• Journal of the Korean Society for Railway
• /
• v.20 no.3
• /
• pp.299-310
• /
• 2017

In this work, an independent-load friction wedge model was developed using the ADAMS/View program to predict the performance of a freight vehicle with a bogie employing a 3-piece friction wedge. The friction wedge model can generate friction according to lateral and vertical directions of the bolster. The developed friction wedge model was applied to the ADAMS/Rail vehicle model, and results of the dynamic analysis showed a critical speed of 210km/h. In the linear safety analysis, it was confirmed that the lateral and vertical limit of acceleration of the vehicle were satisfied based on UIC518. In the 300R curve line, the application speed was 70km/h, which was satisfied with the limit acceleration of the car-body and bogie based on UIC518. Also, the developed model satisfied the wheel loading, lateral force and derailment coefficient of "The Regulations on Safety Standards for Railway Vehicles"

• Journal of the Korean Society of Radiology
• /
• v.18 no.4
• /
• pp.335-344
• /
• 2024

In this study, we aim to investigate the correlation between the lateral images of Korean skulls and the angle between the OML and the Body of the Mandible. Additionally, we seek to provide criteria for the ease of positioning in clinical settings and establish standardized imaging procedures for the PNS Water's view examination. This study was conducted on a total of 202 patients who visited the radiology department of a general hospital and examined the skull lateral radiography. In addition to the patient images, skull phantoms were also utilized, and images were obtained using GC85A and EOS equipment. In this research, abbreviations related to the angle of the Body of Mandible were defined using PACS on lateral images. Measurements were taken for various angles, including ramus of mandible angle(RIA), accurate OML angle(TIA), OML and IR Angle(OIA), total mandibular length(TML), ramus height(RH), the angle between the pogonion, gonion, and condylion(MA). The validity of these measurements was confirmed using the skull phantom in the study. The age-specific average range for RIA was 22.67° to 26.04°, with measurements of 23.14° for males and 24.78° for females. The age-related mean ranges for TIA and OIA were 35.98° to 38.31° and 72.27° to 75.25°, respectively. For males, TIA was 36.74° and OIA was 72.73°, while for females, TIA was 36.43° and OIA was 73.38°. The age-dependent measurements for TML and RH ranged from 85.73 mm to 89.60 mm and 62.60 mm to 70.87 mm, respectively. Male values were 90.54 mm and 70.78 mm, while female values were 85.13 mm and 61.54 mm for TML and RH, respectively. The age-specific average range for MA was 55.95° to 58.63°, with measurements of 57.96° for males and 57.76° for females. Correlation analysis revealed a positive correlation between RIA and OIA, as well as between RIA and TIA. Based on the results of this study, which indicate a positive correlation between the angle of the Body of Mandible and the OML, it can be inferred that adjusting the mandible vertically to align with the imaging receptor may contribute to more accurate image acquisition during PNS Water's view examination. Therefore, it is believed that there is value in utilizing this relationship as a criterion for establishing new positioning standards, which could enhance the utility of a new positioning guide.

• Journal of radiological science and technology
• /
• v.31 no.2
• /
• pp.109-114
• /
• 2008

There is a standard shoulder oblique method (Grashey method) available to view the shoulder joint. This method projects AP view of the shoulder joint so that the Humerus head's subuxation or joint degeneration can be easily visualized. However, in this view, the patients, with supine or sitting or erect position, have to keep their body obliquely. Whereas, the patients who are not well or operated, usually feel very uncomfortable to keep their body in this position and hence, we need other persons' help and much efforts will be needed to get the good quality shoulder joint view. Therefore, we thought of examining a method which shows the joint well by angling the tube to Medio-Lateral direction and without keeping the patients' one side upward in supine position. For this study, total 15 subjects with no history of neurological or psychiatric illness, were recruited for examinations. They consisted of 9 males and 6 females. Statistic group analysis was performed with ANOVA test. Scores of the evaluation of the experts were $1.10{\pm}0.54$ at $25^{\circ}$, $2.50{\pm}0.50$ at 30^{\circ}$, $2.85{\pm}0.36$ at $35^{\circ}$ and $2.33{\pm}0.47$ at $40^{\circ}$, respectively, and they were significant(p<0.05, Table 1). Joint space of the Humerus head and Scapula were well distinguished at $35^{\circ}$, $30^{\circ}$ and $40^{\circ}$ with the almost same score. However, the degree of distortion at $40^{\circ}$ was more severe than that at $30^{\circ}$. Ultimately, $30-35^{\circ}$ views were shown to yield good quality shoulder oblique images. In conclusion, this method may be very useful for the patients who are uncomfortable and for the emergency patients. In order to get similar or comparable view, the same X-tube angle is recommended to be used before and after the operation. Therefore, we hope that this new angled method seems to be efficient.

