• The Journal of Engineering Geology
• /
• v.7 no.2
• /
• pp.113-126
• /
• 1997

Electrical resistivity methods of dipole - dipole array profiling and Schiumberger array sounding were tested on a segment of the Woraksan granitic batholith for the research into the imaging of irregular attitudes of fracture zones in the crystaaline rock in terms of processing and interpretation schemes. By the dipole - dipole array method, inhomogeneities such as small scale of fracture zones were properly delineated down at some depth even within hard rock environment. Fracture zones were interpreted to be at the boundaries between the high amplitude zone and very low amplitude zone in the resistivity plot and they were also successfully outlined in two - dimensional layer and pseudo - three - dimensional volume constructed by the incorporation of vertical sounding data. The surface location of the fracture zones was correlated by the zero - crossing point in the VLF(very low frequency) electromagnetic data. Pseudo - three - dimensional attitudes of fracture zones were efficiently illuminated by optimum projection angle. The mean of bulk resistivity for the Woraksan granite and the near fracture zones is estimated to be approximately of 4,000 ohm - m which is much higher than the value of 700 ohm - m for the Rwachunri limesilicate environment. This difference is due to both the rock type, i.e., biotite granite vs limesilicate, and the occurrence of secondary openings of fold and fault associated with the intrusion of granite. In this study statistical analyses on the resistivity color plot were performed in terms of three representative statistical moments, i.e., standard deviation, skewness, and kurtosis. The fracture zones in the standard deviation plot were characterized by the higher value, compared to the value of homogeneous portion. The upper boundary of the high resistivity zone was also successfully delineated in the skewness and kurtosis plots.

• Journal of the Korean Society of Laryngology, Phoniatrics and Logopedics
• /
• v.30 no.2
• /
• pp.101-106
• /
• 2019

Background and Objectives Reinke's edema is a benign vocal fold disease caused by an edematous laryngeal superficial layer of lamina propria. The first line treatment is cessation of smoking and laryngeal microsurgery. The aim of the study is to evaluate the feasibility and efficacy of percutaneous steroid injection via cricothyroid membrane in patients with Reinke's edema. Materials and Method From Jan 2010 to July 2018, 33 Patients with Reinke's edema managed by vocal fold steroid injection via the cricothyroid membrane were included in this study. We compared medical records of laryngoscopy, stroboscopy and Multi-Dimensional Voice Program analysis at pre-treatment and post-treatment. Subjective voice improvement was evaluated using Voice Handicap Index-30 (VHI-30). Results 75.7% of the patients showed partial response and 6.06% showed complete response. 93.94% were present smokers and only 4 patients ceased smoking after the treatment. In acoustic analysis, the pre-treatment mean value of jitter, shimmer, and noise to harmonic ratio was 2.30±3.21, 9.34±10.37, 1.11±2.90 each. The post-treatment value was 2.20±1.89, 6.96±5.30, 0.20±0.09 respectively and none of the parameters were statistically significant. For subjective symptom improvement, 25 (75.8%) patients showed a better score on post-treatment VHI-30 compared to pre-treatment. Conclusion According to our study, steroid injection is a relatively safe and effective procedure for patients with Reinke's edema. A vocal fold steroid injection via the cricothyroid membrane can be an alternative treatment option for those who are not able to undergo conventional laryngeal microscopic surgery, however cessation of smoking is necessary for effective treatment.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.11 no.1
• /
• pp.53-62
• /
• 1987

High power lasers provide a controllable and precise energy source in surface transformation hardening. A careful control of the process is needed in order that the surface layer of the material reaches the austenizing temperature, but that it does not melt. In order to achieve this the results of theoretical and experimental studies on the laser surface hardening of a medium carbon steel are described. A two-dimensional computer program, which can be used generally for the determination of transient temperature distributions in welding and heat treatment, was established on the basis of the finite element method. For the confirmation of the accuracy of the numerical analysis, a medium carbon steel (SM 45C) of 5mm thickness was heat-treated with a 1kW CW CO$_{2}$ laser machine, while the traverse speed and the distance from the focal point (defocused distance) were varied. Experimental and numerical results showed a similar tendency in correlations between the hardened zone shape and the process parameters. With increasing beam spot diameter the width and depth of the hardened zone increased for relatively small beam spot diameters, but decreased rapidly after reaching the maximum value, while with increasing traverse speed the width and depth of the hardened zone decreased monotonously. Too small beam spot diameters are to be avoided, since the surface melting would lower the surface hardness and produce an uneven surface which may be unacceptable because of the possible requirement for subsequent machining. It could be observed that for a given traverse speed and laser power input there exists a optimal range of the beam spot diameter, which produce a large width of the hardened zone but no melting on the surface.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.4 no.3
• /
• pp.187-193
• /
• 1984

