• 한국전자파학회논문지
• /
• 제7권2호
• /
• pp.95-104
• /
• 1996

임의의 평면파가 각진 두 도선에 입사시 관계변수들이 양단부하에 유기되는 전압에 미치는 영향을 조사하였다. 전송선 양단의 임피던스가 정합되고 입사파의 방향이 방위각과 고도각이 같을 때 유기전압이 최소가 됨을 알 수 있었다. 또한, 도선의 반경이나 도선간의 경사각이 변할 때 도표상에서 유기전압을 계산할 수 있는 방안도 제시하였다.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2010년 춘계학술대회논문집
• /
• pp.109-114
• /
• 2010

Interface tracking of two phase is significant to analyze multi-phase phenomena. The VOF(Volume of Fluid) and level set are well known interface tracking method. However, they have limitations to solve compressible flow and incompressible flow at the same time. CIP(Cubic Interpolate Propagation) method is appropriate for considering compressible and incompressible flow at once by solving the governing equation which is divided up into advection and non-advection term. In this article, we analyze the droplet impingement according to various We number using improved CIP method which treats nonlinear term once more comparison with original CIP method. Furthermore, we compare spread radius after droplet impingement on the wall with the experimental data and original CIP original CIP method, and it reduces the mass conservation error which is generated in the numerical analysis comparison with original CIP method.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.1088-1091
• /
• 1997

This paper describes the characteristic of hinges on which a lever pivots within a limited angle due to the torque. The hinges are exerted by the thermally expanded actuators connected with a level through hinges. To enhance the stroke of inchworm actuator, FEM(Finite Element Method) was utilized for the characterization in view of stress displacement according to the variation of notch radius and notch width. As a result, notch width of the hinges plays an important part in improvement of micro inchworm actuator.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제12권10호
• /
• pp.4774-4796
• /
• 2018

Wireless sensor networks are composed of a large number of inexpensive and tiny sensors used in different areas including military, industry, agriculture, space, and environment. Fault tolerance, which is considered a challenging task in these networks, is defined as the ability of the system to offer an appropriate level of functionality in the event of failures. The present study proposed an intelligent throughput descent and distributed energy-efficient mechanism in order to improve fault tolerance of the system against soft and permanent faults. This mechanism includes determining the intelligent neighborhood radius threshold, the intelligent neighborhood nodes number threshold, customizing the base paper algorithm for distributed systems, redefining the base paper scenarios for failure detection procedure to predict network behavior when running into soft and permanent faults, and some cases have been described for handling failure exception procedures. The experimental results from simulation indicate that the proposed mechanism was able to improve network throughput, fault detection accuracy, reliability, and network lifetime with respect to the base paper.

• 한국정밀공학회지
• /
• 제28권8호
• /
• pp.942-950
• /
• 2011

Automation is important in modern agricultural environment, which demands the highest level of technology. In the paper an independent four-wheel steering driving platform is developed especially for horticulture in glass house farm. Mathematical modeling of the four wheel system is carried out for smooth movement. The relationships between steering angle, the turning radius, and escape trajectory are simulated using the dynamic analysis program. Optimal driving algorithm is sought through the performance evaluation.

• 한국운동역학회지
• /
• 제30권3호
• /
• pp.205-215
• /
• 2020

Objective: The purpose of this study was to investigate the relative angles and cross-correlation between body segments and ski among four alpine ski turning techniques. Method: 19 alpine ski instructors participated in this study. Each skier asked to perform 4- types of turning technique, classified by radius and level. 8 inertial measurement units were used to measure orientation angle of segment and ski on the anteroposterior and vertical axis. Results: Significant differences were found between types of turning in the segments-ski relative angle on the anteroposterior and vertical axis (p<.05). Although, cross-correlation showed a high correlation between angles of segment and ski, there were significant differences between types of turning. Conclusion: Based on our results, the relative movement and timing between each segment and ski is different according to the turning techniques, so the training methods should be applied differently.

• 한국대기환경학회지
• /
• 제6권1호
• /
• pp.51-56
• /
• 1990

This Study shows the effect of the district heating on the $SO_2$ concentration reduction. In order to analyze the effect of the district heating, three alternatives were set up as follows; Alternative I represented present central heating system, and Alternative II and Alternative III represented district heating system of which the scale were different from. The concludions of this study are as follows; In case of the Alternative II and III, annual average $SO_2$ concentration are reduced by 9.0% and 14.6% respectively, and winter season $SO_2$ concentrations are reduced by 12.2% and 15.8% respectively, at the highest points. The average reduction rates of $SO_2$ concentration in the district heating area are about the same as the reduction rates at the highest points. Also, it was found that using the district heating system, the ground level $SO_2$ concentrations could be reduced within the area of 5 to 10 km radius.

• 소성∙가공
• /
• 제21권8호
• /
• pp.485-492
• /
• 2012

As the shape of stamped part is complicated and as the trend toward light weight continues, the higher level of difficulty is required in making stamping die because of inevitably poor formability. The poor formability can be improved if the material flow during the stamping is carefully controlled. Application of drawbead became commonsense used to retard metal flow of blank into the die cavity at the region where wrinkle is expected. In the study, the concept of beadless stamping process is proposed and the method how to realize the beadless stamping process is presented. The validity of the proposed method is confirmed by the application of the real auto part.

• 한국정밀공학회지
• /
• 제13권1호
• /
• pp.123-130
• /
• 1996

The procedure on the design of a new tungsten cabide throw-away cutting tool system for deep grooving or cut-off machining is suggested. For relieving the maximum stress level at the corner radius of the blade holder, the finite element method is used. Also the pulling test device is proposed for measuring the holding force of the insert between the blade holder and the insert considering the materials in contact and configuration parameters of the holder.

• 소성∙가공
• /
• 제20권6호
• /
• pp.456-460
• /
• 2011

A major source of difficulty in die design for high strength steel is the high level of elastic recovery during unloading. The degree of elastic recovery is affected by factors such as material strength, bending angle, punch's corner radius and sheet thickness. Finite Element Method was used in the present work to quantitatively analyze the elastic recovery for various combinations of these parameters. In some cases elastic recovery happened in reverse direction. This phenomenon, which we call spring-go, was explained via changes in stress distribution in the panel occurring in the forming process.