• Journal of the Korean Society of Radiology
• /
• v.7 no.4
• /
• pp.271-275
• /
• 2013

Shoulder bone scan everyday life, sports activities at the side of the shoulder joint, or applying strong force in the lateral occurs. Mainly on upper arm abduction, temple, other rotational dislocation of the shoulder joint gahaejyeo as useful for observing the presence or absence of lesions is used. Shoulder PA oblique projection prevent distortion of the image due to the angle and the most useful diagnostic radiological investigate shooting angle. Shoulder blade body and the acromion and coracoid process Y-view is formed characters. $10^{\circ}$ angle between the shoulder blades and the acromion is the obstruction. $20^{\circ}{\sim}25^{\circ}$ to the Y-view of the humerus head looks superimposed, the position of the shoulder joint and seemed appropriate. $35^{\circ}$ of the humerus head superimposed on the Y-view, but above the humerus head and shoulder joints were distorted. When $45^{\circ}$ elevation observed on the side of the best has come Y-view also acromion and coracoid process is finished.

• Journal of Technologic Dentistry
• /
• v.45 no.3
• /
• pp.81-86
• /
• 2023

Purpose: This study aimed to observe the effect of laminate veneer on patient's teeth based on the manufacturing of laminate veneer restorations, which are produced by fabricating a ceramic cast body using IPS Empress, a pressure casting method and then forming the veneer by layering. Subsequently, we assessed the potential of its clinical application. Methods: This study discusses and preserves various treatment plans, such as diagnostic wax-up and treatment room diagnosis, for patients who visit the hospital to improve the appearance of teeth due to diastema of maxillary teeth, inexperienced resin filling, lack of esthetics, and external teeth. A ceramic cast body is constructed using IPS Empress, which is an effective and aesthetic restoration pressure casting method to restore the veneer with a laminate made by layering. Results: Compared with the preoperative state, the frontal view of the patient after the final restoration showed the formation of a natural smile line; the space between the central and lateral incisors was filled in synchronously with the adjacent teeth. In addition, the emergence profile is maintained by reducing the over-contour as much as possible. Conclusion: The patient's quality of life is improved by providing them with a satisfactory natural smile.

• The Korean Journal of Pain
• /
• v.10 no.2
• /
• pp.254-257
• /
• 1997

Ganglion impar lies immediately anterior to the sacrococcygeal junction and blockade of the ganglion is used to treat anorectal and perineal pain. Although the technique introduced by Plancarte et at is widely practised, the bent needle is sometimes difficult to position precisely and patients find the procedure painful. We modified this approach of block of ganglion impar by positioning the needle into the sacrococcygeal junction and using the loss of resistance technique. With the patient in the lateral position, a skin wheal was raised at 1-1.5cm below the sacral hiatus. Twenty-three gauge short needle was directly placed into the sacrococcygeal junction with aid of fluoroscopic guidance. From 1 cm behind the anterior margin of the vertebral body in lateral view, we used the loss of resistance technique to confirm the retroperitoneal space. We found this modified approach easier to perform during six blocks for three patients with anorectal or perineal pain. Our modified approach through the sacrococcygeal junction may provide opportunity for wider administration of this procedure because of its simple technique, reduced pain during procedure and decreased risk of infection.

• International Journal of Costume and Fashion
• /
• v.5 no.1
• /
• pp.1-13
• /
• 2005

Two hundreds of female aged 19 years old and up were recruited to evaluate the postural changes and bilateral variation of asymmetry over age. To find out the differences among the age group, subjects were classified into 5 groups, early young age(19-29), late young age(30-39), early middle age(40-49), late middle age(50-59), and old age(60-). 35 body measurements were taken by the 3-D body scanner which allowed us to take measurements which cannot be measured using traditional methods, including the shape of a cross section, slice area surface are, and volume. Bilateral variations were observed as a function of age; Depth of scapular point level, scapular point to center back, and blade angle. Postural change of anterior cervical angle, upper anterior thoracic angle, upper posterior thoracic angle, posterior cervical angle, and center back/center front ratio were also exhibited. In each measurements, subjects were classified into normal, and abnormal group. Percentiles of abnormal in shoulder line angle, blade angle, neck point $\∼$ acromial point $\∼$ scapular point, posterior cervical angle, and upper posterior thoracic angle were increased over age group. The upper body of lateral view was classified into 3 types of posture based on the previous research; straight, erect(leaning back), and stooped(bent forward). The percentiles of subjects who have straight postures were decreased as a function of age, but those of stooped postures were increased. Subjects who have erect postures did not so. The stooped posture group shows the big cervical fossa angle, anterior cervical angle, posterior cervical angle, upper posterior thoracic angle, and the small upper anterior thoracic angle comparing to the straight and erect posture group. These results could be apply for clothing construction reflecting the changes in back, shoulder, neck, and the bilateral asymmetry according to the target age group.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.46 no.1
• /
• pp.48-56
• /
• 2019

