• Journal of Welding and Joining
• /
• v.32 no.3
• /
• pp.74-80
• /
• 2014

Due to environmental regulations (RoHS, WEEE and ELV) of the European Union, electronics and automotive electronics have to eliminate toxic substance from their devices and system. Especially, reliability issue of lead-free solder joint is increasing in car electronics due to ELV (End-of-Life Vehicle) banning from 2016. We have prepared engine control unit (ECU) modules soldered with Sn-40Pb and Sn-3.0Ag-0.5Cu (SAC305) solders, respectively. Degradation characteristics of solder joint strength were compared with various conditions of automobile environment such as cabin and engine room. Thermal cycle test (TC, $-40^{\circ}C$ ~ ($85^{\circ}C$ and $125^{\circ}C$), 1500 cycles) were conducted with automotive company standard. To compare shear strength degradation rate with eutectic and Pb-free solder alloy, we measured shear strength of chip components and its size from cabin and engine ECU modules. Based on the TC test results, finally, we have known the difference of degradation level with solder alloys and use environmental conditions. Solder joints degradation rate of engine room ECU is superior to cabin ECU due to large CTE (coefficient of thermal expansion) mismatch in field condition. Degradation rate of engine room ECU is 50~60% larger than cabin room electronics.

• Journal of Mechanical Science and Technology
• /
• v.19 no.8
• /
• pp.1529-1543
• /
• 2005

Recently an unmanned aerial vehicle (UAV) has been widely used for military and civil applications. The role of a navigation system in the UAV is to provide navigation data to the flight control computer (FCC) for guidance and control. Since performance of the FCC is highly reliant on the navigation data, a fault in the navigation system may lead to a disastrous failure of the whole UAV. Therefore, the navigation system should possess a fault detection and isolation (FDI) algorithm. This paper proposes an attitude determination GPS/INS integrated navigation system with an FDI algorithm for a UAV. Hardware for the proposed navigation system has been developed. The developed hardware comprises a commercial inertial measurement unit (IMU) and the integrated navigation package (INP) which includes an attitude determination GPS (ADGPS) receiver and a navigation computer unit (NCU). The navigation algorithm was implemented in a real-time operating system with a multi-tasking structure. To evaluate performance of the proposed navigation system, a flight test has been performed using a small aircraft. The test results show that the proposed navigation system can give accurate navigation results even in a high dynamic environment.

• Journal of Korean Society of Transportation
• /
• v.36 no.2
• /
• pp.98-111
• /
• 2018

Truck platooning, which is a cluster of trucks in support of vehicle-to-vehicle communication and automated longitudinal vehicle control, is a promising method to both operational efficiency and prevent traffic crashes. Although a variety of studies have been conducted to identify the effects of vehicle platooning on traffic stream, we are not aware of any study attempting to identify promising road segments for vehicle platooning. This study aims to develop a methodology for determining the priority of freeway segments that would potentially lead to maximize the effectiveness of truck platooning. Evaluation measures derived in this study includes truck crash rates, the percentage of truck traffic, segment length, and the number of entry and exit points. Weighting values obtained from an analytical hierarchical process (AHP) method were applied to compute the proposed priority score to determine better freeway segment for truck platooning. Results suggested that a 46.9km freeway segment, from Sacheon IC to Sanin JC, was the most promising segment for maximizing the effectiveness of truck platooning. It is expected that the outcome of this study would be effectively used as a fundamental to establish operational strategies for truck platooning.

• The Korean Journal of Emergency Medical Services
• /
• v.1 no.1
• /
• pp.100-111
• /
• 1997

