• Progress in Superconductivity
• /
• 제5권1호
• /
• pp.61-64
• /
• 2003

In HTS transformer with double pancake windings, the perpendicular component of leakage magnetic flux density ($B_{r}$ ) applied to HTS tapes of double pancake windings of HTS transformer acts as a cause to decrease the critical current in HTS tape. So, in this paper, HTS transformer with reciprocal arrangement winding is designed. And in order to investigate the$ B_{r}$ applied to HTS windings, the 2-D non-linear electromagnetic analysis of HTS transformer is performed by using the OPERA 2D. The maximum $B_{r}$ applied to winding of HTS transformer is 0.112 T and the characteristics of HTS transformer were also obtained. But in this type of winding arrangement, reciprocal arrangement, the generated ac-loss to the HTS windings is very high because of the applied $B_{r}$ to HTS windings. Therefore, in order to reduce the generated ac-loss to the HTS windings, the new design of HTS transformer with concentric winding arrangement is presented in this paper and the 2-D non-linear electromagnetic analysis and the ac-loss for HTS transformer with the concentric winding arrangement is also carried out.

• 한국산학기술학회논문지
• /
• 제13권4호
• /
• pp.1480-1487
• /
• 2012

최근, 국내 탄광의 안전성이 향상되고 있으나 사고는 꾸준히 발생하고 있다. 대부분의 터널 지보는 I빔과 I빔을 연결하는 이음판 부분에서 지압을 견디지 못하고 파손이 발생한다. XX 탄광의 경우, 터널지보의 아치부가 일반적인 굽힘 거동이 아닌, 위쪽 방향으로 굽힘이 발생하고 있다. 이러한 경우는 터널지보에 수직하중 이외에 수평하중이 과대하게 작용하는 경우로 볼 수 있으며 이러한 수평하중은 지하암반의 급격한 변화에 의한 암반의 이완범위의 증가나 지하수의 누출 등으로 인한 수리학적인 요인 등의 복합적인 문제가 작용하여 나타난다. 따라서 본 연구에서는 위쪽 방향으로 굽힘을 일으키는 수평하중의 크기를 추정하기 위하여 실험계획법과 최적화 알고리듬을 적용하여 터널지보의 굽힘거동을 규명하였다.

• 한국해양공학회지
• /
• 제24권6호
• /
• pp.76-80
• /
• 2010

Oil hydraulic piston pumps are being extensively used around the world, because of their simple design, light weight, effective cost, etc. An oil hydraulic pump is likely to have the serious problems of high leakage, friction, and low energy efficiency after a long period of use. In an oil hydraulic piston pump, the clearance between the valve block and piston plays an important role for volumetric and overall efficiency. In this study, the wear property of the SACM645 material with DLC coating used for a hydraulic piston pump was determined by experimentation with variable heat treatment. To investigate the effect according to the piston surface condition, five different types of specimens were prepared. The maximum tensile strengths of the QT and QT Nitration specimens had similar values of about 800 MPa, but the strains indicated a big difference. In a wear test, the wear characteristic of the DLC coating specimen was shown to be excellent. The QT, QT + IH, QT + Nitration, and matirx specimen showed similar wear characteristics. In the case of a dry condition without oil, the DLC coating specimen had good wear resistance, with no wear shown.

• 상하수도학회지
• /
• 제26권5호
• /
• pp.609-617
• /
• 2012

A dynamic water quality model is presented in order to simulate water quality under slowly varying flow conditions over time. To improve numerical accuracy, the proposed model uses a lumped system approach instead of extended period simulation, unlike the other available models. This approach can achieve computational efficiency by assuming liquid and pipe walls to be rigid, unlike the method of characteristics, which has been successfully implemented in rapidly varying flows. The discrete volume method is applied to resolve the advection and reaction terms of the transport equation for water quality constituents in pipes. Numerical applications are implemented to the pipe network examples under steady and unsteady conditions as well as hydraulic and water quality simulations. The numerical results are compared with EPANET2, which is a widely used simulation model for a water distribution system. The model results are in good agreement with EPANET2 for steady-state simulation. However, the hydraulic simulation results under unsteady flows differ from those of EPANET2, which causes a deviation in water quality prediction. The proposed model is expected to be a component of an integrated operation model for a water distribution system if it is combined with a computational model for rapidly varying flows to estimate leakage, pipe roughness, and intensive water quality.

