• Nuclear Engineering and Technology
• /
• 제29권6호
• /
• pp.468-475
• /
• 1997

The transient photocurrent in amorphous silicon radiation detectors (n-i-n and forward biased p-i-n) were analyzed. The transient photocurrents in these devices could be modeled using multiple trap levels in the forbidden gap. Using this model the rise and decay shapes of the photocurrents could be fitted. The decaying photocurrent shapes of the p-i-n and n-i-n devices after a short duration of light pulse showed a similar behavior at low dark current density levels, but at higher dark current density levels the photocurrent of the p-i-n diode decayed faster than that of the n-i-n, which could be explained by the decreased electron lifetimes in the forward biased p-i-n diode at high dark current densities. The transient photoconductive gain behaviors in the amorphous silicon radiation detectors are discussed in terms of device configuration, dark current density and time scale.

• 대한기계학회논문집B
• /
• 제33권8호
• /
• pp.589-595
• /
• 2009

The instability wave formed near nozzle region grows to vortex with large scale in downstream region of spray. It plays an important role in the fuel-air mixing, combustion process and engine exhaust emissions in direct injection diesel engine. The objective of this study is to analyze effect of variant parameters (injection pressure, ambient gas density, etc.) and fuel properties on spray instability near nozzle region. Spray structure near nozzle region was investigated using a magnification photograph. A pulsed Nd-YAG laser was used as a light source, and image was taken by CCD camera. The following conclusions are drawn from this experimental analysis. In low ambient density, the effect of fuel properties on spray instability near nozzle region is dominant. In high ambient density, the effect of ambient gas on spray instability near nozzle region is dominant. High jet velocity has strong influence on spray instability.

• 한국세라믹학회지
• /
• 제21권2호
• /
• pp.156-164
• /
• 1984

The characteristic of pyrolytic carbon deposited in a fluidized bed as measured by density apparent crystallite size and viewed metallographically under polarized light can be easily controlled by adjusting the deposition parameters such as deposition temperature and propane flow rate or silicon content. The density of isotopic pyrolytic carbons deposited from propane between 120$0^{\circ}C$ and 140$0^{\circ}C$ increases with increasing propane flow rate and decreasing deposition temperature from 1, 73g/cc to 2.08g/cc. The apparent crystallite size Lc parameter appears to depend only on deposition temperature being entirely independent of the propane flow rate. The carbon matrix density of the silicon-alloyed carbonds deposited from propane and methyltrichlorosil-ane from 2.05g/cc for a silicon content around 9wt% to 2.67g/cc for a silicon content of 36.7wt% The Lc parameter of the deposition temperature being entirely independent of the silicon content.

• 한국세라믹학회지
• /
• 제52권2호
• /
• pp.159-164
• /
• 2015

We manufacture artificial lightweight aggregates (ALWAs) using bottom-ash as the primary raw material. We coat the ALWA surfaces with low-melting point materials in order to enable them to bloat, which is essential to reduce the bulk density of the aggregate. Then, we sinter the prepared aggregates at 1000, 1100, and $1200^{\circ}C$ using either the direct or two-step firing schedules. Finally, we evaluate the properties of the fired samples through analyzing their bulk density, water absorption, and microstructure. The surface-modified samples result in a reduction of their bulk density by $0.3{\sim}0.4g/cm^3$ regardless of the firing method used. Based on these results, we conclude that this approach could provide a viable method for the mass-production of ALWAs from industrial waste such as bottom-ash.

• 한국의류학회지
• /
• 제21권3호
• /
• pp.600-606
• /
• 1997

The dyeing with loess has been studied. Two kinds of cotton fabrics having different thickness and density were dyed in loess paste bath. The color differences of the fabrics which were dyed repeatedly.five times were not significant. The dyeing of cotton fabrics with loess was not exactly reproducible, but dyeability of the cotton fabrics of high density was better than that of low density. Loess on the dye6 fabrics was physically jammed between the fibers in the form of the fine particles. The cotton fabrics dyed with loess have good light fastness, but their laundering fastness and abrasion fastness were not good. An aftertreatment was carried out by using the extracted solution from acorn or persimon, and FeSO4 lot improving fastness. When the dyed fabrics was after-treated with FeSO4, the laundering fastness and wet abrasion fastness were improved extremely.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 1998년도 제14회 학술발표회 논문개요집
• /
• pp.17-17
• /
• 1998

