• 대한전자공학회논문지SD
• /
• 제39권11호
• /
• pp.1-6
• /
• 2002

본 논문에서는 High speed DRAM의 speed 특성을 향상시키기 위한 Laser_Repair Condition 최적화의 한 방안을 구현하였다. 구현 방법은 먼저 Wafer내의 개별 Die별 DC Generator level을 확인하고 최약 DC Generator를 파악한 후 AC parameter의 margin을 check하고 AC parameter의 특성을 개선시킬 수 있는 DC Generator level을 forcing하여 test하여 개선 효과를 곧장 확인하였고 그에 대한 Fuse cutting inform을 생성하여 Laser_Repair 공정에서 적용하여 Post_Laser test시 개선 효과를 확인하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 D
• /
• pp.2662-2664
• /
• 2004

레이저 시스템의 정밀한 동작시점 제어를 위해서 초정밀 동기용 시간 지연 발생기(time delay generator)를 제작하였다. 제작된 장치는 8 비트 delay line IC를 조합하여 구현하였으며 사용자 프로그램에서 지연 시간과 펄스폭을 설정할 수 있도록 하였다. 또한 RS232 통신 방식으로 설정 값을 전달할 수 있도록 하였고 모듈 단위로 2 개의 채널을 사용할 수 있도록 하였으며 7 비트 어드레싱 방식의 $I^2C$(Inter IC Bus)를 이용할 경우 최대 127 개의 모들을 동작시킬 수 있도록 하였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.1540-1545
• /
• 2004

Measurement of concentration fields in a micro-channel is the crucial technology in the area of Lab-on-a-chip to be used for various bio-chemical applications. It is wel-known that the only possible way to measure the concentration field in the micro-channel is using micro-LIF(Laser Induced Fluorescence) method. However, an accurate concentration field at a given cross plane in a micro-channel has not been made so far due to the limit of light illumination. The present study demonstrates a novel method to provide an ultra thin laser sheet beam having 5 microns thickness by a micro focus laser line generator. Nile Blue A was used as fluorescent dye for LIF measurement. The laser sheet beam illuminates an exact plane of concentration measurement in the micro-channel to increase the signal to noise ratio and reduce the depth uncertainty considerably.

• Current Optics and Photonics
• /
• 제2권1호
• /
• pp.53-58
• /
• 2018

A novel X-band high speed frequency sweep signal generator based on a tunable optoelectronic oscillator (OEO) incorporating a frequency-swept laser is presented and the theoretical fundamentals of the design are explained. A prototype of the generator with tuning range from 8.8552 GHz to 10.3992 GHz and a fine step about 8 MHz is achieved. The generated radiofrequency signal with a single sideband (SSB) phase noise lower than -100 dBc/Hz@10KHz is experimentally demonstrated within the whole tunable range, without any narrow RF band-pass filters in the loop. And the tuning speed of the frequency sweep signal generator can reach to over 1 GHz/s benefiting from applying a novel dispersion compensation modular instead of several tens of kilometers of optical fiber delay line in the system.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2006년도 추계학술대회 논문집
• /
• pp.1320-1325
• /
• 2006

Railway track supports and guides train and it directly affects ride quality and safety. To maintain track quality, regular maintenance activity is essential but it degrades track usage since maintenance activity occupies the track during the work. To achieve maximum track efficiency, track inspection should be performed at commercial running speed. In this paper, we designed and developed high speed rail profile measurement system using laser light sectioning method with line laser generator, digital camera and DSP based image processing system. The measurement system can supports rail profile measurement at the speed of 300 Km/h that can be applied to KTX.

• 한국가시화정보학회:학술대회논문집
• /
• 한국가시화정보학회 2004년도 추계학술대회 논문집
• /
• pp.86-89
• /
• 2004

One most feasible way to measure the concentration field in the micro-channel is using micro-LIF(Laser Induced Fluorescence) method. However, an accurate concentration field at a given cross plane in a micro-channel has not been successfully achieved so far due to various limitations in the light illumination and fluorescence signal detection. The present study demonstrates a novel method to provide an ultra thin laser sheet beam having five(5) microns thickness by use of a micro focus laser line generator. The laser sheet beam illuminates an exact plane of concentration measurement field to increase the signal to noise ratio and considerably reduce the depth uncertainty. Nile Blue A was used as fluorescent dye for the present LIF measurement. The enhancement of the fluorescent intensity signals was performed by a solvent mixture of water $(95\%)$ and ethanol (EtOH)/methanol (MeOH) $(5\%)$ mixture. To reduce the rms errors resulted from the CCD electronic noise and other sources, an expansion of grid size was attempted from $1\times1$ to 3(3 or 5(5 pixel data windows and the pertinent signal-to-noise level has been noticeably increased accordingly.

