• Journal of Communications and Networks
• /
• v.13 no.5
• /
• pp.421-427
• /
• 2011

Problems encountered in IEEE 802.11 medium access control (MAC) design are interferences from neighboring or hidden nodes and collision from simultaneous transmissions within the same contention floors. This paper presents the selective decoding schemes in MAC protocol for multiple input multiple output ad-hoc networks. It is able to mitigate interferences by using a developed minimum mean-squared error technique. This interference mitigation combined with the maximum likelihood decoding schemes for the Alamouti coding enables the receiver to decode and differentiate the desired data streams from co-channel data streams. As a result, it allows a pair of simultaneous transmissions to the same or different nodes which yields the network utilization increase. Moreover, the presented three decoding schemes and time line operations are optimally selected corresponding to the transmission demand of neighboring nodes to avoid collision. The selection is determined by the number of request to send (RTS) packets and the type of clear to send packets. Both theoretical channel capacity and simulation results show that the proposed selective decoding scheme MAC protocol outperforms the mitigation interference using multiple antennas and the parallel RTS processing protocols for the cases of (1) single data stream and (2) two independent data streams which are simultaneously transmitted by two independent transmitters.

• Journal of IKEEE
• /
• v.23 no.1
• /
• pp.151-158
• /
• 2019

In this paper, we construct a Virtual D-STATCOM using a number of grid-connected inverters installed in solar and wind power plants and compensate the reactive power of the cable depending on the reactive power of the load of the power distribution system and the distance to the power distribution line We propose a method to compensate the reactive power of the PCC stage near the substation without installing the existing single large capacity D-STATCOM. The proposed method is verified by Matlab Simulink simulation and its operation principle and reactive power compensation.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.25 no.6
• /
• pp.459-468
• /
• 2020

The pole interaction of the line-commutated converter high-voltage direct current (HVDC) is analyzed, and a practical solution that uses a surge arrester is proposed. Jeju HVDC No. 2 is a double-monopole HVDC link that has a rated power capacity of 2 × 200 MW and was commissioned in 2012. During normal operation, Jeju HVDC No. 2 is operated in the bipolar mode to minimize the loss caused by the dedicated metallic return. However, when one pole of the inverter valve is bypassed, a commutation failure can occur in the other pole. This phenomenon is called pole interaction in this work. This pole interaction interrupts the HVDC power transfer for almost 2 s and may affect the stability of the power system. This research proposes the installation of a surge arrester at the inverter neutral, which can be an effective and practical solution for pole interaction. The HVDC system is analyzed, and the residual voltage of the surge arrester is determined. Detailed simulation using PSCAD/EMTDC demonstrates that the proposed method eliminates the pole interaction of the bipolar-operated HVDC.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.20 no.4
• /
• pp.86-97
• /
• 2006

For the design of DC traction power supply system at new Light Rail Transit(LRT) construction, it is very important to determine system configuration, location and power capacity of substation. However, a LRT system consists of a number of subsystems such as train movement, power supply and traction drives, which inevitably contains many complexities and diversities. The objective of this paper is to clarify and systematize the design procedure and its assessment for the electrification system of a LRT line. This paper discusses in detail our approach to system design and its assessment. The whole DC-feeding network configuration, characteristics of a train, and design method of substation arrangements is thoroughly investigated for the design. As a result of the investigations, the design procedure is clarified and systematized and a computer program for the design and evaluation of the system is developed using the most suitable iterative method with nodal equation. To verify the proposed design and its assessment procedure, case studies for the DC traction power supply system of a planed Korean LRT line are performed.

• Proceedings of the KAIS Fall Conference
• /
• 2012.05b
• /
• pp.512-516
• /
• 2012

Recently the Korean government's green energy growth policy has been taken at the national level due to the sufficient supply of renewable energy. Some specific technique should be taken in consideration for the operation of the grid voltage and power quality management. In this case, there may have some chance of operational problems. Typical problems arise when grid-connected solar power produced by Pacific sunshine. The power flow in the reverse direction can create overvoltage on the distribution line and gives value of malfunction on the system. Line voltage and overvoltage adjustment practice can stop these symptoms occurred. Under these circumstances, this paper presents an interconnection test devices for photovoltaic(PV) systems composed of distribution system simulator, PV system simulator and control and monitoring systems using the LabVIEW S/W, and simulates the customer voltage characteristics considering the 3 parameters on the introduction capacity for PV systems, system configuration and Power factor. This paper also proposes a new calculation algorithm for voltage profile to make comparison between calculation values and test device values. The results show that the simulation results for the normal operation characteristics of PV systems which are very practical and effective.

