• Journal of Surface Science and Engineering
• /
• v.56 no.2
• /
• pp.147-151
• /
• 2023

Transparent ZnO (100 nm thick) and ZnO/Ti/ZnO (ZTZ) films were prepared with radio frequency (RF) and direct current (DC) magnetron sputtering on the glass substrate at room temperature. During the ZTZ film deposition, the thickness of the Ti interlayer was varied, such as 6, 9, 12, and 15 nm, while the thickness of ZnO films was kept at 50 nm to investigate the effect of the Ti interlayer on the crystallization and opto-electrical performance of the films. From the XRD pattern, it is concluded that the 9 nm thick Ti interlayer showed some characteristic peaks of Ti (200) and (220), and the grain size of the ZnO (002) enlarged from 13.32 to 15.28 nm as Ti interlayer thickness increased. In an opto-electrical performance observation, ZnO single-layer films show a figure of merit of 1.4×10^-11 Ω^-1, while ZTZ films with a 9 nm-thick Ti interlayer show a higher figure of merit of 2.0×10^-5 Ω^-1.

• Journal of Sericultural and Entomological Science
• /
• v.13 no.2
• /
• pp.123-133
• /
• 1971

The author is the first man who tried to use an anesthetic on insect specially for silkworm in orde to evaluate the silkworm health and silk yielding ability and the obtained results are as followings. 1. The necessary ether vapor induction for narcosis on silkworms is varied by the glowth of the silkworm which the larger worm is, the longer induction is required. For instance, it was 2∼3 minutes for the worms of third day fifth instar silkworm in case use of ether anesthetic. 2. The longer anesthetic induction for silkworms, the longer recovery needs from anesthesia. In case five minutes ether vapor induction, silkworms recovered narcosis during in 5∼130 minutes which had varied very much by the health variation. 3. The ether induction caused silkworm to vomit digestive juice from a few per cent of the worms, but the chloroform induction showed majority of the worms to vomit the digestive juice out of mouth. So, the ether was found as better anesthetic for silkworms. 4. When ether induction last more than 20∼30 minutes, the recovered silkworms can eat mulberry, but when it gets more than three hours they can not eat mulberry. And when it last more than ten minutes, the silkworm may eat mulberry leaf, but they can not spinn cocoon properly. 5. In case five minutes ether induction for silkworms on third day fifth instar, the stronger variety is, the rallier recovered from narcosis. 6. The recovering duration from narcosis varies regarding with each worm health which shows Poisson′s distribution even in a same variety silkworm. 7. The female worms recover from narcosis earlier than male worms which means the female worm is stronger than male one. 8. The later recovered silkworm from narcosis spinned more rich cocoon silk and ended with smaller pupae weight. Such a tendency showed until at some recovery duration, then the silk yield droped down on the worms recovered in more longer duration. The author (Choe) had named such a relation curve as "Silk Yield Curve against Silkworm Health." 9. The silk yield or cocoon layer ratio had varied from 13 to 27% even in a same worm varity cocoon which showed serious variation and call attention carefulness for the duplication work of a variety silkworm eggs. 10. Not always the rich silk yielding worm is the best worm during the silkworm selection and it should be considered with the silkworm health evaluation. 11. At present situation, only specific breeding expert is allowed to join in the selection service because of need many years experience by use of visual observation, but the ether anesthesia method may help such an evaluation with more accuracy and easy way even for the people in fresh on the field. 12. The effect of the narcosis on the silkworm for the next generation or hybrid worm will be reported in next publication.

• Journal of The Geomorphological Association of Korea
• /
• v.18 no.2
• /
• pp.25-37
• /
• 2011

The purpose of this study is to investigate the history of phenomenon(hereinafter called mass-movement) of movement of inorganic material originated from hillslope by denudation of hillslope surrounding the watershed during Holocen period in the Chaamgol watershed(hereinafter called study watershed) uppermost stream of Maegokcheon Cheonan-si Chungnam. To do this, for the object of allivium distributed in valley bottom of study watershed, facies analysis, radiocarbon dating and grain size analysis were conducted and geomorphological analysis on study watershed conducted together. The result is like the following. It was confirmed that over around 9,100yrBP~to recent due to a few times of mass-movement occurred in time scale of 10²~10³ years, a large quantity of inorganic material is mixed in organic material layer originated from wetland formed in valley bottom of study watershed or exists between organic material layers. And it was found that in study watershed, mass-movement occurred in instable period of hillslope after the Early Holocen existed at least 8 times (M1 period~M8 period) and wetland environment formed in the stable period of hill slope existed total 4 times (W1 period~W4 period). This analysis result will be used in the future as basic material in research of Holocen climate change of Maegokcheon watershed and in restoration of denudation process of hillslope following this.

