N III Bowen intensities were obtained to fit the observed values. Our study shows that the incoming line photon number ratio must be considered to balance at each N III Bowen line level in the ultraviolet radiation according to the observed lines in the optical zone. We also found that the average FWHM of the N III Bowen lines was about $5km{\cdot}s^{-1}$ greater than that of the O III Bowen lines, perhaps due to the inherently different kinematic characteristics of their emission zones.

• Proceedings of the KIEE Conference
• /
• 2004.11c
• /
• pp.22-24
• /
• 2004

This paper proposes a printing quality inspection system of film-type envelopment. Since the printing system is running at very high-speed (140m/min.) and the line error has very narrow width, we have to choose one-dimensional high-speed and high-resolution line scan camera. The vibration of the printing machine and the illumination environment make the inspection problem more harder. To obtain reliable inspection results, many software image processing techniques are applied and many parameters are tuned. The performance of the proposed system is proved by many simulations and long time real-plant experiments.

• The Bulletin of The Korean Astronomical Society
• /
• v.38 no.2
• /
• pp.62.1-62.1
• /
• 2013

We present the Exposure Time Calculator of IGRINS (Immersion Grating Infrared Spectrograph). The noises of IGRINS and the simulated emission line can be calculated from the combination of Telluric background emission and absorptions, the emission and transmission of the telescope and instrument optics, and the dark noise and the read noise of the infrared arrays. For the atmospheric transmissions, we apply the simulated spectra depending on the Precipitable Water Vapor (PWV) values. In case of calculation of noises, the user needs to input the expected target magnitude, the weather conditions, and the desired exposure time. In addition to the simulated emission line, the parameters of rest wavelength, line-flux, Doppler shift and line-width are needed. The output would be the expected signal-to-noise for each spectral resolution element. The source-code of IGRINS-ETC v2.1.1 is available to be downloaded on the World Wide Web.

• Textile Coloration and Finishing
• /
• v.18 no.5 s.90
• /
• pp.61-71
• /
• 2006

This paper addresses the factors hindering the image quality of lines in inkjet printed on polyester fabric as printing media. Lines were printed onto different types of polyester fabrics in warp and filling directions. Line image quality including line width, edge blurriness, and edge raggedness was assessed. The effect of capillary wicking on line image quality of printed spun polyester fabric is discussed. The factors on the image quality include printing position(top of the yam or between the yarn), printing direction(warp or filling), yarn structures(filament or spun), thread size(yam or fiber), finishing, and ink properties(evaporation rate). More than 30% differences in image quality results were observed by changing the printing location on the spun polyester fabric. The best results of the image quality were obtained with the printed plain and spun polyester fabrics. The fiber sizes may affect capillary size; therefore, the image quality can be dissimilar. Types of finishing materials and inks greatly improve the line image quality on spun polyester fabrics.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.3
• /
• pp.181-189
• /
• 2001

For the Tailor Welded Blank sheet used fur automobile body panel, the characteristics of fatigue crack propagation behavior were studied. The thickness of specimen was machined to be same (0.9+0.9mm) and different (0.9+2.0mm). As a base test, mechanical properties around welding zone were examined. The results indicated that there were no significant decreases in mechanical properties, but hardness around welding bead is 2.3 times greater than base material. The crack propagation rate was noticeably decreased around welding line and rapidly increased as it passed by welding line. Reviewing the shape of the crack propagation, crack width around welding line was wide around the welding zone due to retardation of crack growth, but it became narrow passing welding line due to decreased toughness. Elasto-Plastic analysis was performed by finite element analysis fur explaining the test results.

• Proceedings of the KIEE Conference
• /
• 1998.11c
• /
• pp.838-840
• /
• 1998

$BiNbO_4$ ceramics with 0.06wt% CuO, 0.1wt% $V_{2}O_{5}$ sintered at $900^{\circ}C$. The strip line chip filter has been design and fabricated by screen printing with silver electrode after tape casting. The characteristics of the fabricated filters were compared with the simulated results. In the strip line chip filter, insertion loss value of band pass width was 3.65[dB] and return loss was 8.9[dB] and center frequency was similar that simulation results.

• Proceedings of the IEEK Conference
• /
• 2003.11a
• /
• pp.31-34
• /
• 2003

In this paper, we describe a method for separating text lines in handwritten Korean address images. The most remarkable feature of the proposed method is to use a modified projection technique. named a partial projection technique. A projection based text line separation method which projects the whole address image in horizontal direction to find split points for text line separation cannot avoid failing separation in case of images with a little skew or overlap between vertically neighboring text lines. To overcome this problem, we have introduced a partial projection technique which splits an address image into a few partial address images to be equal width and then project them each horizontally. The experiment done with 989 handwritten Korean address images extracted from live mails shows the superiority of the proposed method. The correct text-line separation rate fir the testing images was about 91.5％.

• Laser Solutions
• /
• v.2 no.3
• /
• pp.52-61
• /
• 1999

The laser induced forward transfer(LIFT) technique employs a pulsed laser to transfer parts of a thin metal film from an optically transparent target onto an arbitrary substrate in close proximity to the metal film on the target. In this work, a two-step method, the combination of LIFT process, in which a Au film deposited on the $Al_2$O$_3$ substrate by Nd:YAG laser and subsequent Au electroless metal plating on the by LIFT process generated Au seed, was presented. The influence of laser parameters, wavelength, laser power, film thickness and overlap ratio of pulse tracks, on the shapes of deposit and conductor line after electroless plating is experimentally studied. As a results, the threshold power densities for ablation, deposition and metallization were determined and comparison of threshold value between the wave length 1064nm and the second harmonic generated 532nm. In odor to determine a possible application in the electronic industry, a smallest conduct spot size, line width and isolated line space were generated.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.24 no.1
• /
• pp.31-37
• /
• 2015

A laser line welder using a solid-state laser (Yb:YAG) has been manufactured for joining ultra-thin cold-rolled steel coils in steelworks. The coils to be welded primarily range from 0.15 to 0.3 mm in thickness and 800 to 1,100 mm in width. Because the steel plate is extremely thin, it is very important to control the stop positions of the clamp at cutting and welding points. In this study, both hydraulic proportional control valves and LVDT sensor embedded cylinders were used to precisely control and monitor the positions of clamps with complementary stoppers. As a result, the positions could be controlled within an error of ${\pm}30{\mu}m$. Erichsen cupping tests on the welded joints show that the Erichsen index ranges from 4.4 to 4.6 mm. Furthermore, the tensile strength of welding points is comparable to that of the base metal.