This is the first Korea study to evaluate the effects od the safety of ambulance driving and the occurrence of ambulance traffic accidents and to provide basic informaion for the description of various factors to reduce the ambulance traffic accidents. The major insturment of this study were Krean Self-Analysis Driver Opinionnaire. Questionnaire contains 8 items which measure driver's opinions or attitudes : driving courtesy, emotion, traffic law, speed, vehicle conditions, the use of drugs, high-risk behaviors, and human factors. To take the analysis of data, the total of 350 divers were investigated ambulance divers and others in Taejon City and others (6 City) from 1996. 1. July to 1996. 31. July. The data were analyzed by the descriptive statistics and the logistic regression - path analysis - with SPSS and SAS package program. The result are as follows : 1. There was desirable attitude group(16.2%) and undesirable attitude group(17.6%) on safety ambulance driving. 2. It have suggested that risk factors of ambulance traffic accidents much affected with emotion and speed control on safety ambulance driving < Y(Accdient) = -2.64 + 0.57 $X_1$ (Emotion Control) + 0.30 $X_2$(Seed control) + E > and motor traffic acident much affected with emotion control and high-risk behavior on safety driving < Y(Accident) = -1.11 + 0.33 $X_1$(Emotion Control) + 0.29 $X_2$(High-risk Behvior) + E > 4. The primary emphassis of ambulance drivers was make us realized that improthatnt factors on safety ambulance driving were 1)making way for emergent ambulance, 2)driver's career, 3)The ability of emergency medical technics, and the knowledge or under standing of ambulance way difficut(or easy) of accdess. 5. Almost 96.6% of respondents have agreed to necessity of emergency medical technics for ambulance drivers. 6. Almost 94.6% of respondents have consented to necessity of emergtency medical technicians for ambulance driving. 7. It have suggested that the proportion of traffic accident proportion by desitable attitude group(16.7%) was much less than that of undesirable attitude group(30.8%) on safety ambulance driving(P < 0.05)/Ps) Accidents are unplanned, unforesen incidents which can lead to harmful or unfortunate outcomes, Collisons are not accidents, since the basic cause of the majority of collisons invovles high-risk human behavior. Although there are many factors which contribute to accident causation, four basic factors seem to predominate in most traffic related situations. These four factors include: the human factor, the vehicle factor, the environmental factors and destination factor(Peto G. et al. 1995).

• International Journal of Highway Engineering
• /
• v.17 no.1
• /
• pp.91-98
• /
• 2015

PURPOSES : Although signalized intersections have been considered the best way to control traffic volume in urban areas for several decades, roundabouts are currently being discussed as an alternative way to control traffic volume, especially when traffic is light. Because a roundabout's efficiency depends on the load geometry as well as the traffic volume, design guidelines for roundabouts are recommended only if the incoming traffic volume is very low. It is rare to substitute a roundabout for an existing signalized intersection in urban areas. This study aims to estimate the benefits from the transformation of an existing signalized intersection into a roundabout in an urban area. When there is a more moderate volume of traffic, roundabouts can be effectively used by optimizing signals located at an approaching roadway. METHODS : The methodologies of this paper are as follows: First, a signalized intersection was analyzed to determine the traffic characteristics. Second, the signalized intersection was transformed into a roundabout using VISSIM microscopic traffic simulation. Then, we estimated and analyzed the effects and the performance of the roundabout. In addition, we adjusted a method to improve the benefits of the transformation via the optimization of signals located at an approaching road to control the incoming traffic volume. RESULTS : The results of this research are as follows: The signal-optimized roundabout improved delays compared with the signalized intersection during the morning peak hour, non-peak hour, and evening peak hour by 1.78%, 12.45%, and 12.72%, respectively. CONCLUSIONS : According to the simulation results of each scenarios, the signal-optimized roundabout had less delay time than the signalized intersection. If optimized signal control algorithms are installed in roundabouts in the future, this will lead to more efficient traffic management.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.6
• /
• pp.112-119
• /
• 2006

This paper is concerned with the light-weight design of a center-pillar assembly for the high-speed side impact of vehicle using advanced high strength steels(AHSS). Steel industries continuously promote the ULSAB-AVC project for applying AHSS to structural parts as an alternative way to improve the crashworthiness and the fuel efficiency because it has the superior strength compared to the conventional steel. In order to simulate deformation behavior of the center-pillar assembly, a simplified center-pillar model is developed and parts of that are subdivided employing tailor-welded blanks(TWB) in order to control the deformation shape of the center-pillar assembly. The thickness of each part which constitutes the simplified model is selected as a design parameter. Factorial design is carried out aiming at the application and configuration of AHSS to simplified side-impact analysis because it needs tremendous computing time to consider all combinations of parts. In optimization of the center-pillar, S-shaped deformation is targeted to guarantee the reduction of the injury level of a driver dummy in the crash test. The objective function is constructed so as to minimize the weight and lead to S-shape deformation mode. Optimization also includes the weight reduction comparing with the case using conventional steels. The result shows that the AHSS can be utilized effectively for minimization of the vehicle weight and induction of S-shaped deformation.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.23 no.4
• /
• pp.410-419
• /
• 2015

