• Magazine of the Korean Society of Agricultural Engineers
• /
• v.44 no.4
• /
• pp.129-138
• /
• 2002

This paper presents a study on the discharge capacity of geotextiles as a horizontal drain layer placed between the layers of earth fill and natural soft ground. Required discharge capacity of geotextiles as drain layers estimated by consolidation analysis is proportional to the consolidation coefficient of the ground soils and the width of the earth fills. The field discharge capacity of the geotextiles are measured by the hydraulic transmissivity test. And the results show wide variation according to the material characteristics of geotextiles, water content of the soils, vertical pressure, and etc. For the short horizontal drain length, geotextile filter mat can be used for the horizontal drain layer. And f3r the long drain($25{\sim}55m$), it is used for the drain together with Bord Drain.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.14 no.6
• /
• pp.61-67
• /
• 2005

During stereolithography processes, one of the main sources of dimensional error of prototype is the distortion effect owing to the shrinkage of resin. In this study, the effects of dimension of specimen, such as length, width, and thickness, on the curl distortion is examined. During the SL processes, the variation of curl distortion ewer is measured according to the number of layers, Through this study, it is verified that there is a big difference of the distortion error in both direction and magnitude between before and after the supports are removed. It Is also observed that end profile of the test part and the upper side around the border are also distorted due to the shrinkage of the resin.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.25 no.5
• /
• pp.61-66
• /
• 2011

An accidental disconnection of power supply for operating theatres may result in fatal accidents. Thus, it is necessary to import the electric safety system in medical locations. This paper shows an analysis of simulation for the safety in medical IT system based on KS C IEC 60364-7-710(Electrical Installations of Buildings - Requirements for special installations or locations - Medical locations). The analysis was progressed by measuring leakage currents according to variation of volts, circuits and loads. And it was made database for calculation the reasonable length of branch circuit.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.4
• /
• pp.99-105
• /
• 2002

The performance test of an axial-type turbine is carried out with various axial gap distances between the stator and rotor. The turbine is operated at the low pressure and speed, and the degree of reaction is 0.373 at the mean radius. The axial-type turbine consists of ons-stage and 3-dimensional blades. The chord length of rotor is 28.2mm and mean diameter of turbine is 257.56mm. The power of turbo-blower for input power is 30kW and mass flow rate is $340m^3$/min at 290mmAq static-pressure. The RPM and output power are controlled by a dynamometer connected directly to the turbine shaft. The axial gap distances are changed from a quarter to three times of stator axial chord length, and performance curves are obtained with 9 different axial gaps. The efficiency varies about 8% of its peak value due to the variation of axial gap on the same non-dimensional mass flow rate and RPM, and experimental results show that the optimum axial gap is 1.6-1.9Cx.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.5
• /
• pp.2059-2066
• /
• 2018

This study explored the feasibility of utilizing an SWCNT-coated fabric sensor for the development of a wearable motion sensing device. The extent of variation in electric resistance of the sensor material was evaluated by varying the fiber composition of the SWCNT-coated base fabrics, attachment methods, number of layers, and sensor width and length. 32 sensors were fabricated by employing different combinations of these variables. Using a custom-built experimental jig, the amount of voltage change in a fabric sensor as a function of the length was measured as the fabric sensors underwent loading-unloading test with induced strains of 30 %, 40 %, and 50 % at a frequency of 0.5 Hz. First-step analysis revealed the following: characteristics of the strain-voltage curves of the fabric sensors confirmed that 14 out of 32 sensors were evaluated as more suitable for measuring human joint movement, as they yield stable resistance values under tension-release conditions; furthermore, significantly stable resistance values were observed at each level of strain. Secondly, we analyzed the averaged maximum, minimum, and standard deviations at various strain levels. From this analysis, it was determined that the two-layer sensor structure and welding attachment method contributed to the improvement of sensing accuracy.

• Journal of Welding and Joining
• /
• v.31 no.6
• /
• pp.90-95
• /
• 2013

Pipe inside clad welding is mainly used to the flow pipe of sub-sea or chemical plant. For the inside clad welding to the medium pipe with the diameter of about 12", TIG welding is frequently applied with filler metal. In this case, the clad welding has the very broad weld area over $10m^2$. And, the non-destructive test (NDT) such as ultrasonic test (UT) or radiographic testing (RT) should be conducted on the broad weld area, and it costs very high due to the time-consuming work. Therefore, the present study investigated the variation of arc voltage to develop the in-line quality monitoring system for the pipe inside TIG cladding. The 4 experimental parameters (current, arc length, wire feed position, and shield gas flow rate) varied to observe the change of arc voltage and to establish the model for the monitoring. The arc voltage was decreased when the wire was fed to the backward eccentric position(over 2mm), and the shield gas flow rate was insufficient under 10L/min. In the case of the backward eccentric position over 2mm, the bead appearance was not good and the dilution ratio was increased due to deep penetration. When the shield gas flow rate was lower than 10L/min, the bead surface was oxidized.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.17 no.3
• /
• pp.3795-3814
• /
• 1975