• 한국환경보건학회지
• /
• 제7권2호
• /
• pp.73-87
• /
• 1981

Generation of Solid Wastes grew rapidly with the increase of living standard of the people in Korea recently and their composition was more complicate. The weight of Solid wastes generated in Seoul into year of 1979 was about 420 million tons which required 1.5 million $m^2$ of burial land and daily generation for person was 1.6kg. The Composition of more than 80% ash contents was suitable for sanitary landfill but recently ash was decreasing while paper, synthetic materials, glass etc, increasing and alternative method had to be found to dispose the wastes properly. Weight and Composition of Wastes by season and living standard were surveyed for one year from June 1980 to May 1981 in Seoul. Disposal mathods by waste composition was studied. Results were summarized as follows: 1) Each component stored separately at generation point was to be collected and to be reused or disposed by public organization or private company. Some incentives have to be arranged. 2) Wastes collected from household were transfeted to about 420 temporally storing places and transported to two dumping areas by about 700, 4-8 tons trucks which droped litters on the streets. Large dumping lots should constructed along the western coasts and the wastes would be transported through big container trucks or trains to the lots. 3) Ash contents decreased to 40-70% while garbage, synthetic materials, paper increased and they are two to three times in summer of those in winter. Ash in affluent residential areas is less than 50% of whole wastes while that in poor apartment and residential areas is 60-70%. 4) Large dumping places should be constructed along the western coasts which are not far from Seoul because no suitalbe lands are available, and proper leakage protection arrangements should be made.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• 제5B권4호
• /
• pp.366-373
• /
• 2005

This paper presents two new circuit topologies of the dc busline side active resonant snubber assisted voltage source high frequency link soft switching PWM full-bridge dc-dc power converters acceptable for either utility ac 200V-rms or ac 400V-rms input grid. These high frequency switching dc-dc converters proposed in this paper are composed of a typical voltage source-fed full-bridge PWM inverter, high frequency transformer with center tap, high frequency diode rectifier with inductor input filter and dc busline side series switches with the aid of a dc busline parallel capacitive lossless snubber. All the active switches in the full-bridge arms as well as dc busline snubber can achieve ZCS turn-on and ZVS turn-off transition commutation with the aid of a transformer leakage inductive component and consequently the total switching power losses can be effectively reduced. So that, a high switching frequency operation of IGBTs in the voltage source full bridge inverter can be actually designed more than about 20 kHz. It is confirmed that the more the switching frequency of full-bridge soft switching inverter increases, the more soft switching PWM dc-dc converter with a high frequency transformer link has remarkable advantages for its power conversion efficiency and power density implementations as compared with the conventional hard switching PWM inverter type dc-dc power converter. The effectiveness of these new dc-dc power converter topologies can be proved to be more suitable for low voltage and large current dc-dc power supply as arc welding equipment from a practical point of view.

• 한국구조물진단유지관리공학회 논문집
• /
• 제15권5호
• /
• pp.75-81
• /
• 2011

최근 건설되는 교량은 철근 콘크리트 대신에 주로 프리스트레스트 콘크리트 교량이 주종을 이루고 있다. 프리스트레스 콘크리트 (PSC)는 철근 콘크리트 (RC)가 지니는 균열발생 문제, 철근의 부식, 누수 등 내구성에 미치는 약점을 보완할 수 있다. 또한 프리스트레싱으로 인한 인장영역의 보완으로 인하여 구조물의 크기를 줄일 수 있다. 하지만 이러한 구조용 주재료인 고강도 콘크리트의 경우는 밀도가 강도에 비하여 상대적으로 크기 때문에 상대적으로 자중을 증대시키는 문제가 있다. 따라서 자중을 감소시킬 수 있는 경량골재를 활용한 중공형 PPC 거더 (Hollowed Prefabricated Prestressed Concrete girder systems using Light Aggregate, 이하 HPPCLA)는 이러한 문제점을 해결할 수 있는 대안이 될 수 있다. 본 연구에서는 HPPCLA 거더의 성능시험 뿐 만 아니라 수치해석을 수행하였으며, 그 결과 HPPCLA 거더는 전형적인 휨파괴 형상을 나타내었다. 수치해석에서 예상한 바와 같이 PPC 거더의 사용하중인 110 kN에서는 완전한 탄성거동으로 구조물의 사용성에는 무리가 없을 것으로 판단된다.