• Geomechanics and Engineering
• /
• v.35 no.2
• /
• pp.121-133
• /
• 2023

The demand for cement and limestone crushed materials has increased many folds due to the tremendous increase in construction activities in Pakistan during the past few decades. The number of cement production industries has increased correspondingly, and so the rock-blasting operations at the limestone quarry sites. However, the safety procedures warranted at these sites for the blast-induced ground vibrations (BIGV) have not been adequately developed and/or implemented. Proper prediction and monitoring of BIGV are necessary to ensure the safety of structures in the vicinity of these quarry sites. In this paper, an attempt has been made to predict BIGV using artificial neural network (ANN) at three selected limestone quarries of Pakistan. The ANN has been developed in Python using Keras with sequential model and dense layers. The hyper parameters and neurons in each of the activation layers has been optimized using randomized and grid search method. The input parameters for the model include distance, a maximum charge per delay (MCPD), depth of hole, burden, spacing, and number of blast holes, whereas, peak particle velocity (PPV) is taken as the only output parameter. A total of 110 blast vibrations datasets were recorded from three different limestone quarries. The dataset has been divided into 85% for neural network training, and 15% for testing of the network. A five-layer ANN is trained with Rectified Linear Unit (ReLU) activation function, Adam optimization algorithm with a learning rate of 0.001, and batch size of 32 with the topology of 6-32-32-256-1. The blast datasets were utilized to compare the performance of ANN, multivariate regression analysis (MVRA), and empirical predictors. The performance was evaluated using the coefficient of determination (R²), mean absolute error (MAE), mean squared error (MSE), mean absolute percentage error (MAPE), and root mean squared error (RMSE)for predicted and measured PPV. To determine the relative influence of each parameter on the PPV, sensitivity analyses were performed for all input parameters. The analyses reveal that ANN performs superior than MVRA and other empirical predictors, andthat83% PPV is affected by distance and MCPD while hole depth, number of blast holes, burden and spacing contribute for the remaining 17%. This research provides valuable insights into improving safety measures and ensuring the structural integrity of buildings near limestone quarry sites.

• Science of Emotion and Sensibility
• /
• v.27 no.1
• /
• pp.59-68
• /
• 2024

This study aimed to develop a soft fabric-based elbow-bending angle sensor that can replace conventional hard-type inertial sensors and a system for estimating bending angles using it. To enhance comfort during exercise, this study treated four fabrics (Bergamo, E-band, span cushion, and polyester) by single-walled carbon nanotube dip coating to create conductive textiles. Subsequently, one fabric was selected based on performance evaluations, and an elbow flexion angle sensor was fabricated. Gauge factor, hysteresis, and sensing range were employed as performance evaluation metrics. The data obtained using the fabricated sensor showed different trends in sensor values for the changes in the angle during bending and extending movements. Because of this divergence, the two movements were separated, and this constituted the one-step process. In the two-step process, multilayer perceptron (MLP) was employed to handle the complex nonlinear relationships and achieve high data accuracy. Based on the results of this study, we anticipate effective utilization in various smart wearable and healthcare domains. Consequently, a soft- fabric bending angle sensor was developed, and using MLP, nonlinear relationships can be addressed, enabling angle estimation. Based on the results of this study, we anticipate the effective utilization of the developed system in smart wearables and healthcare.

• Restorative Dentistry and Endodontics
• /
• v.36 no.4
• /
• pp.280-289
• /
• 2011

