• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2005.06a
• /
• pp.299-303
• /
• 2005

A lighting control switch, extended to incorporate a power line communication technology, is developed. The system uses not an exclusive microprocessor but a general one, and developed PPM protocol. The coupling circuit is a type of an isolation LC filter, and the impedance of the circuit was designed as low as possible to extend signal transmission distance. The frequency of the carrier, considering the data length and signal attenuation as the length of power lines, was set at 250 kHz. Tests on a prototype in an indoor power lines have shown that the switch has a stable operation with the distance of power lines

• KIEAE Journal
• /
• v.12 no.1
• /
• pp.119-125
• /
• 2012

The objective of this study is to evaluate the electric lighting energy consumption carried out by Daysim program. A comparison between the measurement and simulated exterior global horizontal illuminance shows differences about 10% and it is very similar to the measurement. The interior illuminance simulated by Daysim are 18.9% lower than the measurement and simulated lighting energy consumption is 10% lower than the measurement. Corrected annual lighting energy simulation results show that the best case is the combination of occupancy switch-off and dimming system with automatic controlled blinds (E-3). In case of no blinds, it occasionally derives the minimum lighting energy consumption but it causes the glare, so we need to be careful for choosing the control strategy. For the overcast sky, the lighting energy consumption is not changed significantly by control strategy while the lighting energy in the clear sky is changed noticeably. So we must know the right strategy for each case to control the electric lights and blinds.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.4
• /
• pp.1233-1238
• /
• 2010

The lighting industry has become the bigger and more systemized using the semiconductor LED with each control R(Red), G(Green), B(Blue). The communication standard DMX512(ANSI E1.11) protocol of it basically needs the address which can be distinguished between the lighting terminals. The conventional method has to give the address of the lighting any methods like dip switch, EEROM and PROM. Then the lighting terminal can receive RGB data from DMX512 communication. According to electrical characteristics DMX512 protocol has to the splitter every 32 lighting terminals. If 512 lightings is all connected, maximum 16 splitters are needed. This paper is solved above weakness in DMX512 protocol using serial connection all lighting terminals. Also I developed the intelligent lighting terminal with auto-addressing. This was solved the inconvenience of the address assignment and the usage of the splitter. The developed products is applied and selled the semiconductor lighting terminals using ON-OFF control, dimming control, sequential control and rainbow control.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.9 no.4
• /
• pp.792-797
• /
• 2005

Lighting control switches based on the power line communication technology are developed and extended to incorporate dimming control to provide energy saving and appropriate illumination. The developed switch uses a general purpose microprocessor and associated electronics. Both the power line communication and the dimming function are implemented in one microprocessor, and it enables the low price commercialization. The frequency of the carrier was set at 250kHz considering the transmission data length and signal attenuation in power lines. Tests on prototypes in an low-voltage power lines have shown that the switches have a robust operation characteristics with the length of power lines and the variation of load capacities.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.13 no.4
• /
• pp.47-53
• /
• 2013

Nowadays, Advanced country have devised a plan energy-saving through lighting effectiveness and increasing performance of lighting control system. If it uses the LED as a source of light then conserve electricity by 50%. This paper implement LEMS(Lighting Energy Management System) that applicate and Smart Dimmer and Smart Switch that control the digital LED light, support wired-wireless communication using USN(Ubiquitous Sensor Network). This system of validity and reliability control special purpose lamp including indoor and outdoor lighting and landscape lighting effectively. It minimize the use of indoor and outdoor lighting energy by USN remote integral control function of Digital System Lighting of LED and increase effectiveness of energy and is a collaborative system that can feedback the use of electricity by measurement itself through Web and Switch.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.5
• /
• pp.1198-1206
• /
• 2011

In this paper, we proposed a home network integrated dimmer switch using Z-wave Mesh Network. The dimmer switch come with wired and wireless network-based intelligent lighting switch that can be installed in a apartments with home network technologies. This switch is ease to install and operate. Furthermore, it provide power saving through efficient control of light using motion detect sensor and light intensity sensor. In order to evaluate the performance of our developed home network integrated dimmer switch, we performed a load performance test and from our result, it showed excellent performance in terms of lighting control and communication speed.

• Proceedings of the KIEE Conference
• /
• 2002.11c
• /
• pp.317-320
• /
• 2002

In this thesis, we designed specific LonWorks nodes for lighting control then implemented the lighting control system through the operating scenarios. Developed lighting controller plays a role of one network node and according to information from other nodes, decides whether it toms on the light or not. In this way the lights can be controlled by using the location information of light in the lighting control node and the grouping information of the lights in the switch node.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• v.9 no.1
• /
• pp.281-284
• /
• 2005

A lighting control switch, extended to incorporate a power line communication technology, is developed. The system uses not an exclusive microprocessor but a general one, and developed PPM protocol. The coupling circuit is a type of an isolation LC filter, and the impedance of the circuit was designed as low as possible to extend signal transmission distance. The frequency of the carrier, considering the data length and signal attenuation as the length of power lines, was set at 250 kHz. Tests on a prototype in an indoor power lines have shown that the switch has a stable operation with the distance of power lines

• Journal of Navigation and Port Research
• /
• v.47 no.2
• /
• pp.85-92
• /
• 2023

The hardware of an LED lighting control system for coastal lighting at coastal pier entrance consists of a power supply unit, an AVR control unit, a CLCD output unit, an LED control unit, a scenario selection switch unit, and an operation speed display unit. It is made of an 8-channel. The CPU used ATmega128 and the FET was used to control the current signal. To operate the CPU, DC 12V was converted to DC 5V using a regulator 7805. A heat sink was used to remove heat generated in the FET. By connecting the load LED module to the manufactured 8-channel LED lighting control system, the operation was confirmed through various production scenarios. In addition, a control system was designed to show the most suitable color for the atmosphere of the coastal pier according to the input value of temperature and illumination using a fuzzy control system. Computer simulation was then conducted. Results confirmed that fuzzy control did not need to store many data inputs due to characteristics of artificial intelligence and that it could efficiently represent many output values with simple fuzzy rules.

• Journal of Power Electronics
• /
• v.16 no.4
• /
• pp.1268-1276
• /
• 2016

A triode for alternating current (TRIAC) dimming light emitting diode (LED) driver, which adopts a variable switched capacitor for LED dimming and LED power regulation, is proposed in this paper. The proposed LED driver is power efficient, reliable, and long lasting because of the TRIAC switch that serves as its main switch. Similar to previous TRIAC dimmers for lamps, turn-on timing of a TRIAC switch can be controlled by a volume resistor, which modulates the equivalent capacitance of the proposed variable switched capacitor. Thus, LED power regulation against source voltage variation and LED dimming control can be achieved by the proposed LED driver while meeting the global standards for power factor (PF) and total harmonic distortion (THD). The long life and high power efficiency of the proposed LED driver make it appropriate for industrial lighting applications, such as those for streets, factories, parking garages, and emergency stairs. The detailed analysis of the proposed LED driver and its design procedure are presented in this paper. A prototype of 80 W was fabricated and verified by experiments, which showed that the efficiency, PF, and THD at V_s = 220 V are 93.8%, 0.95, and 22.5%, respectively; 65 W of LED dimming control was achieved with the volume resistor, and the LED power variation was well mitigated below 3.75% for 190 V < V_s < 250 V.