• 한국자기학회지
• /
• 제23권2호
• /
• pp.68-76
• /
• 2013

자기유도형 기반의 무선전력 전송 기술을 이용한 무선충전 기능이 최근 스마트폰 등에 채용되어 주요한 소비자 편의기능으로 자리잡고 있다. 무선전력전송 모듈은 무선전력 전송효율을 개선하고 휴대폰 주요 회로부에 대한 전자기장 간섭을 억제하기 위하여 전자기장 차폐 소재의 사용이 필수적이다. 본 논문에서는 무선전력 전송모듈용 전자기장 차폐 소재의 역할과 기술에 대해 소개하였다. 이와 함께 향후 확산될 중급 전력(mid-power)과 대전력(high-power)영역의 무선전력 전송 응용분야에서 대응 가능한 차폐 소재의 개발 방향을 정리하였다.

• 한국재료학회지
• /
• 제8권12호
• /
• pp.1152-1157
• /
• 1998

금속 타겟들을 이용한 반응성 스퍼터링법으로 $460~540^{\circ}C$범위에서 $Pt/Ti/SiO_2$/Si 기판위에 PZT 박막을 증착하였다. Perovskite상의 핵형성을 위해 Pb 휘발이 적은 저온($480^{\circ}C$)에서 짧은 시간 동안 PZT 박막을 증착한 후 Pb가 PBT 박막내에 과잉으로 함유되는 것을 억제하기 위하여 증착 온도를 증가시켜 박막을 증착하는 2단계 증착법을 사용한 결과 54$0^{\circ}C$의 고온에서도 perovskite 단일상과 화학양론비에 가까운 조성을 얻을 수 있었다. 2단계 증착법으로 제조된 PZT 박막은 우수한 전기적 특성을 나타내었으며 후속 RTA 처리로 더욱 특성을 향상시킬 수 있었는데 $17\mu$C/$\textrm{cm}^2$의 잔류분극, 45kv/cm의 coercive field, 그러고 -500kv/cm의 높은 전기장에서도 $10^{-4}$ A/$\textrm{cm}^2$의 양호한 누설전류 특성을 나타내었다.

• 한국압력기기공학회 논문집
• /
• 제6권2호
• /
• pp.20-27
• /
• 2010

In order to prevent the corrosion of component contacted primary water designed alloy 600 material in the nuclear power plant. But the primary water stress corrosion cracking(PWSCC) of alloy 600 and weld area occurs continuously due to the residual stress. The leakage accident resulted from PWSCC in the drain nozzle of the steam generator of domestic power plants. Heater sleeves of the pressurizer are welded with alloy 600 weld material and therefore exposed to the primary water environment. PWSCC occurred in heater sleeve material and weld area of many foreign power plants. The current issue of domestic nuclear power plants are consequently concentrated to PWSCC of similar material. In order to improve the detection and the sizing of the PWSCC in the welding sleeve of the pressurizer, the automatic UT system and multi-directions probe sets have been developed. The experimental studies have been performed using the mock-up block containing artificial reflectors(ID connected EDM notch) and semi-artificial cracks made from thermal fatigue. The automatic UT System is applied in the detection and the length sizing of the ID/OD on the tube and the J-groove weld area of the artificial reflectors and results of the detection and the sizing are compared respectively. Also, the developed automatic UT system is successfully accomplished to inspect the heater sleeve and the J-groove weld area on the pressurizer for the detection of PWSCC.