• The Journal of Korean Academy of Prosthodontics
• /
• v.44 no.5
• /
• pp.642-653
• /
• 2006

Purpose : The purpose of this study was to investigate the effect of the output energy(voltage) of laser welding on the strength and properties of joint of cast titanium(CP Gr II) and titanium alloy(Ti-6Al-4V). Material and method : Cast titanium and its alloy rods(ISO6871) were prepared and perpendicularly cut at the center of the rod. After the cut halves were fixed in a jig, and the joints welded with a laser-welding machine at several levels of output voltage of $200V{\sim}280V$. Uncut specimens served as the non-welded control specimens The pulse duration and pulse spot size employed in this study were 10ms and 1.0mm respectively. Tensile testing was conducted at a crosshead speed of 0.5mm/min. The ultimate tensile strength(MPa) was recorded, and the data (n=6) were statistically analyzed by one-way analysis of variance(ANOVA) and Scheffe's test at ${\alpha}$=0.05. The fracture surface of specimens investigated by scanning electron microscope (SEM). Vickers microhardness was measured under 500g load of 15seconds with the optimal condition of output voltage 280V. Results : The results of this study were obtained as follows, 1. When the pulse duration and spot size were fixed at 10ms and 1.0mm respectively, increasing the output energy(voltage) increased UTS values and penetration depth of laser welded to titanium and titanium alloy. 2. For the commercial titanium grade II, ultimate tensile strength(665.3MPa) of the specimens laser-welded at voltage of 280V were not statistically(p>0.05) different from the non-welded control specimens (680.2MPa). 3. For the titanium alloy(Ti-6Al-4V), ultimate tensile strength(988.3MPa) of the specimens laser-welded at voltage of 280V were statistically(p<0.05) different from the non-welded control specimens (665.0MPa). 4. The commercial titanium grade II and titanium alloy(Ti-6Al-4V) were Vickers microhardness values were increased in the fusion zone and there were no significant differences in base metal, heat-affected zone.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.111-111
• /
• 2009

전 세계적으로 환경 보호의 차원에서 자동차 업체는 자동차의 연비 향상을 위한 차체의 경량화가 큰 이슈로 대두되고 있다. 이를 위해 알루미늄과 같은 경량화 소재를 이용하여 차체 조립에 투입하고자 연구 중에 있다. 이와 같은 레이저 용접 공정이 현장에 적용되기 위해서는 용접부의 품질을 실시간으로 모니터링하고 품질을 판단하여야 생산성을 극대화 할 수 있다. 그러므로 본 연구에서는 알루미늄 AA5182 알루미늄 판재의 용가 와이어를 이용한 레이저 용접에서 용접부를 모니터링 할 수 있는 시스템을 구축하였다. 이를 위하여 레이저는 4kW급 Nd:YAG 레이저를 사용하였고, 차체용 알루미늄 판재 AA5182 1.4t를 AA5356 와이어를 이용하여 용접을 수행하였다. 모니터링 센서로는 반응 범위가 190 mn~680 nm인 센서를 이용하였고, 용접 중 센서로부터 발생된 출력전류를, 신호 증폭기와 DAQ 보드를 통해 초당 10,000 samples/sec로 계측하였다. 다양한 용접조건을 이용하여 실험을 수행하였고 이를 정량적으로 분석하였다. 계측된 신호와 용접 품질은 비선형적 관계를 가지고 있으므로 본 연구에서는 용접 품질을 예측하는 방법으로 퍼지 패턴인식 알고리즘을 이용하는 방법과 계측 신호를 이용한 인장강도 예측모델을 이용하여 병렬로 품질평가를 할 수 있는 알고리즘을 구현하였다. 이를 위하여 계측된 신호와 용접 품질과의 관계를 이용하여 퍼지 규칙 베이스 정의하였고, 신경회로망 모델을 이용하여 인장강도 예측모델을 제시하였다. 또한 품질 평가 알고리즘을 기반으로 레이저 용접부의 품질평가가 가능한 GUI 프로그램을 구현하였다.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.11 s.188
• /
• pp.68-77
• /
• 2006

Nowadays, the increasing global competition forces automobile manufacturer to increase quality and to reduce the cost and time for manufacturing planning. To solve these problems, automobile manufacturers try to apply digital manufacturing technologies. In this paper, a concept of method for planning the digital assembly system is proposed. Based on the requirements of assembly tasks obtained through product analysis, the function and sequence modeling for assembly process is executed using the IDEF0 and UML model. For implementation of digital assembly system, the selected components are modeled by using 3D CAD tools. According to the system configuration strategy, lots of the alternative solutions for the assembly system are generated. Finally, the optimal assembly system is chosen by the evaluation of the alternative solutions with TOPSIS(Technique for Order Preference by Similarity to Ideal Solution) method. According to proposed procedure, digital laser welding system is implemented in DELMIA.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.23 no.6
• /
• pp.616-621
• /
• 2003

There are various Non-Destructive Evaluation (NDE) techniques used for measurement of residual stresses in material, such as magnetic methods, X-ray diffraction, Ultrasonic velocity measurement etc. The capabilities, applications and limitations of these techniques for evaluation of cold work/plastic deformation were studied and compared. Mild steel plates were subjected to different degree of cold deformation and were analyzed by Magneto-mechanical Acoustic Emission (MAE), Barkhausen Noise (BN) and magnetic properties (hysteresis loop parameters analysis). Further, these specimens were analyzed by X-ray diffraction and ultrasonic velocity measurements. The microhardness measurement and microstructure studies of these cold worked plates were also carried out. The results of all these studies and comparison of different techniques are discussed in this paper.