The purpoes of this thesis is to study the effect of the variation of the beginning date of the suspension of irrigation and the length of intermittent suspension period of irrigation in the paddy field on the growth and yield of rice, so as the provide a critical limit of saving irrigation water and an irrigation method to prevent drough damage in rice cultivation. In this experiment, the rice variety adopted was NONGRIM No.29. There were seven main test plot, each test plot having a different beginning date of the suspension of irrigation. A main test plot was susdivided into five small test plots, each having a different length of the suspension period of irrigation. The results obtained in this experiment are summarized as follows: 1. The number of tillers is controlled by the treatment of the suspension of irrigation, its beginning date being early of late. The reductive effects of beginning dates of suspension upon the number of tillers. investigated on July 30, are about 84% for the treatment suspended on July 8, 87% on July 12, and 92% on July 19, respectively, in comparison with the standard plot. However. the suspenion treatments after the foregoing dates does not affect the control of their numbers. On the other hand, the lengths of intermittent suspension periods influence highly on the number of tillers to be restrained considerably, the decrease ratio ranging from 91% to 80% Both treatments on dates and periods are so intermingled that the restraining effects of suspension periods become greater as the dates of its beginning are earlier. 2. The elongation of plant hieghts also restrained considerably by the longer periods and earlier dates of suspension treatments of irrigation. Especially, the effects of the lengths of suspension periods become more serious. 3. Heading dates are delayed by two to five days through the suspension treatments of irrigation. However, the heading stage ends almost on the same day without relation to the differences between the irrigation suspension treatments. In the test plot where the suspension date of irrigation comes after the young panicle forming stage, the heading stage ends one or two days later than in the standard test plot. 4. Both culm lengths and panicle lengths show significant differences in their values, i.e., their lengths are shorter, as the begining dates of irrigation suspension are earlier and the suspension periods are longer. 5. The earlier the beginning date and the longer the period of irrigation suspension, the less is the number of panicles per hill in comparison with the standard plot. 6. The earlier the beginning date and the longer the period of irrigation suspension, the higher is the significant difference in the number of kernels per panicle in comparison with that in the standard test plot, i.e., the less is the number of kernels per panicle. 7. The earlier the beginning date and the longer the period of irrigation suspension, the lighter are the weights of rough rice and straws per hill in comparison with those in the standard plot.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1963-1966
• /
• 2005

Degenerative lumbar spinal stenosis(DLSS) is a disease inducing low back pain, leg pain, convulsion, numbness, and neurogenic claudication from compression of nerve root. Intervertebra fixation was reported to increase the degenerative of neighbor region after treatment. Recently, a new surgical technique of inserting a fixator between interspinous processes has been introduced. The purpose of this study is to design of the interspinous process fixator with flexibility to complement the trouble of using fixator in DLSS. This study evaluated the existing fixator through the mechanical test and modified fixators using the finite element analysis(FEA). Displacement, stiffness and Von-Mises stress were found to have similar values to those obtained from the mechanical test and the FEA in the biomechanical loading condition. Effects of variation in length and thickness were investigated to design an optimal fixator.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.3 s.180
• /
• pp.195-202
• /
• 2006

The degenerative lumbar spinal stenosis (DLSS) is a disease inducing low back pain, leg pain, convulsion. numbness, and neurogenic claudication from compression of nerve root. Intervertebra fixation was reported to increase the degeneration of neighbor lesion after treatment. Recently, a new surgical technique of inserting a fixator between interspinous processes has been introduced. The purpose of this study is to design the interspinous process fixator with flexibility to complement the trouble of using fixator in DLSS. This study evaluated the existing fixator through the mechanical test and modified it using the finite element analysis (FEA). The evaluation was based on the displacement, stiffness and von-Mises stress obtained from the mechanical test and calculated from the FEA in the biomechanical loading condition. Effects of variation in length and thickness were investigated to design an optimal fixator. Three prototypes were manufactured using FEA results. Mechanical tests under the biomechanical loading condition were performed to select the best one from these three. The selected fixator increased flexiblity by 32.9%.

• Journal of Welding and Joining
• /
• v.33 no.2
• /
• pp.62-68
• /
• 2015

This study investigates the appropriate range of reverse bending load for the CTOD test of thick weld by observing improvement of pre-crack shape and determination of the limit applicable load. In order to do it, the effect of the amount of the reverse bending load on the maximum deviation of the pre-crack length was investigated by the extensive tests, and the variation of plastic zone size in way of the crack tip under reverse bending load were evaluated by FEA. With the results obtained by the experiments and FEA, the proper range of reverse bending load was suggested. The effectiveness of the reverse bending method was verified by examining the pre-crack straightness after CTOD tests of thick weld specimens with various thickness and strength.