• 한국가시화정보학회:학술대회논문집
• /
• 한국가시화정보학회 2004년도 Proceedings of 2004 Korea-Japan Joint Seminar on Particle Image Velocimetry
• /
• pp.65-74
• /
• 2004

Measurement of concentration distributions of suspended particles in a micro-channel is out of the most crucial necessities in the area of Lab-on-a-chip to be used for various bio-chemical applications. One most feasible way to measure the concentration field in the micro-channel is using micro-LIF(Laser Induced Fluorescence) method. However, an accurate concentration field at a given cross plane in a micro-channel has not been successfully achieved so far due to various limitations in the light illumination and fluorescence signal detection. The present study demonstrates a novel method to provide an ultra thin laser sheet beam having five(5) microns thickness by use of a micro focus laser line generator. The laser sheet beam illuminates an exact plane of concentration measurement field to increase the signal to noise ratio and considerably reduce the depth uncertainty. Nile Blue A was used as fluorescent dye for the present LIF measurement. The enhancement of the fluorescent intensity signals was performed by a solvent mixture of water $(95\%)$ and ethanol (EtOH)/methanol (MeOH) $(5\%)$ mixture. To reduce the rms errors resulted from the CCD electronic noise and other sources, an expansion of grid size was attempted from $1\times1\;to\;3\times3\;or\;5\times5$ pixel data windows and the pertinent signal-to-noise level has been noticeably increased accordingly.

• 마이크로전자및패키징학회지
• /
• 제17권4호
• /
• pp.73-76
• /
• 2010

A two-facet approach was used to investigate the parametric performance of functional high-speed DDR3 (Double Data Rate) DRAM (Dynamic Random Access Memory) die placed in different types of BGA (Ball Grid Array) packages: wire-bonded BGA (FBGA, Fine Ball Grid Array), flip-chip (FCBGA) and lead-bonded $microBGA^{(R)}$. In the first section, packaged live DDR3 die were tested using automatic test equipment using high-resolution shmoo plots. It was found that the best timing and voltage margin was obtained using the lead-bonded microBGA, followed by the wire-bonded FBGA with the FCBGA exhibiting the worst performance of the three types tested. In particular the flip-chip packaged devices exhibited reduced operating voltage margin. In the second part of this work a test system was designed and constructed to mimic the electrical environment of the data bus in a PC's CPU-Memory subsystem that used a single DIMM (Dual In Line Memory Module) socket in point-to-point and point-to-two-point configurations. The emulation system was used to examine signal integrity for system-level operation at speeds in excess of 6 Gb/pin/sec in order to assess the frequency extensibility of the signal-carrying path of the microBGA considered for future high-speed DRAM packaging. The analyzed signal path was driven from either end of the data bus by a GaAs laser driver capable of operation beyond 10 GHz. Eye diagrams were measured using a high speed sampling oscilloscope with a pulse generator providing a pseudo-random bit sequence stimulus for the laser drivers. The memory controller was emulated using a circuit implemented on a BGA interposer employing the laser driver while the active DRAM was modeled using the same type of laser driver mounted to the DIMM module. A custom silicon loading die was designed and fabricated and placed into the microBGA packages that were attached to an instrumented DIMM module. It was found that 6.6 Gb/sec/pin operation appears feasible in both point to point and point to two point configurations when the input capacitance is limited to 2pF.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 추계학술대회 논문집
• /
• pp.199-203
• /
• 2001

It is well know that the interest on the on-line sensing of tool wear is groeing more and more with the aim of controlling machine tools productivity form the point of view of quality and quantity. This paper describes the sensing of the amount of flank wear with vision system. To obtain a proper image He-Ne laser generator is used as the lighting source and obtained image is processed with block processing algorithm and morphological image processing method. By means of this system it is possible to evaluate the parameters of tool wear. Experimental tests performed with this system on an NC lathe have shown good performances here described and discussed.

• 한국정보통신학회논문지
• /
• 제5권7호
• /
• pp.1295-1300
• /
• 2001

본 논문에서는 광디스크 메모리의 재생성능에 주요한 영향을 미치는 jitter를 향상시키는 방법이 검토되었다. 광디스크 제조공정에 있어서 타공정의 변수를 고정한 상태에서 단일의 조작을 통해 jitter value를 저감화시키기 위해 펄스 폭 조정기를 제작하였다. 펄스 폭 조정기폭 적용하여 입력신호의 level을 조정한 결과 6.9%의 최소 jitter value를 확보하였다.