In this study, the roadability, fuel economy and emission characteristics were evaluated for a natural gas converted vehicle. The results are as follows; Not only the shortage of power was observed in stall test, but also large deterioration of acceleration performance was exposed in roadability. Compared to the original LPG system, the acceleration is 76% in start acceleration and 45 ~ 65% in overtaking acceleration, especially the decline became larger when air conditioner is at work. Furthermore, because the mapping data, which controls the injection depending on driving condition, do not match up with injection system, the failure of air-fuel ratio feedback control occurs resulting from the large gap between the required and the really supplied amount of fuel. This failure cause the exhaust gas to emit without catalytic conversion and the fuel economy based on the fuel heat value to get worse 22% in the mode test and 16% in road test respectively. In addition, the existing injection system does not secure enough fuel at the starting so that it may lead to the fail of clod start, the deterioration of hot start and inharmonic of engine at the idle after start.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.6
• /
• pp.84-92
• /
• 2005

This paper is concerned with optimum design of a center-pillar assembly induced by the high-speed side impact of the vehicle. In order to simulate deformation behavior of the center-pillar assembly, simplified finite element model of the center-pillar and a moving deformable barrier are developed based on results of the crash analysis of a full vehicle model. In optimization of the deformation shape of the center-pillar, S-shaped deformation is targeted to guarantee reduction of the injury level of a driver dummy in the crash test. Tailor-welded blanks are adopted in the simplified center-pillar model to control the deformation shape of the center-pillar assembly. The thickness of each part which constitutes the simplified model is selected as a design parameter. The thickness of parts which have significant effect on the deformation mechanism are selected as design parameters with sensitivity analysis based on the design of experiment technique. The objective function is constructed so as to minimize the weight and lead to an S-mode deformation shape. The result shows that the simplified model can be utilized effectively for optimum design of the center-pillar members with remarkable saving of computing time.

• KEPCO Journal on Electric Power and Energy
• /
• v.8 no.2
• /
• pp.69-72
• /
• 2022

This paper actually investigates the load on major large-scale buildings in the downtown area, examines the economic feasibility of installing PV and ESS in a microgrid target building, and evaluates whether an electric vehicle capable of V2G through two buildings is effective as an economical analysis program (HOMER) was analyzed using. It is economical to install a mixture of ESS rather than using the whole PV, and it is shown that if there is an electric vehicle using the V2G function of EV, there is an economic effect to replace the PV. So that Incentives and policies are needed to replace a large area of PV and utilize the existing parking lot to lead EV as a resource of the microgrid. Currently, P2X technology that stores power as ESS or converts it to other energy to control when surplus renewable energy occurs in large-capacity solar power plants and wind farms, etc. This is being applied, and efforts are being made to maintain the stability of the system through the management of surplus power, such as replacing thermal energy through a heat pump. Due to the increase in electric vehicles, which were recognized only as a means of transportation, technologies for using electric vehicles are developing. Accordingly, existing gas stations do not only supply traditional chemical fuels, but electricity, and super stations that also produce electricity have appeared. Super Station is a new concept power plant that can produce and store electricity using solar power, ESS, V2G, and P2G. To take advantage of this, research on an urban microgrid that forms an independent system by tying a large building and several buildings together and supplies power through a super station around the microgrid is in full swing.

• Toxicological Research
• /
• v.25 no.2
• /
• pp.79-84
• /
• 2009

Cerium oxide nanoparticles (size: 30 nm) were prepared by the supercritical synthesis method, Acute oral toxicity and tissue distribution of the nanoparticles were evaluated by a single administration in rats. Oral administration of the nanoparticles to the rats did not lead to death when the animals were treated by a dose of 5 g/kg (high dose) as well as 100 mg/kg (low dose). Abnormal clinical signs, changes in serum biochemistry and hematology were not observed in high-dose treated group compared to the vehicle control group. Lesions in liver, lung and kidney were not observed in high-dose treated group by histopathological examination. Tissue distribution analysis in liver, kidney, spleen, lung, testis and brain was performed on day 1, day 7 and day 14 after treatment. The average values of the accumulated cerium oxide nanoparticles were elevated in all tissues but statistical significance was only shown in lung. Low levels of tissue distributions after a single oral administration seem to be the low bioavailability of the nanoparticles.