Using the stratifying clip method, we examine the differences in vertical distribution of leaf area and its relationships with dry matter production were investigated in the primary swards of six varieties. The results obtained were as follows: 1. The varieties could be classified into 4 different types according to their of vertical distribution of leaf area within the canopy. Thus, M had a greater leaf area distribution in the base layers and became smaller towards the upper layers, Leto, First and Bundy had the leaf area distribution which was most abundant in the middle layers and became smaller towards the base and the upper layers, Tammisto had a greater leaf area distribution in the middle layers and intensively distributed to the upper layers, and Trader had the relatively uniform leaf area distribution over all layers. 2. Effective leaf area index(ELAI) correlated with leaf area index(LAI), dry weight of plant(DW), stem weight of plant(SW) and stem area index(SAI). 3. The variety with the heading tiller type had the effective leaf area intensively distributed to the upper layers of canopy, but the vegetative type showed a high ratio of effective leaf area index. 4. Varietal differenced was found between the effective leaf area and specific leaf weight(SLW) in each stratum above the layer indicating the highest leaf area density within the canopy. M and Trader had a highly negative significant correlation, but the other varieties was not significant correlation.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.46 no.3
• /
• pp.221-228
• /
• 2001

This study was carried out to investigate the effect of germination condition and drying temperature on growth and physicochemical properties of brown rice. Three brown rice seeds of Ilpumbyeo, Dasanbyeo and Heugjinjubyeo were stored at room temperature for six weeks to test the time-sequence germination viability. Relatively stable germination ratio was maintained until 2 weeks after storage. However, 3 weeks after storage, germination ratio of brown rice seeds started to decrease rapidly and their germination ratio was lower than 80%. For this reason, brown rice was recommended for seeding within 2 weeks after hulling. During the initial 5 days, germination ratio of 24 hours pre-soaking brown rice was higher about 2-3% than that of non-soaking brown rice. The $25^{\circ}C$ was considered as the most favorable temperature for brown rice germination, because of the high germination ratio and desirable coleoptile growth of the brown rice, and little seed rotting symptoms. The scanning electron micrographs showed the structural differences between hot-air dried and freeze dried germinated-brown rice kernel. In the freeze dried germinated-brown rice, seed coat (pericarp, tegmen and aleurone layer) was mechanically disrupted from the endosperm, and many cleavages were observed among starch storing cells and starch granules. The endosperm of freeze-dried brown rice kernels formed the sponge-like structures and showed the fragile traits. For this reason, hot-air drying is considered as more suitable method than freeze drying for germinated-brown rice. The crude protein and amylose contents were slightly changed, but there were no significant differences during the germination period. Crude fiber content was decreased, but crude Int and total amino acid contents were increased as seeding days increased. A rapid increase in $\alpha$-amylase activities of germinating brown rice was observed at S days after seeding, and $\alpha$-amylase activities were decreased from 8 days after seeding. Total free sugar contents were decreased during the germination period. There was continuous decline in the contents of sucrose and glucose until 8 days after seeding, but fructose and maltose content were gradually increased from the 5 days after seeding.