The objective of this study was to examine measuring agreement between middle phalanx of the third finger and cervical vertebrae analysis for assessing skeletal maturity according to body mass index percentile. A retrospective chart view was used to select patients with body mass index data, hand - wrist radiographs and lateral cephalograms of same day. The patients were divided into 4 groups by body mass index percentile. The hand - wrist radiographs were analyzed using modified middle phalanx of the third finger method and the lateral cephalograms were categorized according to cervical vertebral maturation stage. The degree of agreement between the 2 methods of analyzing skeletal maturation was measured by calculating weighted kappa statistic according to body mass index percentile group. There was a good agreement between the 2 methods in the entire body mass index percentile group. According to the body mass index percentile group, the agreement was found to be different, and the pattern was different between boys and girls. Pediatric dentist should consider sex and weight status when evaluating growing children and adolescents because it can affect the agreement of 2 method of analyzing skeletal maturation.

• The Korean Journal of Pain
• /
• v.14 no.2
• /
• pp.199-206
• /
• 2001

Background: The lumbar sympathetic ganglia are variable in both position and numbers. The aim of this study was to detect the appropriate lumbar vertebral level where the lumbar sympathetic ganglia primarily aggregate. Methods: Forty patients comprising of hyperhidrosis (26 cases), complex regional pain syndrome (10 cases), peripheral artery occlusion disease (3 cases) and postherpetic neuralgia (1 case) underwent lumbar sympathetic block. We randomly selected one of two (L2 or L3) levels and the L4 level. The position of the needle tip and distribution of dye was verified by injection of a mixture of radio-opaque dye (1.5 ml) and 4% lidocaine (1.5 ml) and subsequently confirmed by L-spine anteroposterior and a lateral view X-ray. We considered the response positive when the skin temperature increased more than $1^{\circ}C$ in 5 min. Results: In general, the positive response ratio was greater when the needle tip located at the L2 or L4 level vice L3 and when the drug was distributed on the lower half of the L4 body and in the L4/5 intervertebral disc space. In a right side block, the positive response ratio was greater when the drug was distributed on the lower half of the L4 body and in the L4/5 intervertebral disc space, although in a left side block there was no significant difference seen between the levels. The complications of the neurolytic block were alcohol neuritis (7.5%) and hypoesthesia (5%) on the L1 or L2 dermatome. Conclusions: The best effect with least chance of complication may be induced by spreading the drug on the lower half of the L4 body and/or into the L4/5 intervertebral disc space by placing the needle tip on the L4 body.

• The korean journal of orthodontics
• /
• v.26 no.4
• /
• pp.414-420
• /
• 1996

Cephalometric measureements have disadvantage of representing cranio-facial structures in two dimension only and therefore they pose limitations in describing three-dimentional structures of cranio-facial region. More interests have been put on the correlation between the two planes. This study evaluated correlations between facial type score, which allows effects on malocclusion, growth change prediction and establishment of treatment method and prognosis, and measurements from submentovertex view. Cephalometric view and submentovertex view were taken of skeletal Class I adults with optimal profile and correlations between them have been observed. Following results were obtained: 1. To learn about factors that influence average condylar angulation, FACE, INT-CO-ANG, MN-CORPUS, CON-RATIO, GON-RATIO, MN-RATIO were used as variables and underwent multiple regression analysis. As a result, the following equation was obtained : CON-AVE=.l73(FACE)-.322(INT-CO-ANG)+36.34(GON-RATIO) +.420(MN-CORPUS) (($R^2=.85451$) 2. The following equation was obtained concerning facial type score. FACE= .050(CON-ANG)+.023(INT-CO-ANG)-.075(MN-CORPUS)($R^2=.31547$) 3. Among the submentovertex measurements, MN-CORPUS, CON-RATIO, GON-RATIO, MN-RATIO showed close correlations. (P<0.05) 4. Average condylar angualtions were $23.37^{\circ}$ on the right and $20.71^{\circ}$ on left. There was a difference between the two. FACE : facial type soore. CON-ANG: mean value of condylar angulation. CON-AVE: mean value of Rt. Lt condylar angulation. INT-CO-ANG : angle between Rt. Lt condylar axis. MN-CORPUS : angle formed between RT. Lt gonion & pogonion. CON-RATIO: lntercondylar distance/mandibular body length. GON-RATIO : intergonion distanoe/mandibular body length. MN-RATIO: lntermylohyoid distance/mandibular body length. MX-RATIO: intermaxillary tuberosity distance/ANS-PNS distance.