Objectives: The purpose of this study was to evaluate ${\mu}TBS$ (microtensile bond strength) of current dentin bonding adhesives which have different hydrophobicity with low-shrinkage silorane resin. Materials and Methods: Thirty-six human third molars were used. Middle dentin was exposed. The teeth were randomly assigned to nine experimental groups: Silorane self-etch adhesives (SS), SS + phosphoric acid etching (SS + pa), Adper easy bond (AE), AE + Silorane system bonding (AE + SSb), Clearfil SE bond (CSE), CSE + SSb, All-Bond 2 (AB2), AB2 + SSb, All-Bond 3 (AB3). After adhesive's were applied, the clinical crowns were restored with Filtek LS (3M ESPE). The 0.8 mm ${\times}$ 0.8 mm sticks were submitted to a tensile load using a Micro Tensile Tester (Bisco Inc.). Water sorption was measured to estimate hydrophobicity adhesives. Results: ${\mu}TBS$ of silorane resin to 5 adhesives: SS, 23.2 MPa; CSE, 19.4 MPa; AB3, 30.3 MPa; AB2 and AE, no bond. Additional layering of SSb: CSE + SSb, 26.2 MPa; AB2 + SSb, 33.9 MPa; AE + SSb, no bond. High value of ${\mu}TBS$ was related to cohesive failure. SS showed the lowest water sorption. AE showed the highest solubility. Conclusions: The hydrophobicity of adhesive increased, and silorane resin bond-strength was also increased. Additional hydrophobic adhesive layer did not increase the bond-strength to silorane resin except AB2 + SSb. All-Bond 3 showed similar ${\mu}TBS$ & water sorption with SS. By these facts, we could reach a conclusion that All-Bond 3 is a competitive adhesive which can replace the Silorane adhesive system.

• Horticultural Science & Technology
• /
• v.28 no.6
• /
• pp.996-1002
• /
• 2010

Flow cytometry (FCM) was used to measure the ploidy level of three different sports from 'Campbell Early' ($Vitis$ $labruscana$) grape. Results of the study showed different ploidy levels. FCM analysis for 'Campbell Early' grape which contains 2C DNA diploid cells showed single peak around 35-40 while 'Kyoho' grape with 4C DNA tetraploid cells had a different level of 70-80. However, analysis of the sports displayed a histogram with 2 peaks containing both 2C and 4C nuclei. There was no difference in histograms of 2C DNA flesh and pericarp; on the other hand, 4C DNA flesh type of sports had a different histogram from that of the 2C DNA pericarp. Chromosome numbers of diploid ('Campbell Early'), tetraploid ('Kyoho'), and three sports were counted under the microscope. 'Campbell Early' and 'Kyoho' have 38 and 76 chromosomes, respectively. Three different sports are mixoploids with mixtures of diploid and tetraploid cells. Microscopic observations of shoot apical meristems in sports from 'Campbell Early' grape were carried out to determine the type of plant chimera. 'Campbell Early' grape (diploid) and 'Kyoho' grape (tetraploid) showed that both had 2 tunica layers covering corpus cells, while the three different sports had tunica layers showing mostly oblique division. Most cells from 'Kyoho' grape were larger than 'Campbell Early' grape. Cells from L-2 and L-3 layers of the three sports were similar to 'Kyoho' grape in size, although all cells in L-1 surface layer were uniform in size like 'Campbell Early' grape. Results of FCM analysis indicated that both normal and polyploid cells could be intermixed in sports and could become mixoploidy consisting of diploid and tetraploid. All sports used in the tests were periclinal chimera plants with two distinct L-1 and L-2 cell layers. The result of this study suggests that all three sports which originated from 'Campbell Early' grape might be 2-4-4 type chimera formation.

• Korean Journal of Environmental Agriculture
• /
• v.25 no.4
• /
• pp.306-315
• /
• 2006

Two different experiments, adsorption/desorption and runoff by rainfall simulation of four pesticides, such as alachlor, ethalfluralin, ethoprophos and pendimethalin were undertaken their runoff and erosion losses from sloped land and to assess the influence of their properties and environmental factors on them. The mobility of four pesticides and which phase they were transported by were examined in adsorption study, and the influence of rainfall pattern and sloping degree on the pesticide losses were evaluated in simulated rainfall study. Freundlich adsorption parameters (K) by the adsorption and desorption methods were 1.2 and 2.2 for ethoprophos, 1.5 and 2.6 for alachlor, respectively. And adsorption distribution coefficients (Kd) by the adsorption and desorption methods were 56 and 94 for ethalfluralin, and 104 and 189 for pendimethalin, respectively. K or Kd values of pesticides by the desorption method which were desorbed from the soil after thoroughly mixing, were higher than these ones by the adsorption method which pesticides dissolved in water were adsorbed to the soil. Another parameter (1/n), representing the linearity of adsorption, in Freundlich equation for the pesticides tested ranged from 0.96 to 1.02 by the desorption method and from 0.87 to 1.02 by the adsorption method. Therefore, the desorption method was more independent from pesticide concentration in soil solution than the adsorption method. By Soil Survey and Land Research Center (SSLRC)'s classification for pesticide mobility, alachlor and ethoprophos were classified into moderately mobile $(75{\leq}Koc<500)$, and ethalfluralin and pendimethalin were included to non-mobile class (Koc > 4000). Runoff and erosion loss of pesticides by three rainfall scenarios were from 1.0 to 6.4% and from 0.3 to 1.2% for alachlor, from 1.0 to 2.5% and from 1.7 to 10.1% for ethalfluralin, from 1.3 to 2.9% and from 3.9 to 10.8% for pendimethalin, and from 0.6 to 2.7% and from 0.1 % 0.3% for ethoprophos, respectively. Distribution of pesticides in soil profile were investigated after the simulated rainfall study. Alachlor and ethoprophos were leached to from 10 to 15 cm of soil layer, but ethalfluralin and pendimethalin were mostly remained at the top 5 cm of soil profile. The losses of the pesticides at 30% of sloping degree were from 0.2 to 1.9 times higher than those at 10%. The difference of their runoff loss was related with their concentration in runoff water while the difference of their erosion loss must be closely related with the quantity of soil eroded.