• Journal of Pharmacopuncture
• /
• v.15 no.4
• /
• pp.52-65
• /
• 2012

Objectives: Toad venom, called Chan-Su, is a traditional Oriental medicine secreted from the auricular and the skin glands of the Bufo bufo gargarizanz Cantor or B. melanosticus Schneider and has been widely used in China, Korea and other parts of Asia for the treatment of pain, heart conditions, and cancer. We examined the concentrations of the main chemical constituents within a commercially available toad venom product and compared the levels for different extraction methods. Methods: Toad venom was extracted using either cold or hot water, ethanol (EtOH), methanol (MeOH), or ethyl acetate (EtOAc), was fractionated using precipitation or reflux, and was then analyzed using thin layer chromatography (TLC), high-performance liquid chromatography (HTLC), and liquid chroma-tography - mass spectrometry (LC-MS). Individual components were identified by comparisons of the retention times, the ultraviolet spectra, and mass spectras and differences in chemical constituents for different solvents and extraction methods are presented. Results: Components with authentic standards, including serotonin and bufodienolides (cinobufagen, bufalin, cinobufalin, and resibufogenin), were detected. The water extract of toad venom contained the greatest amount of serotonin ($75.7{\pm}0.1$ mg/g), but very small amounts of bufodienolides ($3.8{\pm}0.0$ mg/g). In contrast, the use of MeOH or EtOH extraction solutions resulted in 5-26 times higher concentrations of bufodienolides, with only trace amounts of serotonin. The relative and the absolute concentrations of the component also varied based on the extraction method; i.e., EtOH extracts yielded the greatest total amounts of bufodienolides, and EtOAc precipitation had the lowest amounts of bufodienolides. Conclusions: Toad venom consists of serotonin and several bufodienolides, and the choice of solvent to extract chemical the constituents is important as a way to enrich the purported active components for treating different conditions.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.195-195
• /
• 2016

Titanium and its alloys are widely used as implants in orthopedics, dentistry and cardiology due to their outstanding properties, such as high strength, high level of hemocompatibility and enhanced biocompatibility. Hence, recent works showed that the synthesis of new Ti-based alloys for implant application involves more biocompatible metallic alloying element, such as, Nb, Hf, Zr and Mo. In particular, Nb and Hf are one of the most effective Ti ${\beta}-stabilizer$ and reducing the elastic modulus. Plasma electrolyte oxidation (PEO) is known as excellent method in the biocompatibility of biomaterial due to quickly coating time and controlled coating condition. The anodized oxide layer and diameter modulation of Ti alloys can be obtained function of improvement of cell adhesion. Silicon (Si) and magnesium (Mg) has a beneficial effect on bone. Si in particular has been found to be essential for normal bone and cartilage growth and development. In vitro studies have shown that Mg plays very important roles in essential for normal growth and metabolism of skeletal tissue in vertebrates and can be detected as minor constituents in teeth and bone. The aim of this study is to research Si and Mg doped hydroxyapatite film formation by plasma electrolytic oxidation. Ti-29Nb-xHf (x= 0, 3, 7 and 15wt%, mass fraction) alloys were prepared Ti-29Nb-xHf alloys of containing Hf up from 0 wt% to 15 wt% were melted by using a vacuum furnace. Ti-29Nb-xHf alloys were homogenized for 2 hr at $1050^{\circ}C$. Each alloy was anodized in solution containing typically 0.15 M calcium acetate monohydrate + 0.02 M calcium glycerophosphate at room temperature. A direct current power source was used for the process of anodization. Anodized alloys was prepared using 270V~300V anodization voltage at room. A Si and Mg coating was produced by RF-magnetron sputtering system. RF power of 100W was applied to the target for 1h at room temperature. The microstructure, phase and composition of Si and Mg coated oxide surface of Ti-29Nb-xHf alloys were examined by FE-SEM, EDS, and XRD.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.197-197
• /
• 2016