• Journal of Welding and Joining
• /
• v.16 no.6
• /
• pp.68-76
• /
• 1998

A CCD camera with a laser stripe was applied to realized the automatic weld seam tracking. The 3-dimensional information obtained from the vision system made it possible to generate the weld torch path. The adaptive Hough transformation was used to extract laser stripes an to obtain specific weld points. It takes relatively long time to process image on-line control using the basic control using the basic Hough transformation, but it has a tendency of robustness over the noises such as spatter. For this reason, it was complemented with adaptive Hough transformation to have an on-line processing ability for scanning specific weld points. The dead zone, where the sensing of weld line is impossible, was eliminated by rotating the camera with its rotating axis centered at the weld torch. When weld lines were detected, the camera angle was controlled in order to get the minimum image data for sensing of weld lines. Consequently, the image processing time was reduced.

• Journal of the Korean Society of Safety
• /
• v.14 no.4
• /
• pp.53-59
• /
• 1999

Recently, Tailor Welded Blank (TWB) is widely used in automotive industry since the transformation characteristic of its material can be changed. However, clearance between welding surfaces becomes the important factor which affect the quality of the laser weld, causing difficulties in preparing the sheet. The objective of this paper is to systematically evaluate the effects of previously presented fracture criterion and shearing condition on precise mechanical shearing simulation result. For this purpose, a parametric study was peformed to investigate the effect of finite element size and fracture criterion on simulation result. Also, in order to predict the optimum shearing condition, effect of shearing conditions such as clearance and punch radius on the shear plane shape was evaluated.

• Journal of Welding and Joining
• /
• v.23 no.5
• /
• pp.30-36
• /
• 2005

In this part, thermal finite element analysis(FEA) is conducted for the experiments in part 1. The molten area of base metals are analyzed by FEA results and compared with experimental ones. Temperature data from FEA results are used to calculate the IMC layer thickness analytically at the interface. IMC layer is established as a function of time and temperature when there is an interaction between solid steel and molten aluminum. The IMC layer thickness is obtained by cumulative computations using the time-temperature data from FEA results.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.23 no.3
• /
• pp.279-286
• /
• 2015

To achieve lightweight design, research & development of various lightweighting technologies such as hydroforming are underway worldwide. In the case of hydroforming, application of ultra high strength steel is essential for weight reduction of the car. However, considering common high-strength carbon steel, it is not suitable to the actual hydroformed parts since the lack of formability. DP steel offers an outstanding combination of strength and formability as a result of their microstructure. DP steel has high strength and good formability but it's difficult to secure stable quality of welding section because of softening of weld section and chemical composition. Therefore, most of companies use LASER welding when making high strength tube. Electric resistance welding is excellent production method for steel tube manufacturing considering the productivity. Optimum electric resistance welding technology is needed to be developed for application of high strength hydroformed parts using DP steel. This study is comprehensive research & development from electric resistance welding to actual formabililty evaluation.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.1 no.1
• /
• pp.39-49
• /
• 2009

The use of high-strength aluminum alloys is increasing in shipbuilding industry, particularly for the design and construction of war ships, littoral surface craft and combat ships, and fast passenger ships. While various welding methods are used today to fabricate aluminum ship structures, namely gas metallic arc welding (GMAW), laser welding and friction stir welding (FSW), FSW technology has been recognized to have many advantages for the construction of aluminum structures, as it is a low-cost welding process. In the present study, mechanical properties of friction stir welded aluminum alloys are examined experimentally. Tensile testing is undertaken on dog-bone type test specimen for aluminum alloys 5083 and 5383. The test specimen includes friction stir welded material between identical alloys and also dissimilar alloys, as well as unwelded (base) alloys. Mechanical properties of fusion welded aluminum alloys are also tested and compared with those of friction stir welded alloys. The insights developed from the present study are documented together with details of the test database. Part of the present study was obtained from the Ship Structure Committee project SR-1454 (Paik, 2009), jointly funded by its member agencies.

• Journal of Welding and Joining
• /
• v.30 no.1
• /
• pp.59-63
• /
• 2012

The spacer grid is one of the main structural components in a fuel assembly. It supports fuel rods, guides cooling water and maintains geometry from external impact load and cyclic stress by the vibration of nuclear fuel rod, it is necessary to have sufficient strength against dynamic external load and fatigue strength. In this study, the mechanical properties and fatigue characteristics of laser beam welded zircaloy thin sheet are examined. The material used in this study is a zirconium alloy with 0.66 mm of thickness. The fatigue strength under cyclic load was evaluated at stress ratio R=0.1. S-N curves are presented with statistical testing method recommend by JSME- S002 and compared with S-N curves at R.T. and $315^{\circ}C$. As a result of the experimental approach, the design guide of fatigue strength is proposed and the results obtained from this study are expected to be useful data for spacer gird design.