• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2010년도 춘계학술대회 논문집
• /
• pp.470-474
• /
• 2010

Up until now, power centralized trains have been produced due to the maintenance convenience and comfortableness, but there are some problems, such as limitation of viscosity and maintenance difficulty of railroad due to recently increasing axle mass. In order to improve the problems, power decentralized trains have been developed to improve traction power. In the case of using electrical braking system, it is possible to improve braking friction power. Induction motors have been developed for power decentralized high speed train because of less structural defection, and low maintenance and production cost. However, induction motors have limitations, such as assuring enough power capacity and efficiency with reduced size. PMSM (Permanent magnet synchronous motor) have been newly developed to improve shortcomings of induction motors. The PMSM can be produced small and light weighted. Also if the PMSM and induction motors have the same size and power capacity, the PMSM have better power efficiency. In this pater, the prototype and modified type of PMSM for "High-speed Electric Multiple Unit-400km/h eXperimmen" will be introduced.

• 대한전기학회논문지
• /
• 제39권11호
• /
• pp.1174-1182
• /
• 1990

A hgih efficiency and good dynamic performance drive system of an induction motor is presented in this paper using vector control technique. If the induction motor is driven under light loads with rated flux, the iron loss is excessively large compared with the copper loss, resulting in poor motor efficiency. High efficiency drive of an induction motor can be achieved by adjusting the flux level which leads the total motor loss to be a minimum value. Generally reducing the flux degrades the dynamic performance, but the dynamic performance of the proposed system is also maintained high. If the d-axis is coincident with rotor flux phasor in synchronous rotating reference frame, the stator current can be decoupled as flux component and torque component. At steady state, the developed motor torque is proportional to the product of the flux and torque component. The combination of the two components minimizing the motor loss could be found with numerical method. As the procedure to obtain the optimal combination is too hard, it is found experimentally. The system block diagram is suggested for maximum efficiency control. The proposed system is studied through digital simulation and verified with experiment. The experimental results show the possiblity of a high efficiency drive with good dynamic performance of maximum efficiency control.

• 전기의세계
• /
• 제16권2호
• /
• pp.1-8
• /
• 1967

From the discovery of Alago's disk, a number of trials and efforts have been concentrated on a small-sized and light-weighted induction motor. They have devoted themseleves, however, mainly to a improvement of cooling effect, a proper weight-distribution of copper and iron and desirable number of slots. In consequence, such an effort restricted only to the field of design, has resulted in unsatisfactory developments in the insulating materials consisting of the main parts of an induction motor. The quality of fibre and paper which are used as class-A insulation materials with their "compound" and "varnish" has been increased to some extent. Similarly Class-B insulation materials like asbest mica has been almost a combination of inorganic and binding materials. But nowadays synthesic chemistry is making a remarkable progress. So it comes possible for us to have silicon resin and other good ones of similar charateristics. And even a thin silicon resin insures us to get excellent heat-pro f and insulation, so a better space factor and cost-down in motor design have come possible in most advanced nations of the world, but not in our country. Furthermore, a consideration of productivity and economy in manufacturing process has been neglected by a majority of engineers. This is more unpleasant und more undesirable. I think this rational method of induction motor design using new synthesic resin will devote in making your productivity and economy better. And the nation-wide standard value of electric motor size is sited here. size is sited here.

• 한국환경성돌연변이발암원학회지
• /
• 제26권4호
• /
• pp.97-112
• /
• 2006

Heme oxygenase(HO)-1 is an important antioxidant enzyme that plays a pivotal role in cellular adaptation and protection in response to a wide array of noxious stimuli. Thus, HO-1 induction has been associated with prevention or mitigation of pathogenesis of various diseases, including acute inflammation, atherosclerosis, degenerative diseases, and carcinogenesis. Recent progress in our understanding of the function of molecules in the cellular signaling network as key modulators of gene transcription sheds light on the molecular mechanisms underlyuing HO-1 gene expression. A panel of redox-sensitive transcription factors such as activator protein-1, nuclear factor-kB, and nuclear factor E2-related factor-2, and some of the upstream kinases have been identified as prime regulators of HO-1 gene induction. This review summarizes molecular mechanisms underlying HO-1 expression and the significance of targeted induction of HO-1 as a potential chemopreventive or chemoprotective strategy.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1993년도 하계학술대회 논문집 B
• /
• pp.908-911
• /
• 1993