• Journal of Korean Society for Geospatial Information Science
• /
• v.20 no.2
• /
• pp.55-61
• /
• 2012

The primary factors of the LOS(Line-of-Sight) analysis process are terrain height, camera capacity, and canopy cover. The canopy cover rate differs depending on the changing season, and its value is influenced by the tree density, tree height, and etc. This study generated the canopy cover value based on relationship between NDVI(Normalized Difference Vegetation Index) and DMT(Density Measure % of Tree/Canopy Cover), which is a digital map attribute, and then performed the LOS analysis on six station of test sites. As results, It was found that NDVI and DMT are correlated with each other through the experiments. Based on this finding, new DMT map can be generated using NDVI. Also, There is a difference between the result of visibility analysis using the present DMT and one using a new DMT. Especially, the spatial distributions of the detected visible areas are significantly different between the two visibility analysis results.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.8
• /
• pp.863-870
• /
• 2003

The digital transmission system entered in a RF region as digital system use IC chips of the speeder edge rate and clock speed nowadays. Optical path really was used in order to obtain the more capacity. In this paper, we described importance of electrical interconnect to get the signal integrity in optical module by simulation and experiment. 12 channel${\times}$2.5 G/ps optical parallel transmitter modules were manufactured by two different method ; access lines with microstrip and stripline type. We have clearly shown that the optical module adopting microstrip type with S$\sub$11/ $\geq$ -10 dB presents distortion but the optical module adopting stripline type with S$\sub$11/ $\leq$ : 15 dB obtains eye opening in 2.5 Gbis optical eye pattern response.

• Journal of IKEEE
• /
• v.24 no.1
• /
• pp.364-367
• /
• 2020

This paper presents the off-grid PV-ESS system of sequential voltage control method applied to OR logic gate. The conventional off-grid PV-ESS system with the low-voltage series connection has problems due to capacity expansion. To solve these problems, this paper proposes a noble PV-ESS system with high efficiency and low cost by applying sequential voltage control technique of the high-voltage series connection of analog circuit type. The input voltage of DC to AC inverter can be converted from the low-voltage by the combinations of series connection of the conventional cascaded 24V solar cell unit modules to the high-voltage of 384V in battery. The output voltage of the battery was 384V as the each input voltage of three phase DC to AC inverter, and the each output voltage of three phase 10kW DC to AC inverter is designed to be AC380V@60Hz as the line to line rms voltage value. To prove the validity of the theoretical analysis by PSIM simulation, the operating characteristics of sequential voltage control system with OR logic gate were confirmed through experiment results.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.22 no.6
• /
• pp.26-33
• /
• 2008

This paper presents a new full-bridge soft switching PWM DC-DC converter circuit topology that adding one switcher, one lossless snubber quasi-resonance capacity to power source for general welding machine This full-bridge soft switching DC-DC convoter· topology can applicable 600[V] switching device (IGBT)incase of AC 400[V] common power source because the voltage of active switcher is 1/2 of DC bus line voltage. And low voltage hight current out)ut that first coil current is smaller than second coil current in high frequency transformer can be obtained with decreasing path loss in conventional DC bus line switcher. As it operate ZCS/ZVS in full range, high frequency, high efficiency and high output are implemented at low voltage and high DC current switching power supplies. All of this items are got from simulation and the result of experiment. If make up for the weak points of this proposed circuit, it will be used more easily for next generation TIG, MIG and MAG type of arc-welding machine.

• Journal of Platform Technology
• /
• v.8 no.2
• /
• pp.22-31
• /
• 2020

The construction and operation of industrial automation has been actively taking place from manufacturing plan to production for improving operational efficiency of production line and flexibility of equipment. ISO/TC184 is standardizing on operating methods that can share information of programmable device controllers such as PLC and IoT that are geographically distributed in the production line. In this study, the design of the cell controller consists of PLC group and IoT group that perform signals such as temperature sensors, gas sensors, and pressure sensors for thermal processes and corresponding motors or valves. The operation and analysis of the cell controller were performed using SDN(Software Defined Network) and the three types of process services performed in thermal processes are real-time transmission service, loss-sensitive large-capacity transmission service, and normal transmission service. The simulation result showed that the average loss rate improved by about 17% when the traffic increased before and after the application of the SDN route technique, and the delay in the real-time service was as low as 1 ms.