• Journal of Animal Environmental Science
• /
• v.8 no.1
• /
• pp.9-16
• /
• 2002

This study was conducted to develope the new solid separating system which can be efficiently and economically removed the solid parts in high pollutants concentration of pig slurry. The pollutants concentration, BOD$_{5}$ , COD and SS of the slurry used in this study was 15,990($\pm$2,389)mg/l, 20,004($\pm$5,512)mg/l and 26,486($\pm$5,935)mg/l, respectively. After removal of solid part in slurry, the pollutants concentration, BOD$_{5}$, COD and SS was change into 5,617($\pm$690)mg/l, 5,553($\pm$633)mg/land 1,456($\pm$341)mg/l, respectively in the Fixed biological membrane tank. The reduction of the pollutants concentration of suspend liquid through membrane will be allowed to greatly improve the water purification by an Activated sludge method. This separating system consisted of a temporary storage, a circulating tank and a Fixed Biological membrane tank. A temporary storage which has a draining system of screw type and an aeration device played a tremendous role in draining the solid by filled an aeration of 0.3 l/min. A Fixed Biological membrane tank of which a styrofoam filled in a 2/3 volume as a Biological media was fixed by a stainless steel net (pore size : 0.5mm) to separate the liquid layer of influx in them. The separating system efficiency factors were the speed of screw motor, cycle number of slurries in a circulating tank and moisture contents of solid effluent through the screw path. Although the pollutants concentration was very variable in temporary storage, the final concentration of $BOD_5$ and SS, except COD of the suspended liquid in a Fixed biological membrane were not different regardless of cycle number of a circulating tank. Moisture contents of effluent from temporary storage was 73% under the speed 1 ppm of screw motor and 62% under the 1/4rpm of it.

• Korean Journal of Microbiology
• /
• v.39 no.3
• /
• pp.166-174
• /
• 2003

Microcystin produced by cyanobacteria in surface waters, such as eutrophic lake and river, is a kind of serious environmental problems due to its toxicity to human and wild animals. Microcystin is synthesized nonribosomally by the large modular multi-functional enzyme complex known as microcystin synthetase encoded by the mcy gene cluster. Amplification of mcy genes by PCR from cultures and environmental samples is a simple and efficient method to detect the toxigenic Microcystis. In order to evaluate primers designed to detect toxic microcystin-producing strains, 17 cyanobacterial strains and 20 environmental samples were examined by PCR with 7 pairs of primers. Some microcystin-producing cyanobacteria were not detected with FAA-RAA, TOX4F-TOX4R and FP-RP primers. The fragment of unexpected size was amplified with NSZW2-NSZW1 primers in Microcystis strains isolated from the lakes in Korea. TOX1P-TOX1F primers failed in amplification of toxin-producing strains. Only MSF-MSR and TOX2P- TOX2F primers amplified the fragments of mcy genes from 11 strains of microcystin-producing Microcystis. The water samples taken from 20 lakes in Korea were analyzed by PCR using each of the primers. In all the water samples, cyanobacteria capable of producing microcystin were detected by the PCR with TOX2P-TOX2F primers. These results indicate that TOX2P-TOX2F primers are better than the other primers for detection of microcystin-producing Microcystis strains in Korea. The nucleotide sequences of mcy gene in Microcystis aeruginosa NIER10010 suggest genetic diversity of Korean isolates.