• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1995.05a
• /
• pp.47-49
• /
• 1995

We report the spectroscopic properties of column-III nitrifies of GaN, GaInN, and AlGaN. The column-III nitride semiconductors are promising materials to realize the current-injection-type blue-and ultraviolet (UV)-light-emitting devices with high performance. To acheive the lasing with low threshold, the devices are must constructed to double heterostructure by succesive epitaxial growth technique, and we must confine the carriers in the potential barrier and optical confinement in wave guide between barrier and active layers has different refractive index. The refractive index of column-III nitride semiconductors, however, are rarely reported. The measured refractive index was 2.9, and the observed characteristic peak near the enrgy gap was analysed using a dielectric function and may due to excitonic contribution.

• Transactions of Materials Processing
• /
• v.22 no.1
• /
• pp.48-53
• /
• 2013

As the adoption of injection molding technology increases, injected-molded optical products require higher dimensional accuracy and optical stability than ever before. In the present study, four kinds of molding methods, i.e., conventional injection molding (CIM), injection/compression molding (ICM), rapid heat and cooling the mold(RHCM) and rapid injection/compression molding (RICM) were selected in order to investigate the optical anisotropy of a 7 inch Light Guide Plate(LGP) by examining the gap-wise distribution of birefringence and the extinction angle. The results indicate that the compression process can decrease flow-induced birefringence over the whole region and that rapid heating can decrease the birefringence level better than conventional molding. In addition, for the combination of compression and rapid heating a reversal flow was detected from the distribution of the extinction angle near the gate.

• Transactions of Materials Processing
• /
• v.20 no.1
• /
• pp.5-10
• /
• 2011

The main objective of the present study is to predict the process window of injection-compression molding corresponding to the capability of an injection machine for fabricating 7 inch LGP. The open distance and volume filled after injection stage were found to be two important factors that affect critical requirements such as flow length, injection pressure and clamping force for the process. Process window for the key factors was also predicted by response surface method. As a result, predicted process window for open distance and volume filled after injection stage satisfying the critical requirement with a given injection machine was in the range of 60 ~ 75%, and 104.00 ~ 104.25%, respectively.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.8
• /
• pp.157-163
• /
• 2001

This paper presents the new linear notion device so called \"inch-werm\" which gets large displacement by incrementally summing small displacements of PZT actuators. Dynamic stiffness of inch-worm is generally low compared to its driving condition due to the requirement of inch-worm like small size and light weight. This low stiffness may degenerate the positional precision of inch-worm. An inch-worm is realized using three PZT actuators, a monolithic moving device and a guide way frame. Finite element method and experimental approach are used to analyse the static and dynamic motion of the designed inch-worm. Command reference input is shaped to reduce the residual vibration of inch-worm. The practical feasibility of inch-worm is also examined by running tests.ing tests.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1469-1474
• /
• 2007

In recent years, research to machine large-surface micro-features has become important because of the light guide panel of a large-scale liquid crystal display and the bipolar plate of a high-capacity proton exchange membrane fuel cell. In this study, in order to realize the systematic design technology and performance improvements of an ultra-precision machine for machining the large-surface micro-features, a structural characteristic analysis was performed using its virtual prototype. The prototype consisted of gantry-type frame, hydrostatic feed mechanisms, linear motors, brushless DC servo motor, counterbalance mechanism, and so on. The loop stiffness was estimated from the relative displacement between the tool post and C-axis table, which was caused by a cutting force. Especially, the causes of structural stiffness deterioration were identified through the structural deformation analysis of sub-models.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.2 s.95
• /
• pp.74-81
• /
• 1999

The integrated chip of optical micro-encoder was fabricated and the feasibility as displacement measurement device was confirmed. The geometry of micro-encoder was designed to utilize the optical interference effect on the second order of diffracted beams. The hybrid-type micro-encoder consisted with light emitting diode, photodiode, polyimide wave-guide and micro-lens provides stable micro-encoding results for high speed displacements. The measurement shows the resolution of displacement of 1.00 +/- 0.02 ${\mu}m$ for the grating with scale pitch of 2.0${\mu}m$.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11b
• /
• pp.486-491
• /
• 2002

Auditory experiments based on subjective responses were undertaken for the standard heavy and light weight impact noise. Relations between noise levels and subjective evaluations were also investigated. As a result, it was shown that the noise class was rated with the range of sensible satisfaction by investigating the various social responses for the floor impact noise. The rate classification for the heavy weight impact noise is suggested as a design guide for concrete slabs which satisfy the residents' requirements in various sound insulation capacities of multistory residential buildings.

• Transactions of Materials Processing
• /
• v.15 no.1 s.82
• /
• pp.27-33
• /
• 2006

It is necessary to improve the pattern replication and birefringence in LGP(Light guide panel) for better optical performance. In the present paper, the effects of injection-compression and injection-press mode with normal injection mold on the distribution of transcription of pattern and birefringence were studied. It was found that the values of pattern replication was improved and the birefringence was reduced for the cases of low initial clamping force in injection-compression mode and for the cases of longer mold opening length in injection-press mode, repectively.

• Transactions of Materials Processing
• /
• v.15 no.1 s.82
• /
• pp.71-75
• /
• 2006

In recent, various shapes of pattern in micron or nano scale are adapted in many applications due to their good mechanical or optical properties. Light guide panel (LGP) of the LCD is one of important applications for micro pattern and micro prism shape is one of the typical patterns. The size of the surface patterns in most applications is decreasing to the order of micron or even under micron. On the other hand, the area to be patterned keeps enlarging. These two trends in patterned products require tooling micro patterns on large surface, which has still many technical problems to be solved mainly due to pattern size and the tooling area. In this study, we fabricated prism shape of patterns using diamond cutting tool on some metal core and plastic core like PMMA. Some cutting conditions were investigated including cutting force, cutting depth and speed for different core materials.

• Transactions of Materials Processing
• /
• v.15 no.9 s.90
• /
• pp.686-691
• /
• 2006

Powder blasting technique was introduced to micromachine the micro patterns of circular and rectangular shape in LGP mould. The machinability of these patterns and matt treatment by powder blasting were verified. Then a prototype of LGP was injected by the developed LGP mould with micro patterns. Shape analysis of micro patterns and performance test of the injected LGP were carried out. The results showed printless LGP with micro patterns could be produced by just single injection using the mould with micro patterns, and powder blasting technique could be successfully applied to micrornachining of micro patterns and matt treatment of LGP mould.