• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.679-682
• /
• 2003

We report the suitable SLS (sequential lateral solidification) as a function of laser intensity. Precursor film is changed from 50nm to 100nm and is deposited on glass substrate by PECVD. We can find the suitable SLS length by changing the mask size. In this paper, we present the well-defined grain growth conditions as a function of laser intensity.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.252-255
• /
• 2003

The pulsed laser deposition process modeling is investigated using neural networks based on radial basis function networks and multi-layer perceptron. Two input factors are examined with respect to the PL intensity. In order to minimize the joint confidence region of fabrication process with varying the conditions, D-optimal experimental design technique is performed and photoluminescence intensity is characterized by neural networks. The statistical results were then used to verify the fitness of the nonlinear process model. Based on the results, this modeling methodology can be optimized process conditions for pulsed laser deposition process.

• Journal of the Optical Society of Korea
• /
• v.10 no.2
• /
• pp.86-90
• /
• 2006

The external feedback effect on the relative intensity noise (RIN) characteristics of blue InAlGaN laser diode has been analyzed taking into account the spontaneous emission noise and the injection current for the high frequency modulation. A Langevin diffusion model was exploited to characterize its relative intensity noise. The simulation parameters were quantitatively evaluated from the optical gain properties of the InAlGaN multiple quantum well active regions by using the multiband Hamiltonian for the strained wurtzite crystals. The extracted parameters were then applied to the rate equations taking into account the external feedback and the high frequency modulation current. The RIN characteristics were investigated to optimize the low frequency laser diode noise characteristics.

• Journal of Institute of Control, Robotics and Systems
• /
• v.14 no.6
• /
• pp.558-563
• /
• 2008

Optical axis misalignment, which represents the position deviation of the objective lens from the optical axis, is an inevitable assembly error in an optical pick-up. Since the laser power intensity varies with respect to the distance from the optical axis, the misalignment leads to variation of the laser spot power intensity, which is one of the critical factors increasing data bit-error-rate in optical disc drives. In this paper, an auto-adjustment scheme for optical axis alignment is proposed to eliminate the undesirable variation of the laser spot power intensity in optical disc drives. An envelope of the data RF signal is extracted and utilized to detect the optical axis misalignment. Then an adjustment input is added to the driving input of the tracking actuator to shift the objective lens to the optical axis. Finally, the feasibility is verified by experiments.

• Current Optics and Photonics
• /
• v.2 no.5
• /
• pp.395-399
• /
• 2018

This article investigates the mechanism of electronic signal phase noise degradation induced by laser phase noise in optical links comprising optical resonators. Through theoretical derivation, we find that the phase noise of the output electronic signal has the same spectral shape of optical intensity noise as the output of the optical resonator. We propose that the optical resonator transfers laser phase noise to light intensity fluctuation and then the intensity fluctuation is converted to electric phase noise through AM-PM conversion mechanism in the photodiode. An optical link comprising a Fabry-Perot resonator was constructed to verify the proposed mechanism. The experimental results agree with our theoretical prediction verifying that the supposition is correct.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.18 no.3
• /
• pp.293-299
• /
• 2015

We analyzed the damage effect on Glass Fibre Reinforced Plastics(GFRP) under air flow by irradiation of continuous wave near-IR laser. Damage process and temporal temperature distribution were demonstrated and material characteristics were observed with laser intensity, surface flow speed and angle. Surface temperature on GFRP rapidly increased with laser intensity, and the damaged pattern was different with flow characteristics. In case of no flow, penetration on GFRP by burning and flame generation after laser irradiation was appeared at once. GFRP was penetrated by the heat generated from resin ignition. In case of laser irradiation under flow, a flame generated after burning extinguished at once by flow and penetration pattern on GFRP were differently shown with flow angle. From the results, we presented the damage process and its mechanism.

• Journal of Advanced Marine Engineering and Technology
• /
• v.31 no.8
• /
• pp.961-969
• /
• 2007

The laser material processing has replaced a conventional material processing such as a welding, cutting, drilling and surface modification and so on. LTH(Laser Transformation Hardening) is one branch of the laser surface modification process. A lot of energy is needed for the LTH process to elevate workpiece surface to temperature of the austenite transformation($A_3$), which results from utilizing a beam with a larger size and lower power intensity comparatively. The absorptivity of the laser energy with respect to material depends on the wave length of a beam. This study is related to the surface hardening for the rod-shaped carbon steel by the high power diode laser(HPDL) whose beam absorptivity is better than conventional types of lasers such as $CO_2$ or Nd:YAG laser. Because a beam proceeds on the rotating specimen the pretreated hardened-phase can be tempered and softened by the overlapping between hardened tracks. Accordingly, the longitudinal hardness measurement and observation of the micro structure was carried out for an assessment of the hardening characteristics. In addition, a hardening characteristics as a hardenability of materials was compared in the point of view of the hardness distribution and hardening depth and width.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.48 no.4
• /
• pp.261-268
• /
• 1999

Laser-induced thermochemical etching has been recognized as a new powerful method for processing a variety of materials, including metals, semiconductors, ceramics, insulators and polymers. This study presents characteristics of direct etching for Si substrate using focused argon ion laser beam in aqueous KOH and $CCl_2F_2$ gas. In order to determine process conditions, we first theoretically investigated the temperature characteristics induced by a CW laser beam with a gaussian intensity distribution on a silicon surface. Major process parameters are laser beam power, beam scan speed and reaction material. We have achieved a very high etch rate up to $434.7\mum/sec$ and a high aspect ratio of about 6. Potential applications of this laser beam etching include prototyping of micro-structures of MEMS(micro electro mechanical systems), repair of devices, and isolation of opto-electric devices.

• Transactions of the Society of Information Storage Systems
• /
• v.6 no.1
• /
• pp.1-5
• /
• 2010

Holographic data storage system(HDSS) has many noise sources - crosstalk, scattering and inter pixel interference, etc. Generally the intensity of a light generated from the laser source has Gaussian distribution and this ununiformity of light also can make the data page to have a low SNR. A beam apodizer is used to make the laser as a flat-top beam but the intensity distribution is not strictly uniform. The intensity of light can be controlled using image mask. In this paper the intensity distribution of light used for HDSS is controlled by a digital image mask. The digital image mask is changed arbitrarily in real-time with suggested algorithm for the HDSS.

• Laser Solutions
• /
• v.16 no.1
• /
• pp.5-9
• /
• 2013

We have successfully formed filament inside of a transparent soda-lime glass using a Ti:sapphire based femtosecond laser. To make filament form, keeping the laser intensity higher than critical intensity is essential. Also each of the machining parameters plays an important role for the formation of filament. In this paper, we study what parameter can possibly influence for formation of filament, and we introduce an application using filamentation by femtosecond laser for transparent material.