The single-Phase induction motor is widely used in many light duty applications. especially in home and the office. At present, many applications which use these motor require continuously adjustable speed control. In the general, the speed control of single-phase induction motor is accomplished at a few discrete speeds by using tapped-windings, pole switching or gear. These techniques is inefficient and complicated. In this paper, auxiliary winding voltage phase angle of single-phase induction motor is used to continuously adjust electromagnetic torque. The analysis includes the determination of the relationship between the auauxiliary winding voltage phase angle and torque. Simulation results of the motor's torque-speed characteristics using the controlled auxiliary winding supply are shown and discussed. The drive is tested using a dynamometer to experimentally verify the results of the theory and simulations.

• 한국약용작물학회지
• /
• 제3권3호
• /
• pp.233-239
• /
• 1995

산채막(山菜莫)(Cornus officinalis Sieb. et Zucc. )의 조직배양(組織培養)을 위한 기초적(基礎的) 연구(硏究)로서 체배양(諦培養)에 미치는 배지(培地), 생장조절제(生長調節劑), 저온(低溫) 전처리(前處理), 배양온도(培養溫度) 및 광(光)의 영향(影響)을 검토(檢討)한 결과(結果)는 다음과 같다. 1. 캘러스 형성율(形成率)은 MS배지(培地)보다 WPM배지(培地)에서 좋은 반응(反應)을 보였으며, Img/L NAA를 첨가(添加)한 WPM배지(培地)에서 54%로 가장 높았고, 캘러스 생장(生長)은 2mg/L NAA를 첨가(添加)한 MS배지(培地)에서 좋았다. 2. 약(約)의 배양온도(培養溫度) 및 광(光)의 영향(影響)은 $25^{\circ}C$, 16시간 명배양(明培養)이 62%의 가장 높은 캘러스 형성율(形成率)을 보였다. 3. 캘러스 형성(形成)에 미치는 약(約)의 저온(低溫) 전처리(前處理) 효과(效果)는 $4^{\circ}C$, 36시간 처리(處理)에서 19.5%로 가장 높았다. 4. 기관분화(器官分化)를 위한 적정배지(適正培地)로는 0. 5mg/L 2, 4-D와 1mg/L kinetin을 첨가(添加)한 MS배지가 녹점형성(綠點形成) 및 뿌리분화를 촉진(促進)하였다. 5. 캘러스 양변화(楊變化) 방지(防止)를 위하여는 3-5mg/L ABA 와 5mg/L $AgNO_3$의 첨가(添加)가 효과적이었으며, 캘러스 활력(活力)이 높아 녹점형성(綠點形成)을 촉진(促進)하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 추계학술대회 논문집 광주전남지부
• /
• pp.81-86
• /
• 2006

In this paper, we designed the cylindrical type light source that had a electromagnetic principle of inductively coupled plasma, and measured its electrical-optical properties. Using the principle of transformer, electrically equivalent circuit of cylindrical type light source was analyzed. According to the parameters of electromagnetic induction which were diameter of coil with 0.3~1.2 mm, number of turns with 4~12 turns, distance with 40~120 mm and RF power with 10~150 W, the electrical and optical properties were measured. When diameter of coil was 0.3 mm, number of turns was 8 turns and distance was 40 mm, the highest brightness of 29,730 $cd/m^2$ was shown with RF power 150 W. The relationship between electromagnetic induction and plasma discharges was shown by mode transition from E-mode to H-mode.