Synchrotron radiation is produced when charged particles moving with relativistic velocities a are accelerated - for example, deflected by the bending magnets which guide the electron or p positrons in circular accelerators or storage rings. By using special focusing magnetic lattices i in the particle accelerators it is possible to make the dimensions of the particle beam very small with a hi맹 charge density which results in a light source with high b디lIiance. Synchrotron light h has important properties which make it ideal for a wide range of investigations in surface s science. The fact that the spectrum of electromagnetic radiation emitted in a bending magnet e extends in a continuum from the 얹r infra red region to hard x-rays means that it is id않I for a v variety of spectroscopic studies. Since there are no convenient lasers, or other really bright l light sources, in the vacuum ultraviolet and soft x-ray re.밍ons the development of synchrotron r radiation has enabled enormous advances to be made in this di펌C비t spectr따 re밍on. P Polarization-dependent measurements, for ex없nple ellipsometry or circular dichroism studies a are possible because the radiation has a well-defined polarization - linear in the plane of orbit w with additional right-circular, or left-circular, components for emission an생es above, or below, t the horizontal, respectively. Since the synchrotron light is emitted from a bunch of charge c circulating in a ring the light is emitted with a well-defined time structure with a short flash of l light every time a bunch passes an exit port. The time structure depends on the size of the ring a and the number and sequence of filling of the bunches. A pulsed light source enables time¬r resolved studies to be performed which provide direct information on the lifetimes and decay m modes of excited states and in addition opens up the possibility of using time of flight t techniques for spectroscopic studies. The fact that synchrotron radiation is produced in a clean u ultrahi야 vacuum environment is of gr않t importance for surce science studies. The current t비rd generation synchrotron light sources provide exceptionally high baliance and stability a and open up possibilities for experiments which would have been inconceivable only a short time ago.

• 대한기계학회논문집B
• /
• 제24권1호
• /
• pp.93-101
• /
• 2000

The characteristics of spray nozzle have been quantified with the measurement of fluorescence and Mie scattering images. To correct the attenuation of the incident light sheet, a sequential double-pass light sheet system and the geometrical averaging of two images was implemented. Quantitative mass flux distribution of spray was obtained from fluorescence image. 3-D image is reconstructed using 2-D radial images. Sauter mean diameter (SMD) distribution was determined using the ratio of fluorescence signal intensity and Mie scattering signal intensity and the values were quantified with PDP A data. The measurement of mass flux and SMD using planar imaging technique agee with PDP A data fairly well in the low density region. However, in dense region， there are significant errors caused by secondary scattering. It was found that the planar imaging technique provides many advantages over the point measurement technique, such as PDP A, and can be implemented for quantitative measurement, especially in low density region.

• 전기학회논문지
• /
• 제62권7호
• /
• pp.1038-1044
• /
• 2013

A research on thermal analysis method is conducted for the characterization of heat generation during operation of Interior Permanent Magnet Synchronous Motor(IPMSM) for Light Railway Transits(LRT) in this paper. Efficient cooling of the heat generated in the IPMSM is important because the excessive heat generated from the winding, core and permanent magnet makes it harder for a long time continuous operation of IPMSM. Therefore, in order to analyze the heat generation characteristics of the 110kW-class IPMSM as advanced research for application the IPMSM to the cooling device, the heat transfer coefficients for each component of the 110 kW-class IPMSM were derived and the thermal equivalent network was configured to perform the thermal analysis in this study. Finally, the 110kW-class IPMSM prototype is made and a comparative verification between the test data and the thermal analysis results through its various performance tests are carried out.

• 한국광학회지
• /
• 제6권1호
• /
• pp.50-55
• /
• 1995

Ar이온빔의 보조 증착법으로 soda-lime유리판에 증착한 Cr박막을 브릴루앙 산란 실험을 통하여 박막의 탄성특성을 조사하였다. 박막증착시 사용된 이온의 전류 밀도가 증가할 수록 박막의 탄성계수가 증가하였으며 박막의 탄성특성이 bulk의 특성에 근접하였다. $400\muA/cm^{2}$의 이온전류밀도의 이온빔의 보조 증착으로 제작된 Cr박막의 탄성계수는 $c_{11}=296, c_{13}=83, c_{33}=289$, 그리고 $c_{55}=c_{44}=108(\times10^9/N/m^{2}}$이 었으며 이는 bulk의 값들에 비해 5% 감소한 것이다.

• 한국분말재료학회지
• /
• 제13권2호
• /
• pp.102-107
• /
• 2006

Recycling industrial wastes such as fly ash from a coal burning heat power plant and shell from an oyster farming were investigated to prevent environment contamination as well as to enhance the value of recycling materials. In this study, the lightweight aggregates and the red bricks were fabricated from fly ashes with other inorganic materials and wastes. The starting materials of the lightweight aggregate were fly ash powder and water glass, and the compacts of these materials were heat treated at $1100^{\circ}C$. The fabricated lightweight aggregates had low bulk density, $0.9-1.2\;g/cm^3$, hence floated on the water and had the strength of 7.0-11.0 MPa and the modulus of 2900-3300 MPa which indicates it has enough strength as the aggregate. Another type of the light weight aggregate was prepared from fly ashes, shell powders and clays. The bulk density, porosity, and compressive strength of these aggregates were $1.19-1.34\;g/cm^3,\;18.3{\sim}56.1%$ and 5-12 MPa, respectively. The addition of a small amount of fly ash powder prevented hydration of the light weight aggregates. The red brick was also fabricated from the fly ash containing materials. It is suitable for the brick facing of a building as it has moderate strength and low water absorption rate.