Commercially pure titanium (CP Ti) and Ti-6Al-4V alloys have been widely used for biomedical applications. However, the use of the Ti-6Al-4V alloy in biomaterial is then a subject of controversy because aluminum ions and vanadium oxide have potential detrimental influence on the human body due to vanadium and aluminum. Hence, recent works showed that the synthesis of new Ti-based alloys for implant application involves more biocompatible metallic alloying element, such as, Nb, Hf, Zr and Mo. In particular, Nb and Hf are one of the most effective Ti ${\beta}-stabilizer$ and reducing the elastic modulus. Plasma electrolyte oxidation (PEO) is known as excellent method in the biocompatibility of biomaterial due to quickly coating time and controlled coating condition. The anodized oxide layer and diameter modulation of Ti alloys can be obtained function of improvement of cell adhesion. Manganese(Mn) plays very important roles in essential for normal growth and metabolism of skeletal tissue in vertebrates and can be detected as minor constituents in teeth and bone. Radio frequency(RF) magnetron sputtering in the various PVD methods has high deposition rates, high-purity films, extremely high adhesion of films, and excellent uniform layers for depositing a wide range of materials, including metals, alloys and ceramics like a hydroxyapatite. The aim of this study is to research the Mn coatings on the micro-pore formed Ti-29Nb-xHf alloys by RF-magnetron sputtering for dental applications. Ti-29Nb-xHf (x= 0, 3, 7 and 15wt%, mass fraction) alloys were prepared Ti-29Nb-xHf alloys of containing Hf up from 0 wt% to 15 wt% were melted by using a vacuum furnace. Ti-29Nb-xHf alloys were homogenized for 2 hr at $1050^{\circ}C$. Each alloy was anodized in solution containing typically 0.15 M calcium acetate monohydrate + 0.02 M calcium glycerophosphate at room temperature. A direct current power source was used for the process of anodization. Anodized alloys was prepared using 270V~300V anodization voltage at room. Mn coatings was produced by RF-magnetron sputtering system. RF power of 100W was applied to the target for 1h at room temperature. The microstructure, phase and composition of Mn coated oxide surface of Ti-29Nb-xHf alloys were examined by FE-SEM, EDS, and XRD.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.199-199
• /
• 2016

Commercially pure titanium (cp-Ti) and Ti alloys (typically Ti-6Al-4V) display excellent corrosion resistance and biocompatibility. Although the chemical composition and topography are considered important, the mechanical properties of the material and the loading conditions in the host have, conventionally. Ti and its alloys are not bioactive. Therefore, they do not chemically bond to the bone, whereas they physically bond with bone tissue. The electrochemical deposition process provides an effective surface for biocompatibility because large surface area can be served to cell proliferation. Electrochemical deposition method is an attractive technique for the deposition of hydroxyapatite (HAp). However, the adhesions of these coatings to the Ti surface needs to be improved for clinical used. Plasma electrolyte oxidation (PEO) enables control in the chemical com position, porous structure, and thickness of the $TiO_2$ layer on Ti surface. In addition, previous studies h ave concluded that the presence of $Ca^{+2}$ and ${PO_4}^{3-}$ ion coating on porous $TiO_2$ surface induced adhesion strength between HAp and Ti surface during electrochemical deposition. Silicon (Si) in particular has been found to be essential for normal bone and cartilage growth and development. Zinc (Zn) plays very important roles in bone formation and immune system regulation, and is also the most abundant trace element in bone. The objective of this work was to study electrochemical characteristcs of Zn and Si coating on Ti-6Al-4V by PEO treatment. The coating process involves two steps: 1) formation of porous $TiO_2$ on Ti-6Al-4V at high potential. A pulsed DC power supply was employed. 2) Electrochemical tests were carried out using potentiodynamic and AC impedance methoeds. The morphology, the chemical composition, and the micro-structure an alysis of the sample were examined using FE-SEM, EDS, and XRD. The enhancements of the HAp forming ability arise from $Si/Zn-TiO_2$ surface, which has formed the reduction of the Si/Zn ions. The promising results successfully demonstrate the immense potential of $Si/Zn-TiO_2$ coatings in dental and biomaterials applications.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.20 no.4
• /
• pp.314-321
• /
• 2000

A gap between a $Al_2O_3/Fe$ thermite and lower head vessel is formed in the lower-plenum arrested vessel attack(LAVA) experiment which is the 1st phase study of simulation of naturally arrested vessel attack in vessel(SONATA-IV). The gap measurement using a conventional ultrasonic method would be lack of a reliability due to the structure complexity and the metallurgical grain size change of the lower head HAZ occurred by a thermite $Al_2O_3/Fe$ melt or a $Al_2O_3$ melt at $2300^{\circ}C$. The grain echoes having false signals and lower S/N ratio signals are detected due to a multiple scattering, a mode conversion and an attenuation of a ultrasonic resulted from at the interface of increased grain size zone. In this test, the signals pattern was classified to understand the behavior of the ultrasonic in a multi-layer specimen of solid-liquid-solid of assuming that the thermite and the lower head vessel is immersed. The polarity threshold algorithm of frequency diversity gives us the enhancement about 6dB of the ratio S/N.