• 식물조직배양학회지
• /
• 제27권3호
• /
• pp.203-211
• /
• 2000

흰독말풀의 tumor조직에서 유도한 tumor callus로부터 scopolamine의 생산을 극대화하기 위한 연구를 수행하였다. Tumor callus의 생장률을 증가시키기 위해서는 초기접종량을 배지의 2%로 하고 배양기간은 4주가 효과적이다. 그래서 만일 이단계배양을 추진하려면 배지교체의 시기는 3주가 가장 적당한 것으로 확인되었다. Scopolamine의 생성을 위한 광의 효과를 알아본 결과, 암상태보다 광상태가 callus생장 및 scopolamine 함량 증가에 효과적이었다. Scopolamine 함량 증가의 최적 광량은 16$\mu$mo1 m$^{-2}$ s$^{-1}$, 광질은 적색파장 그리고 연속광보다 장일조건 (16/8)의 광주기에서 tropane alkaoid인 scopolamine합성이 현저히 촉진되었다. 질소원으로는 산화형 질소인 NO$_{3}$$^{-}$ 를 4 g/L로 증가시키는 것이 가장 효과적인 것으로 확인되었다. Scopolamine의 함량을 증가시키기 위한 elicitor 공급은 10 mg/L chitosan과 15 mg/L yeast추출물이 가장 효과적이었으며, 전구물질로는 0.2 mM tropine과 0.3 mM tropic acid가 가장 우수한 것으로 확인되었다. 이러한 결과를 종합해 보면, 흰독말풀 tumor callus에서 scopolamine 대량생산을 추진할 경우 3주 동안 광상태와 무기이온 조성을 균형 있게 조절하여 생장을 최대로 증가시킨 후, 1주 동안 scopolamine생산을 위해 elicitor, precursors 등이 조합된 배지에서 biotransformation 시키는 것이 가장 효과적일 것으로 판단된다. 또한 tumor callus에 $^{60}$Co${\gamma}$-ray을 조사하여 3K, 4K및 6k tumorcallus를 확보하였으며, 이들로부터 유도한 teratoma는 형태적 변이를 나타내었다. Teratoma로부터 또 다시 새로운 teratoma-callus 세포주를 유도하여 현탁배양을 수행하였던 바, MS 기본 배지에서 1.0 mg/L 2.4-D과 0.5 mg/L kinetin을 조합하여 처리한 callus 의 액체배양에서 cell aggregation이 일어나지 않고 세포가 유리화 되면서 왕성한 생장을 보였다.

• Journal of Plant Biotechnology
• /
• 제39권3호
• /
• pp.205-211
• /
• 2012

Pueraria lobata is a perennial legume plant, widely distributed in the countries of East Asia. It is a medicinally important leguminous plant and produces various isoflavones such as puerarin, daidzein etc which have potential for preventing several chronic diseases including osteoporosis, cardiovascular disease and cancer. In this study, we tried to induce hairy roots in vitro from Korean wild arrowroot P. lobata and investigated the effects of hormones and light conditions. Initially leaf and stem segments were infected with Agrobacterium rhizogenes and incubated in different conditions. Hairy roots were induced from only stem segments and the induction was best at dark condition and the presence of IBA during incubation. Secondary roots were also significantly much more induced at the dark condition than at the 16 hours light condition. Among plant growth regulators of auxin, IBA was best for secondary root formation while 2,4-D, IAA and NAA produced callus or less hairy roots. The presence of the foreign gene rolC transferred by A. rhizogenes that plays a major role in hairy root induction was confirmed by PCR. The accumulation of isoflavones such as puerarin and daidzin was also confirmed. These results will facilitate mass production of hairy root and can be used for the production of functional substances from wild arrowroots.

• 한국지반신소재학회논문집
• /
• 제2권3호
• /
• pp.19-24
• /
• 2003

폐기물 매립지 바닥층 및 사면에 적용되는 평편 형 및 텍스츄어드 형 고밀도 폴리에틸렌 지오멤브레인의 장기성능이 검토되었다. 특수 설계된 스크래치 장치를 이용하여 인위적으로 지오멤브레인 표면에 결함을 부여하였다. 결함 및 미결함 지오멤브레인의 역학적 및 마찰특성, 화학저항성 및 자외선 저항성 그리고 산화유도시간 등이 검토되었다. 텍스츄어드 형 지오멤브레인의 마찰특성이 평편 형 지오멤브레인 보다 우수함을 알 수 있었다. 끝으로 화학저항성, 자외선 저항성 그리고 산화유도시간 측정결과로부터 결함이 없는 지오멤브레인과 텍스츄어드 형 지오멤브레인의 장기성능이 결함이 있는 지오멤브레인보다 우수함을 알 수 있었다.